2009 Peugeot 207 Dag ignition
[x] Cancel search: ignitionPage 120 of 267
i
126
CRUISE CONTROL
System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.
The cruise control is switched onmanually: it requires a minimum vehicle speed of 25 mph (40 km/h), as well as the engaging:
- of fourth gear on the manual gear-box,
- of second gear with the "2 Tronic" or automatic gearbox, in sequential mode,
- of position A on the "2 Tronic" gear-box or D on the automatic gearbox.
The cruise control is switched off manu- offally or by pressing the brake or clutch pedal or on triggering of the ESP sys-tem for safety reasons.
It is possible to exceed the programmed speed temporarily by pressing the ac-celerator pedal.
To return to the programmed speed, simply release the accelerator pedal.
Switching off the ignition cancels any programmed speed value.
The controls of this system are grouped together on lever A .
1. Cruise control mode selection dial
2. Value decrease button
3. Value increase button
4. Cruise control off/resume button
The programmed information is grouped together on the instrument panel dis-play.
5. Cruise control off/resume indication
6. Cruise control mode selection indication
7. Programmed speed value
Steering wheel controls Displays on the instrument panel
Page 126 of 267
133
CHECKING LEVELS
Check all of these levels regularly and top them up if necessary, unless other-wise indicated.
I f a l e v e l d r o p s s i g n i fi c a n t l y , h a v e t h e corresponding circuit checked by a PEUGEOT dealer.
Brake fluid level To avoid any risk of scalding, unscrew the cap by two turns to allow the pres-sure to drop. When the pressure has dropped, remove the cap and top up the level.
Oil level
The reading will only be correct if the vehicle is on level ground and the engine has been off for more than 15 minutes.
The check is carried out either when the ignition is switched on using the oil level indicator on the instrument panel, or using the dipstick.
Between two oil changes, the consump-tion should not exceed 0.5 litre per 600 miles (1,000 km).
T h e b r a k e fl u i d l e v e l s h o u l d b e close to the "MAX" mark. If it is not, check the brake pad wear.
Draining the circuit
Refer to the servicing booklet for details of the interval for this operation.
Coolant level
The coolant level should be close to the "MAX" mark but should never exceed it.
When the engine is warm, the temperature of the coolant is regulated by the fan. This can operate with the ignition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h a p a r - t i c l e e m i s s i o n fi l t e r , t h e f a n m a y o p e -rate after the vehicle has been switched o f f , e v e n i f t h e e n g i n e i s c o l d .
In addition, as the cooling system is pressurised, wait at least one hour after switching off the engine before carrying out any work.
W a s h - w i p e a n d h e a d l a m p w a s h
fluid*
T h e m i n i m u m l e v e l o f t h i s fl u i d is indicated by an audible signal and a message on the multifunc-tion display.
Top up the level when you stop the vehicle.
* According to country.
Draining the engine
Refer to the servicing booklet for details of the interval for this operation.
In order to maintain the reliability of the engine and emission control system, the use of additives in the engine oil is prohibited.
O i l s p e c i fi c a t i o n
The oil must correspond to your engine and conform to the manufacturer's recommendations.
F l u i d s p e c i fi c a t i o n
T h e b r a k e fl u i d m u s t c o n f o r m t o t h e manufacturer's recommendations and f u l fi l t h e D O T 4 s t a n d a r d s .
Draining the circuit
The coolant does not have to be changed.
F l u i d s p e c i fi c a t i o n
The coolant must conform to the manu-facturer's recommendations.
F l u i d s p e c i fi c a t i o n
To guarantee optimum cleaning and avoid freezing, water should not be u s e d t o t o p u p o r r e p l a c e t h i s fl u i d .
Page 130 of 267
i
136
This repair kit is available from
PEUGEOT dealers.
It is designed to repair most punc-
tures which could affect the tyre, lo-
cated on the tyre tread or shoulder.
Avoid removing any foreign bodies
which have penetrated the tyre.
TEMPORARY PUNCTURE
REPAIR KIT
Complete system consisting of a com-
pressor and an incorporated sealant
cartridge which permits temporary re-
pair of the tyre so that you can drive to
the nearest garage. Using the kit
This procedure, comprising several
steps, must be carried out in full.
Switch off the ignition.
Turn the selector A to the "SEALANT"
position.
Check that the switch B is in posi-
tion "0" .
Connect the white pipe C to the
valve of the tyre to be repaired.
Connect the compressor's electric
plug to the vehicle's 12 V socket.
A f fi x t h e s p e e d l i m i t a t i o n s t i c k e r t o t h e
vehicle's steering wheel to remind you
that a wheel is in temporary use.
Start the vehicle and leave the en-
gine running.
Access to the kit
Page 146 of 267
152
Fuse N° Rating Functions
F8 20 A Audio equipment, audio/telephone, multifunction
display, clock, steering wheel controls, tyre
u n d e r - i n fl a t i o n d e t e c t i o n , t r a i l e r f u s e b o x .
F9 30 A F r o n t 1 2 V s o c k e t , r e a r 1 2 V s o c k e t ( S W ) .
F10 15 A Alarm siren, alarm control unit, directional
headlamps.
F11 15 A Diagnostic socket, low current ignition switch,
a u t o m a t i c g e a r b o x c o n t r o l u n i t .
F12 15 A R a i n / b r i g h t n e s s s e n s o r , a m p l i fi e r , t r a i l e r f u s e b o x ,
driving school module.
F13 5 A E n g i n e f u s e b o x , A B S r e l a y , d u a l - f u n c t i o n b r a k e
s w i t c h , " 2 T r o n i c " g e a r b o x g e a r l e v e r .
F14 15 A Instrument panel, seat belt warning lights bar,
headlamp adjustment, air conditioning, hands-free
kit, rear parking assistance control unit, air bags.
F15 30 A Locking and deadlocking.
F17 40 A R e a r s c r e e n a n d e x t e r i o r m i r r o r s d e - i c i n g .
SH - PARC shunt.
Page 150 of 267
!
!
i
156
Do not disconnect the terminals
while the engine is running.
Do not charge the batteries without
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
Do not push the vehicle to start the
e n g i n e i f i t i s fi t t e d w i t h a " 2 T r o n i c "
g e a r b o x .
The batteries contain harmful sub-
stances such as sulphuric acid and
lead. They must be disposed of in
accordance with regulations and
must not, in any circumstances, be
discarded with household waste.
Take used remote control batteries
and vehicle batteries to a special
collection point.
Charging the battery using a
battery charger
Disconnect the battery from the ve-
hicle.
Follow the instructions for use pro-
vided by the manufacturer of the
charger.
Reconnect starting with the nega-
t i v e t e r m i n a l ( - ) .
Check that the terminals and connec-
tors are clean. If they are covered with
s u l p h a t e ( w h i t i s h o r g r e e n i s h d e p o s i t ) ,
remove them and clean them.
LOAD REDUCTION MODE
System which manages the use of cer-tain functions in relation to the level of charge remaining in the battery.
When the vehicle is being driven, the load reduction function temporarily deactivates certain functions, such as the air condi-tioning, the rear screen de-icing...
The deactivated functions are reactivat-ed automatically as soon as conditions permit.
It is advisable to disconnect the
battery if the vehicle is to be left un-
used for more than one month. Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the doors
before disconnecting the battery.
Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit in-
itialisation of the electronic systems.
H o w e v e r , i f s l i g h t d i f fi c u l t i e s a r e e n -
countered following this operation,
contact a PEUGEOT dealer.
Referring to the corresponding sec-
t i o n , y o u m u s t y o u r s e l f r e i n i t i a l i s e :
- the remote control key,
- the one-touch electric windows,
- the GPS satellite navigation
system.
Page 151 of 267
!
!
i
156
Do not disconnect the terminals
while the engine is running.
Do not charge the batteries without
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
Do not push the vehicle to start the
e n g i n e i f i t i s fi t t e d w i t h a " 2 T r o n i c "
g e a r b o x .
The batteries contain harmful sub-
stances such as sulphuric acid and
lead. They must be disposed of in
accordance with regulations and
must not, in any circumstances, be
discarded with household waste.
Take used remote control batteries
and vehicle batteries to a special
collection point.
Charging the battery using a
battery charger
Disconnect the battery from the ve-
hicle.
Follow the instructions for use pro-
vided by the manufacturer of the
charger.
Reconnect starting with the nega-
t i v e t e r m i n a l ( - ) .
Check that the terminals and connec-
tors are clean. If they are covered with
s u l p h a t e ( w h i t i s h o r g r e e n i s h d e p o s i t ) ,
remove them and clean them.
LOAD REDUCTION MODE
System which manages the use of cer-tain functions in relation to the level of charge remaining in the battery.
When the vehicle is being driven, the load reduction function temporarily deactivates certain functions, such as the air condi-tioning, the rear screen de-icing...
The deactivated functions are reactivat-ed automatically as soon as conditions permit.
It is advisable to disconnect the
battery if the vehicle is to be left un-
used for more than one month. Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the doors
before disconnecting the battery.
Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit in-
itialisation of the electronic systems.
H o w e v e r , i f s l i g h t d i f fi c u l t i e s a r e e n -
countered following this operation,
contact a PEUGEOT dealer.
Referring to the corresponding sec-
t i o n , y o u m u s t y o u r s e l f r e i n i t i a l i s e :
- the remote control key,
- the one-touch electric windows,
- the GPS satellite navigation
system.
Page 178 of 267
183
In an emergency , press this button for more than 2 seconds. Flashing of the green diode and a voice m e s s a g e c o n fi r m t h a t t h e c a l l h a s b e e n m a d e t o t h e PEUGEOT Emergency team * .
Pressing this button again immediately cancels the request. The green diode switches off.
T h e g r e e n d i o d e r e m a i n s o n ( w i t h o u t fl a s h i n g ) w h e n c o m m u n i c a t i o n i s established. It switches off at the end of communication.
This call is dealt with by the PEUGEOT Emergency t eam which receives locating information from the vehicle and can send a detailed alert to the appropriate emergency services. In countries in whi ch the team is not operational, or when the locating service has been expressly refused, the c a l l i s d e a l t w i t h d i r e c t l y b y t h e e m e r g e n c y s e r v i c e s ( 1 1 2 ) w i t h o u t l o c a t i n g .
If an impact is detected by the air bag ECU, and i ndependently of any triggering of the air bags, an emergency cal l is made automatically.
* This service is subject to conditions and availability. Consult a PEUGEOT dealer.
Press this button for more than 2 seconds to reque st a s s i s t a n c e ( v e h i c l e b r e a k d o w n ) . A v o i c e m e s s a g e c o n fi r m s t h a t t h e c a l l h a s b e e n m a d e * * .
Pressing this button again immediately cancels the request. T h e c a n c e l l a t i o n i s c o n fi r m e d b y a v o i c e m e s s a g e .
** This service is subject to conditions and availability. Consult a PEUGEOT dealer.
When the ignition is switched on, the green indicator light comes on for 3 seconds indicating that the system is operating correctly.
I f t h e o r a n g e i n d i c a t o r l i g h t fl a s h e s : t h e r e i s a system malfunction. I f t h e o r a n g e i n d i c a t o r l i g h t i s l i t c o n t i n u o u s l y : the backup battery must be replaced. In both cases, consult a PEUGEOT dealer.
EMERGENCY OR ASSISTANCE CALL
Page 238 of 267
243
0 7
1
2
3
2
1
4
T h e s e r v i c e s a v a i l a b l e d e p e n d o n t h e n e t w o r k , t h e
S I M c a r d a n d t h e c o m p a t i b i l i t y o f t h e B l u e t o o t h equipment used. Refer to your telephone's manual an d your operator to check which services you have access to. A list of mobile telephones which offer the best range of services is available from dealers.
BLUETOOTH TELEPHONE
CONNECTING A TELEPHONE
For reasons of safety and because they require pro longrolonged attention o n t h e p a r t o f t h e d r i v e r , t h e o p e r a t i o n s f o r p a i r i n g t h e B l u e t o o t h o n t h e p a r t o f t h e d r i v e r , t h e o p e r a t i o n s f o r p a i r i n g t h e B l u e t o o t h mobile telephone to the hands-free system of the PC Na PC Nav must be carried out with the vehicle stationary. The ignition must must be on.
A c t i v a t e t h e t e l e p h o n e ' s B l u e t o o t h f u n c t i o n . The last telephone connected is reconnected automatically.
Enter the authentication code on the telephone. The code to be entered is displayed on the screen.
To change the telephone connected, press the PHONE button, then select "Phone" Menu and press the dial to c o n fi r m .
Once the telephone has been connected, PC Nav can s can synchronise the address book and the call list. This synchronisation ation may take a few minutes.
Select "Connect phone". Select the t e l e p h o n e a n d p r e s s t o c o n fi r m .
T h e l i s t o f t e l e p h o n e s c o n n e c t e d p r e v i o u s l y ( 4 m a x i m u m ) a p p e a r s T h e l i s t o f t e l e p h o n e s c o n n e c t e d p r e v i o u s l y ( 4 m a x i m u m ) a p p e a r s on the multifunction screen. Select the telephone requir required for a new connection.
Press the PHONE button.
F o r a fi r s t c o n n e c t i o n , s e l e c t "Search phone" and press the dial to c o n fi r m . T h e n s e l e c t t h e n a m e o f t h e telephone.
SEARCH PHONE
CONNECT PHONE