2009 OPEL MERIVA spare wheel

154 Driving and operationFitting new tyres
Fit tyres in pairs or in sets, which is even
better. Ensure that tyres on one axle are
zthe same size
z the same design
z the same make
z and have the same tread pattern
Fit directional tyres such that they roll in the
direction of travel. The rolling direction is
indicated by a symbol (e.g. an arrow) on
the sidewall.
Tyres fitted opposing the rolling direction
(such as when changing a tyre) should be
refitted as soon as possible. This is the only
way to benefit fully from the design
properties of the tyre.
Pay attention to legal requirements when
disposing of tyres.
Picture no: 14194s.tif
Tyre pressure
Check tyre pressure, including the spare
wheel, at least every 14 days and prior to
any long journey; the tyres should be
checked when cold. Do n’t forget to check
the spare wheel 3.
Remove the valve cap key from the tank
flap and use it to unscrew the valve cap.
Tyre pressure 3228 and on the adhesive
label 3 on the inside of the tank flap.
The tyre pressure data is for cold tyres. It
applies to both summer and winter tyres. Always inflate the spare wheel
3 to the
pressure specified for full load.
Do not reduce tyre pressure when the tyres
are warm. Otherwise the pressure may
drop below the permissible minimum when
the tyres cool down.
After having checked the tyre pressure,
tighten the valve caps using the valve cap
key.
Incorrect inflation pressures will impair
safety, vehicle handling, comfort and fuel
economy and will increase tyre wear.

157
Driving and operation
Winter tyres 3
Notes on fitting new tyres 3 154.
Restrictions 3228.
Winter tyres improve driving safety at
temperatures below 7 C.
The design of summer tyres means they
have limited qualities for winter driving.
In accordance with country-specific
regulations, affix the speed sticker 3 in the
driver’s field of view.
If you use the spare wheel when it is fitted
with a summer tyre, the vehicle’s
driveability may be affected, especially on
slippery road surfaces. Obtain a
replacement for the faulty tyre as soon as
possible, and have the wheel balanced
and fitted to the vehicle.
Wheel covers 3
Use of wheel trims and tyres that approved
by Opel for the vehicle in question and
thereby fulfil all requirements for the wheel
and tyre combination.
If the wheel trims and tyres used are not
Opel-approved, the ty res must not have a
beaded edge. Wheel trims must not impair brake cooling.
Remove the wheel trims if fitting tyre
chains
3.
Picture no: 6459u.tif
Tyre chains 3
Restrictions and further information 3 228.
Tyre chains are only permitted on the
driven wheels (front axle). They must be
fitted to the tyres symmetrically in order to
achieve a concentric fit.
Always use fine mesh chains that add no
more than 10 mm to the tyre tread and the
inboard sides (including chain lock).
9 Warning
Use of unsuitable tyres or wheel trims
could lead to sudden loss of air and
thereby accidents.

158 Driving and operationRemove the wheel trims if using tyre chains
3174.
Tyre chains may only be used at speeds up
to 50 km/h. When travelling on roads that
are free of snow, they may only be used for
brief periods.
Tyre chains must not be used on the
temporary spare wheel. If you need to use
tyre chains after suffering a flat front tyre,
fit the temporary spare on the rear axle
and transfer one of the rear wheels to the
front axle.
Roof rack
3
For safety reasons and to avoid roof
damage we recommend using the Opel
roof rack system that is approved for your
vehicle.
Follow the usage instructions for the roof
rack.
Remove the roof rack when not in use.
Disengage covers concealing roof rack
mounts by pushing sliders in direction of
arrow (e.g. with coin) and remove. To close
roof rack mounts, insert covers at front and
engage sliders at rear.
Driving hints 3 135
Towing equipment
3
Only use towing equipment that has been
approved for your vehicle. Ask a workshop
to retrofit towing equipment. It may be
necessary to make changes that affect the
cooling system, heat shields or other
equipment.
Mounting dimensions of towing equipment
3232.
9 Warning
Damage may lead to tyre blowout.

159
Driving and operation
Picture no: 14195s.tif
Towing equipment with
removable coupling ball bar
3
Stowage of coupling ball bar
The coupling ball bar is located in a bag
with the vehicle tools housed under the
spare wheel - see Fig. above.
Spare wheel 3 3172.
On vehicles with tyre repair kit 3, the
coupling ball bar is located in the left
stowage compartment beneath the floor
cover in the luggage compartment 3162,
Fig. 17923 S.
Picture no: 15271s.tif
Fitting the coupling ball bar
Fold down the socket. Remove the sealing
plug from the hole for the coupling ball bar
and stow it in the luggage compartment.
Picture no: 12416t.tif
Checking the tensioning of the coupling ball bar

z Red marking on rotary knob must point
towards white marking on coupling ball
bar.
z The gap between the rotary knob
and the coupling ball bar must be
approx. 4 mm.
z Key in the lock must be at position 1.
Caution
The coupling ball bar is to be removed
when not towing.

162 Driving and operation
Picture no: 17923s.tif
Stowage of coupling ball bar
Place coupling ball bar in bag and clip onto
the tool kit below the spare wheel 3159,
Fig. 14195 S.
On vehicles with tyre repair kit 3, the
coupling ball bar is stored in the left
stowage compartment beneath the floor
cover in the luggage compartment - see
Fig. above.
Caravan/trailer towingCaravan and trailer loads
1)
The permissible caravan/trailer loads are
vehicle and engine-dependent maximum
values which must not be exceeded. The
actual caravan/trailer load is the difference
between the actual gross weight of the
caravan/trailer and the actual coupling
socket load with the caravan/trailer
coupled.
The permissible caravan/trailer loads are
specified in the vehi cle documents. In
general, they are valid for gradients up to
maximum 12% The permitted caravan/trailer load applies
up to the specified incline and up to an
altitude of 1000 metres above sea level.
Since engine power decreases as altitude
increases because of the air becoming
thinner, therefore reducing climbing ability,
the permitted towing weight also
decreases by 10 % for
every 1000 metres of
additional altitude. The towing weight
does not have to be reduced when driving
on roads with slight inclines (less than 8 %,
e.g. motorways).
The permissible gross train weight must not
be exceeded. This weig ht is specified on
the identification plate 3218. 1)Observe national regulations.

165
Self-help, vehicle care
Self-help, vehicle care
Diesel fuel system, bleeding If the tank is allowed to run dry, the diesel
fuel system must be bled. Turn over the
ignition three times for 15 seconds at a
time. Then start the engine for a maximum
of 40 seconds
1). Repeat this process after
no less than 5 seconds. If the engine fails to
start, seek the assistance of a workshop.
Picture no: 16109s.tif
Bonnet Pull the release lever lo cated on the driver’s
side below the instru ment panel and push
it back to its original position.
Diesel fuel system, bleeding ............... 165
Bonnet .................................................. 165
Starting the engine with jump
leads 3............................................. 166
Towing .................................................. 168
Warning triangle ¨ 3,
First-aid kit +3................................. 171
Jack £ 3 and vehicle tools 3............ 171
Spare wheel 3...................................... 172
Changing wheels ................................. 174
Tyre repair kit 3................................... 178
Electrical system .................................. 181
Fuses and the most important circuits they protect ....................................... 182
Bulb replacement ................................ 185
Vehicle care.......................................... 196
1)For technical reasons, only 30 seconds are
possible on engines Y 17 DT and Z 17 DTH

168 Self-help, vehicle careRoute the leads so that they cannot catch
on rotating parts in the engine
compartment.
To start the engine:
1. Start the engine of the vehicle providing the jump start.
2. After 5 minutes, start the other engine. Start attempts shou ld be made at
intervals of 1 minute not last longer
than 15 seconds.
3. Allow both engines to idle for approx. 3 minutes with the leads connected.
4. Switch on electrical consumers (e.g. light, heated rear window) of the vehicle
receiving the jump start.
5. Reverse above sequence exactly when removing leads.
Picture no: 17896s.tif
Towing Towing your own vehicle
Disengage cap at bottom and remove
downwards.
Picture no: 14198s.tif
The towing eye is in the tool kit 3 in the
luggage compartment underneath the
spare wheel 3, see Fig. above, or for
versions with tyre repair kit 3, in the
storage compartment underneath the floor
cover, see Fig. 17918 S.

171
Self-help, vehicle care
Picture no: 16140s.tif
Warning triangle
¨ 3
,
First-aid kit
+3

The warning triangle and first aid cushion
are strapped with a rubber band in the
compartment on the le ft of the luggage
compartment beneath the floor covering.
Picture no: 14201s.tif
To open, remove the luggage
compartment cover 3 3 55, lift the floor
using the handle and raise toward the
front.
Picture no: 14203s.tif
Jack
£
3 and vehicle tools
3
Vehicles with spare wheel 3
The jack and vehicle tools are stowed in a
bag underneath the spare wheel in the
luggage compartment.
The jack 3 and the vehicle tools 3 have
been specially developed for your vehicle
and must only be used on that vehicle.
Only use jack for changing wheels.