2009 OPEL MERIVA tow

107
Lighting
Picture no: 14302s.tif
Lead-me lighting
3
Lead-me lighting when leaving the
vehicle 3
The dipped headlamps come on for
around 30 seconds after switching on and
closing the driver’s door.
To activate:
1. Switch off ignition.
2. Remove ignition key.
3. Open driver’s door.
4. Pull turn signal stalk toward steering
wheel.
5. Close driver’s door. If the driver’s door is left open, the lamps
will go out after two minutes.
The light is switched off immediately by
inserting the key into
the ignition or pulling
the turn signal stalk towards the steering
wheel again.
Picture no: 17920S.tif
Lead-me lighting when opening the
vehicle 3
The Lead-me-to-the-car lighting function
allows the dipped headlamps to be lit for
around 30 seconds using the remote
control.
This function must be activated (once):
Unlock the vehicle, put the key in the
ignition and press the light switch for
approx. 5 seconds - see next page,
Fig. 14136 S.
To deactivate the function permanently,
contact a workshop.

110 LightingBattery discharge protection
3
Some consumers such as the interior
lighting switch themselves off after
approx. 30 minutes if the ignition is off in
order to protect the battery charge. Misted light covers The inside of the light covers may mist up
briefly in poor, wet and cold weather
conditions, in heavy rain or after washing.
The mist disappears quickly by itself; to
help, switch on the lights. Headlamps when driving abroad The asymmetrical dipped beam increases
the field of vision on the passenger side of
the lane.
In countries where traffic drives on the
opposite side of the road, prevent glare as
follows.
Vehicles with halogen headlamp system
or Xenon headlamp system 3
Have headlights conver ted in a workshop.
Picture no: 14053h.tif
Vehicles with Adaptive headlight 3 (AFL)
1. Pull stalk towards steering wheel and hold.
2. Switch on ignition.
3. After approx. 3 seconds, an acoustic signal sounds and then AFL control
indicator
B flashes approx. 4 seconds.
After the switch, AFL control indicator
B
flashes for 4 seconds each time the ignition
is switched on. To return to asymmetrical dipped beam,
pull and hold the main beam stalk again,
switch on the ignition and wait for the
acoustic signal. AFL control indicator
B
will then discontinue flashing.
Control indicator
B
3 106.

116 Climate control
Picture no: 14144s.tif
Heating and ventilation system Temperature
Adjusted using left-hand rotary switch.
The amount of heat is dependent on the
coolant temperature and is thus not fully
attained until the engine is warm.
Picture no: 14145s.tif
Air flow
Adjusted using centre rotary switch.
The rate of air flow is determined by the
fan. The fan should therefore also be
switched on during a journey.
Picture no: 14146s.tif
Air distribution
Set using right rotary switch.
Open the air vents when the switch is set
toL or M .
red area = warm
blue area = cold
x
off
1-4 selected fan speed
Vto windscreen and front side
windows
J towards windscreen, front door
windows and footwell
K to footwell
L towards head area and footwell
M towards head area

118 Climate control
Picture no: 14151s.tif
Heating the foot well
zSet the temperature switch in the right-
hand zone.
z Switch on fan.
z Set air distribution switch to K.
Picture no: 16481s.tif
Demisting and defrosting windows
Misted or icy windows, e. g. due to damp
weather, damp clothing or low outside
temperatures:
z Turn the temperature switch clockwise as
far as it will go (warm). z
Set fan to 3 or 4 .
z Set air distribution switch to V.
z Switch on heated rear window Ü 3.
z Open side air vents as required and
direct them towards door windows.
z For simultaneous footwell heating, set
air distribution switch to J.
9 Warning
Disregard of the instructions could lead
to misting or icing of the windows and
subsequent accidents due to impaired
visibility.

121
Climate control
Picture no: 14162s.tif
Maximum cooling
Briefly open windows, sun roof and tilting
roof 3 so that warm air can escape quickly.
z Cooling n on
z Air recirculation system 4 on
z Turn the temperature switch
anticlockwise as far as it will go (cold)
z Set fan to 4
z Set air distribution switch to M
z Open all air vents
Picture no: 16482s.tif
Demisting and defrosting windows
Misted or icy windows, e. g. due to damp
weather, damp clothing or low outside
temperatures: z
Cooling n on, the air conditioning
compressor automatically switches itself
off at low outside temperatures (icing).
z Turn the temperature switch clockwise.
z Set fan to 3 or 4 .
z Air distribution switch to V, air
recirculation system 4 automatically
switches off,
– or –
if there is still moisture in the system after
previous air conditioning operation, the
windows may mist up. To prevent this,
set air distribution to K before starting
engine and set to V approx. 5 seconds
after starting.
z Activate heated rear window Ü.
z Open side air vents as required and
direct them towards the side windows.
9 Warning
Disregard of the instructions could lead
to misting or icing of the windows and
subsequent accidents due to impaired
visibility.

125
Climate control
Picture no: 16503s.tif
Activating and deactivating air
conditioning compressor
Press the ECO button. ECO appears in the
air conditioning display.
Switch on to sa ve fuel. In this m ode cooling
(AC compressor) is switched off.
Inflowing air is neither cooled nor
dehumidified. This restricts the level of
comfort provided by the automatic climate
control system. This may cause the
windows to mist up, for example.
When cooling operates, condensation
forms and drips from the underside of the
vehicle.
To return to cooling operation: press
ECO button. ECO goes out.
Picture no: 16504s.tif
Air distribution
Press one or more of the following buttons.
The corresponding symbol appears in the
air conditioning display:
To return to automatic mode: Press the
appropriate buttons again, or press AUTO.
Picture no: 16505s.tif
Air flow
Set air flow using the right-hand rotary
knob. The selected fan speed is indicated
by the number of bars.
To deactivate the fan and thereby the
automatic climate control system: Turn the
right-hand rotary knob anticlockwise until
the display goes out.
Switching on: turn rota ry knob clockwise.
To return to automatic mode: Press
AUTO button.
sAir distribution towards windscreen
and front door windows.
M Air distribution towards vehicle
occupants via adjustable vents.
K Air distribution towards footwell.

129
Driving and operation
Driving and operation
Manual transmission
automated
3
The manual transmission automated
transmission 3 permits manual ( manual
mode ) or automatic gear shifting
(automatic mode ), both with automatic
clutch control.
Picture no: 17878s.tif
Transmission display
Shows the mode and current gear.
If the Winter programme is activated, T is
illuminated.
Manual transmission automated
3... 129
Manual transmission ........................... 134
Driving hints ......................................... 135
Saving fuel, protecting the environment ...................................... 137
Fuels, refuelling .................................... 139
Catalytic converter, exhaust gasses .. 142
Drive Control Systems ......................... 146
Hydraulic brake system ...................... 151
Anti-lock brake system (ABS u ) ........ 152
Hand brake .......................................... 153
Brake assist .......................................... 153
Hill Start Assist 3 (HSA) ...................... 153
Wheels, tyres ........................................ 153
Roof rack 3.......................................... 158
Towing equipment 3........................... 158
Towing equipment with removable coupling ball bar 3........................... 159
Caravan/trailer towing ........................ 162

130 Driving and operation
Picture no: 18386s.tif
Starting the engine
When starting the engine, activate the
footbrake at the same time. The engine
can only be started in position N and with
the footbrake activated. The transmission
display shows "N". If the footbrake is not
activated, the control light j 3 in the
instrument panel illuminates and "N"
flashes in the transmission display, the
engine cannot be started.
If no brake lights are operational, the
engine will not start.
Picture no: 14175s.tif
Operation of manual transmission
automated using selector lever
Always move the selector lever all the way
to the stop. Note the gear or mode
indicator in the transmission display.
Move selector lever toward N
Neutral. Selector lever in
o (centre position)
Once the selector lever has been moved
from N to position o (centre position) with
the foot brake operated, the Easytronic is
in automatic mode and first gear has been
selected (second gear with winter
programme enabled). "A" appears in the
transmission display.
When the foot brake is released the vehicle
starts to "creep". If the foot brake is not
operated, "A" flashes. Start off by pressing
the accelerator immediately or more
selector lever back to N and repeat
procedure with foot brake operated.
In Automatic mode, selection of other
gears is automatic irrespective of driving
conditions.