2009 OPEL CORSA towing

55
Seats, Interior
Picture no: 18279s.tif
5-door passenger vehicle
Lift the cover backwards as shown in the
illustration, until it unlatches, then remove.
Fit in reverse order.
Picture no: 18414s.tif
3-door passenger vehicle
Lift the cover backwards as shown in
figure 18414 S, until it unlatches, set at
an angle, then remove.
Fit in reverse order.
Picture no: 18415s.tif
Stowing
When the luggage compartment is fully
loaded, stow the luggage compartment
cover behind the rear seat backrests:
Lift the cover backwards as shown in
figure 18415 S, until it unlatches, then slide
down in guides behind the seat backrests.
Back to overview

110 LightingShort turn signal 3
Push stalk until you feel resistance and
release. The turn signal flashes three times,
e.g. for changing lanes. This function can
be activated or deactivated depending on
the key that is used, see "personalised key",
P3 339, 341.
Acoustic turn signal 3
The volume of the acoustic turn signal can
be adjusted. This function can be
programmed depending on the key used,
see "Personalised key", P7 339, 341.
Picture no: 18199s.tif
Fog lamps
> 3

The fog lamps can only be switched on
when both the ignition and lights are on.
Operated with the > button.
Fog tail lamp
r
The fog tail lamp can only be switched on
both the ignition and dipped beam/parking
lamps are on.
Operated with the r button.
The vehicle fog tail lamp are deactivated
when towing.
Reversing lamps The reversing lamps come on when the
ignition is on and reverse gear is engaged.
Back to overview

136 Driving and operationDriving and operation
Manual transmission automated
3
The Easytronic transmission permits
manual (manual mode ) or automatic gear
shifting ( automatic mode ), both with
automatic clutch control.
Picture no: 18432s.tif
Transmission display
Shows the mode and current gear.
The display flashes for a few seconds if A,
M or R is activated with the engine running
and no foot brake applied.
Manual transmission automated
3... 136
Manual transmission ........................... 144
Automatic transmission 3.................. 144
Driving hints ......................................... 149
Saving fuel, protecting the environment ................................ 151
Fuels, refuelling .................................... 153
Catalytic converter, exhaust gasses .. 155
Drive Control Systems ......................... 159
Hydraulic brake system ...................... 165
Anti-lock brake system (ABS u ) ........ 166
Hand brake .......................................... 167
Brake assist 3...................................... 167
Hill Start Assist 3 (HSA) ...................... 167
Wheels, tyres ........................................ 168
Roof rack 3.......................................... 173
Flex-Fix system 3................................. 174
Towing equipment 3........................... 184
Caravan/trailer towing ........................ 187
Back to overview

143
Driving and operation
Picture no: 18308s.tif
Interruption of power supply
The clutch is not disengaged if there is an
interruption of the power supply when a
gear is engaged. The vehicle cannot move.
If the battery is flat, start the car using
jump leads 3191. If the cause of the power supply
interruption is not a flat battery, contact a
workshop for assistance. If the vehicle has
to be moved out of flowing traffic,
disengage clutch as follows:
1. Apply hand brake and switch off
ignition.
2. Open bonnet and engage support.
3. Clean transmission around the cap (see Fig.) so that no dirt can get into
the opening when the cap is removed.
4. Rotate cap to slacken and remove by lifting upwards – see figure.
5. Turn the adjusting screw clockwise using a flathead screwdriver (vehicle
tools 3 3198) until clear resistance can
be felt. The clutch has now been
disengaged. 6. Fit cleaned cap again. The cap must be
in full contact with the housing.
Contact a workshop for assistance
immediately.
Caution
Do not turn any further after feeling
resistance, since this can damage the
manual transmission automated.
Caution
Towing the vehicle and starting the
engine is not permitted when the clutch
has been released in this way, although
the vehicle can be moved a short dis-
tance.
Back to overview

155
Driving and operation
Picture no: 17199t.tif
Catalytic converter, exhaust
gassesCatalytic converter
The catalytic converter reduces the
amount of harmful substances in the
exhaust gas, such as carbon monoxide
(CO), hydrocarbons, CH) and nitrous
oxide (NO
x).
Fuel grades other than those listed on
pages 153, 252 (e. g. LRP = Lead
Replacement Petrol or leaded fuel) could
damage the catalytic converter or
electronic components. z
In the event of misfiring, uneven engine
running, a clear reduction in engine
performance or other unusual problems,
have the cause of the fault rectified by a
workshop as soon as possible. In an
emergency, driving can be continued for
a short period, keeping vehicle speed
and engine speed low.
This does not apply when the Electronic
Stability Program (ESP®
Plus
3) kicks in
3 151.
z If unburnt fuel enters the catalytic
converter of a petrol engine, this may
result in overheating and irreparable
damage to the catalytic converter.
You should therefore avoid
unnecessarily long use of the starter
when starting off, running the tank dry
and starting the engine by pushing or
towing.
Picture no: 18182s.tif
Controlling exhaust emission
Design measures, primarily in the fuel
injection system and ignition system zones
in combination with the catalytic converter,
the amount of hazardous substances in the
exhaust emissions, such as carbon
monoxide (CO), hydrocarbons (CH) and
nitrogen oxides (NO
x), are reduced to a
minimum.
Caution
Damage to the catalytic converter or the
vehicle may result if the following points
are not observed.
Back to overview

163
Driving and operation
To deactivateThe system deactivates automatically
when reverse gear is disengaged.
If the system is switched of with reverse
gear engaged, press button r 3, the LED
in the button goes out.
To reactivate, press button r again.
Picture no: 18255s.tif
Control indicator
r
Illuminates:
Fault in system. The system is not
operational. Have cause of fault remedied
by a workshop. The system’s integrated
self diagnostics allows faults to be quickly
remedied.
Flashes:
The fault is due to sensors obstructed with
snow or ice. The sensors must be
undamaged and free of dirt, snow and ice.
Interference due to external sources of
ultra sound (e.g. pneumatic drills, rotary
machines). Once the source of interference
is removed, the system will operate
normally. Caravan/trailer towing equipment
3,
caravan/trailer towing When towing, park pilot is automatically
deactivated when the trailer cable is
plugged into the socket.
Fitting rear load racks
3
Rear carriers, e. g. bike carriers, could
cause system malfunction.
Back to overview

165
Driving and operation
Picture no: 17206t.tif
Hydraulic brake system The foot brake comprises two independent
brake circuits.
If a brake circuit fails, the vehicle can still be
braked using the other brake circuit.
However, the brake pedal must be
depressed a considerable way before any
braking effect occurs, and much more
force is required. The braking distance is
longer. Contact a workshop for assistance
before continuing to drive. To ensure that full
pedal travel can be
utilised, especially in case of a fault in one
of the brake circuits, there must be no mats
in the vicinity of the pedals 3150.
When the engine is not running, the
support of the brake servo unit disappears
once the brake pedal has been depressed
once or twice. Braking effect is not
reduced, but braking requires significantly
greater force. This is especially important
to bear in mind when towing.
The brake fluid level should be checked
regularly. If the brake fluid level is too low
and the hand brake is not applied, control
indicator R on the instrument panel
illuminates 389.
Picture no: 18257s.tif
Brake system control indicator R
The control indicator lights up when the
ignition is switched on when the hand
brake is applied or when the brake or
clutch fluid level is too low. Brake fluid
level 3246.
For vehicles with manual transmission
automated 3, the control indicator flashes
for a few seconds when the ignition is
turned off when the hand brake is not
applied.
9
Warning
If the control indicator illuminates when
the hand brake is released, stop driving
immediately. Contact a workshop for
assistance.
Back to overview

184 Driving and operationTowing equipment
3
Only use towing equipment that has been
approved for your vehicle. Ask a workshop
to retrofit towing equipment. It may be
necessary to make changes that affect the
cooling system, heat shields or other
equipment.
Mounting dimensions of towing equipment
3269.
Stowage of coupling ball bar
The coupling ball bar is stowed in a bag in
the spare wheel well and secured to the
lashing eyes in the luggage compartment
3 187.
Picture no: 18389s.tif
Fitting the coupling ball bar
Push both bolts inwards and remove the
cover on the bumper.
Picture no: 18390s.tif
Fold down socket. Pull sealing plug out of
coupling ball bar opening. Place cover and
coupling ball bar in luggage compartment.
Caution
The coupling ball bar is to be removed
when not towing.
Back to overview