2009 OPEL CORSA door lock

40 Keys, doors, windows, sun roofProgrammable functions
The vehicle-specific functions P1 to P7
listed in the following table can be
activated and deactivated.
The setting selected is automatically stored
depending on the vehicle key used.
Different settings are stored for each
vehicle key. Use of a specific vehicle key will
activate the settings associated with it.
A total of up to five vehicle keys can be
programmed separately.
Programming permits the technical
prerequisite of the relevant function. To
activate and deactivate the functions and
set the functions, please see the relevant
sections. For page re ferences, see the
following table.
Programming:

z Turn the ignition off, the key must be in
the ignition lock,
Picture no: 18401s.tif
zPull turn signal st alk and wiper stalk
simultaneously to the steering wheel
until you hear a confirmation signal
(approx. 3 seconds),
z The kilometre display shows P1,
Picture no: 18411s.tif
zPush the turn signal stalk (left) up
or down and select the desired
function P1- P7 , see the following table,
Back to overview

41
Keys, doors, windows, sun roof
Picture no: 18412s.tif
z Push the wiper stalk (right) up or down
and select status On or OFF , or input a
value for speed (P6) or value for volume
(P7),
z Pull turn signal stalk (left) and wiper stalk
(right) simultaneously to the steering
wheel until you hear a confirmation
signal (approx. 3 seconds).
The selected settings are now stored for the
key in the ignition lock. To activate and
deactivate the functions and set the
functions selected, please see the relevant
sections. For page references, see the
following table.
Repeat the procedure to program
additional keys.
Overview of programmable functions
Function
designation Function
Status ex works Description
P 1 Switch on the extern al lighting using the
remote control (lead-me-to-the-car
lighting function) OFF
3113
P 2 Automatic rear windscreen wiper when
reverse gear is selected OFF
313
P 3 Lane change indication: three flashes
when the lever is moved slightly On
311
P 4 Automatic locking OFF334
P 5 3
Selective unlocking OFF333
P 6 Speed warning OFF392
P 7 Volume of the acoustic turn signal 3 3110
Back to overview

49
Seats, Interior
Picture no: 18161s.tif
Adjust height of seat 3
Operate lever on the door side of seat.
Pump action of lever
Picture no: 18480s.tif
Tilting the backrests forward 3
To tilt the backrests forward, lift release
lever and tilt backrest forward. Lower
release lever and backrest engages in
lowered position 3. Slide seat forwards 3.
To push the seat back to upright, it
engages in its original position 3 . Lift the
locking lever 3, move the backrest back to
upright, lower the locking lever, backrest
engages.
Folding the backrest forwards is possible
only when the backrest is in an upright
position.
Do not operate handwheel to adjust
backrest with backrest tilted forward.
Picture no: 18465s.tif
Tilting backrests forward, Corsa OPC
Remove seat belt from belt mount on
backrest.
To tilt the backrest forward, pull
release lever on rear of backrest and
tilt backrest forward. Release the release
lever andbackrest engages in the lowered
position 3. Slide seat forward 3.
To move the backrest upright, slide seat
back and it will engage in its original
position 3. Pull release lever 3, move
backrest upright, release the release lever,
backrest engages.
Folding the backrest forwards is possible
only when the backrest is in an upright
position.
Do not operate handwheel to adjust
backrest with backre st tilted forward.
Upwards = Seat higher
Downwards = Seat lower
Back to overview

77
Seats, Interior
Picture no: 18298s.tif
The system for deactivation of the airbag
systems for the front passenger can be
identified from the sticker on the side of the
instrument panel, visible when the front
passenger door is open. Fault
The front and side airbag system
3 for the
front passenger cannot be activated or
deactivated if
z the ignition is switched off,
z the engine is running,
z the vehicle is in motion,
z the time limit of 15 seconds is exceeded
when the ignition has been switched on,
z the button * is released before the
confirmation buzzer is heard,
z the time limit of 4 seconds is exceeded
after hearing the confirmation buzzer
and button * is kept depressed,
z there is a fault in the airbag system,
z the central locking button is pressed
inside the vehicle at the same time.
In these cases, a warning signal sounds
and the original setting remains
unchanged. The system remains in its
original mode. Rectify the cause, if
possible. Turn the ignition off and then
back on, and repeat the process. Important
z
Placing accessories and objects in the
expansion region of the airbag systems
is not permitted due to the risk of injury if
the components are triggered.
z There must be no objects between the
airbag systems and the occupants, risk
of injury. No child restraint system 3 may
be fitted on the front passenger seat
when the airbag systems are active,
could result in fatalities.
z Use the hooks 3 on the handles in the
roof frame only to hang up light articles
of clothing without co at hangers. Do not
place any objects in the pockets of the
hanging items, risk of injury.
z The airbag system and belt tensioner
control electronics can be found in the
centre console area. In order to avoid
malfunctions, do not store magnetic
objects in this area.
6
9
Warning
When using child restraint systems on
the front passenger seat, the airbag
system for the front passenger must be
deactivated; otherwise triggering of the
front or side airbag system 3 could
result in the death of the child.
This is particularly true for the fitting of
rear-facing child restraint systems on
the front passenger seat.
9
Warning
As with any other object, child restraint
systems must not be carried on a pas-
senger’s lap. Danger to life.
Back to overview

113
Lighting
Picture no: 18302s.tif
Lead-me lighting
3
The dipped beam remains switched on for
approx. 30 seconds once you have left the
vehicle and closed the driver’s door.
To activate
1. Switch off ignition.
2. Remove ignition key.
3. Open driver’s door.
4. Pull turn signal stalk toward steering wheel.
5. Close driver’s door.
If the driver’s door is left open, the lamps
will go out after two minutes.
The light is switched off immediately by
inserting the key into the ignition or pulling
the turn signal stalk towards the steering
wheel again.
Picture no: 18420s.tif
Switching on the exterior lighting
with the remote control
3
The lead-me-to-the-car light function
switches the dipped beam on for
approx. 30 seconds.
Program function
This function can be activated and
deactivated depending on the key used,
see "Personalised key", P1 339 341. To activate
Press button
q on the remote control twice
when the vehicle is locked.
Country-specific application 3: To switch
on the Lead-me-to-the-car light function,
press button q on the remote control once
the vehicle is locked.
Switching on the ignition or pressing
button p on the remote control will
deactivate the Lead-me-to-the-car light
function early.
Back to overview

114 Lighting
Picture no: 18370s.tif
Parking lamps The front parking lamp and tail lamp of
one side of the vehicle can be activated
when parking:
1. Set light switch to 7 or A 3,
2. Ignition off,
3. Move turn signal stalk all the way up (right parking lamp) or down (left
parking lamp).
Confirmed by a signal and the
corresponding turn signal control indicator.
To switch it off, swit ch on the ignition or
move the turn signal stalk in the opposite
direction.
Picture no: 18201s.tif
Instrument illumination
,
Information display illumination

Lights come on when ignition is switched
on.
Adjustable brightness when exterior
lighting is switched on:
Hold down the button until the required
brightness is achieved.
Display mode 33100.
Courtesy lamp Automatic interior light
Comes on automatically when the vehicle is
unlocked with the remote control, when a
door is opened or when the key is removed
from the ignition switch after the ignition is
switched off.
Goes off automatically after a delay when
the doors are closed or immediately when
the ignition is switched on or the doors are
locked.
Brighter = Push button +
Darker = Push button -
Back to overview

125
Climate control
Picture no: 18211s.tif
Heating the foot well
zRotate temperature switch to right-hand
zone.
z Switch on fan.
z Set air distribution switch to K.
Picture no: 18212s.tif
Window demisting and de-icing
Misted or icy windows, e. g. due to damp
weather, damp clothing or low outside
temperatures: z
Turn the temperature switch clockwise as
far as it will go (warm).
z Move fan switch to 3 or 4.
z Move air distribution switch to l.
z To heat footwell at same time, move air
distribution switch to J.
z Open side air vents as required and
direct them towards door windows.
z Switch on heated rear window Ü.
9
Warning
Disregard of the instructions could lead
to misting or icing of the windows and
subsequent accidents due to impaired
visibility.
Back to overview

128 Climate control
Picture no: 18217s.tif
Window demisting and de-icing
Misted or icy windows, e. g. due to damp
weather, damp clothi ng or low outside
temperatures: z
Cooling n on, the air conditioning
compressor automatically switches itself
off at low outside temperatures (icing).
z Turn the temperature switch clockwise.
z Move fan switch to 4.
z Move air distribution switch to l.
z Open side air vents as required and
direct them towards door windows.
z Switch on heated rear window Ü.
Electronic climate control system
3
Provides a the greatest amount of comfort
in the interior regardless of the weather,
outside temperature or season.
To ensure a constant and comfortable
climate in the vehicle, the temperature of
the inflowing air, the air-flow rate and the
air distribution are changed automatically
according to climatic conditions outside
the vehicle.
The climate is regulated automatically
based on personal settings.
Temperature changes due to external
influences, such as direct sunlight, are
automatically compensated.
9
Warning
Disregard of the inst ructions could lead
to misting or icing of the windows and
subsequent accidents due to impaired
visibility.
Back to overview