2009 NISSAN LATIO bulb

Bulb Replacement " .
Removal and Installation INFOID:0000000004306621
PARKING LAMP
Refer to LT-87, " Removal and Installation " .
LICENSE PLATE LAMP-HATCHBACK
Removal
1. Press the license plate lamp pawl on the side of t he rear bumper fascia, then swing the license plate lamp
down to release the license plate lamp hook from the rear bumper fascia.
2. Disconnect the license plate lamp connector and remove the licence plate lamp.
Installation
Installation is in the reverse order of removal.
LICENSE PLATE LAMP-SEDAN
Removal
1. Remove the license plate lamp finisher. Refer to EI-55, " Removal and Installation " .

Removal and Installation " .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
4. Installation is in the reverse order of removal.
SEDAN
1. Remove trunk side finisher. Refer to EI-55, " Removal and Installation " .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove the stop/tail lamp bulb (1), turn signal lamp bulb (2), and the back-up lamp bulb (3).
4. Installation is in the reverse order of removal.

LT
N
O P
Removal and Installation
INFOID:0000000004306624
HATCHBACK
Removal 1. Remove rear combination lamp nuts.
2. Pull the rear combination lamp toward rear of the vehicle and remove from the vehicle.
3. Disconnect rear combination lamp connector, and remove rear combination lamp.
Installation Installation is in the reverse order of removal.
SEDAN
Removal 1. Remove trunk side finisher. Refer to EI-53, " Removal and Installation " .
2. Remove the rear combination lamp nuts (1).
3. Remove the rear combination lamp (2).
4. Remove the rear combination lamp seal (3).
Installation Installation is in the reverse order of removal.
Disassembly and Assembly INFOID:0000000004306625
DISSASEMBLY 1. Remove the rear combination lamp harness.
2. Remove the bulbs from the rear combination lamp harness, as necessary.
3. Remove the bumper stay (hatchback only).
4. Remove the rear combination lamp seal (sedan only).
ASSEMBLY Assembly is in the reverse order of disassembly.

LT
N
O P
1. Remove luggage compartment lamp from the luggage side finisher LH.
2. Remove luggage compartment lamp cover.
3. Press tab A and remove the bulb.
4. Installation is in the reverse order of removal.
REMOVAL AND INSTALLATION
Removal 1. Remove luggage compartment lamp from the luggage side finisher LH.
2. Disconnect luggage compartment lamp connector.
Installation Installation is in the reverse order of removal.
Trunk Room Lamp, Sedan INFOID:0000000004609544
BULB REPLACEMENT 1. Press the tab and open the cover.
2. Remove the bulb.
REMOVAL AND INSTALLATION
Removal 1. Flex the tab and separate the trunk room lamp from the panel.
2. Disconnect the electrical connector and remove the lamp.
Installation Installation is in the reverse order of removal.
Vanity Mirror Lamp INFOID:0000000004609545
BULB REPLACEMENT 1. Luggage compartment lamp bulb cover 2. Luggage compartment lamp A. Tab A

LT
N
O P
1. Map lamp switch is in OFF position.
2. Check voltage between map lamp harness connector R2 termi- nal 4 and ground.
OK or NG OK >> GO TO 5.
NG >> Repair harness or connector. OK >> Replace map lamp.
NG >> Repair harness or connector. OK >> GO TO 7.
NG >> Check bulb. If OK, replace interior room lamp. OK >> GO TO 8.
NG >> Replace map lamp.

LT
N
O P
1. Disconnect room lamp connector.
2. Check continuity between room lamp terminals.
OK or NG OK >> GO TO 5.
NG >> Check bulb. If OK, replace room lamp. Refer to LT-105, " Bulb Replacement " .
OK >> GO TO 6.
NG >> Repair harness or connector. OK >> Replace BCM if interior lamp does not work after setting
the connector again. Refer to BCS-18, " Removal and
Installation of BCM " .
NG >> Repair harness or connector.
Bulb Replacement INFOID:0000000004306638
ROOM LAMP 1. Remove lens (1) by inserting suitable tool and releasing LH (switch side first).
2. Remove bulb (2).
3. Installation is in the reverse order of removal. NOTE:
Insert the lens hook end RH side first to install lens.
Removal and Installation INFOID:0000000004306639
ROOM LAMP Room lamp
Condition Continuity
Terminal
2 3 Room lamp switch is in
DOOR position Yes
Room lamp switch is in OFF
position No

LT
N
O P
Bulb Replacement INFOID:0000000004306644
GLOVE BOX LAMP 1. Remove glove box assembly. Refer to IP-11 . B

LT
N
O P
BULB SPECIFICATIONS
Headlamp INFOID:0000000004306645
Exterior Lamp INFOID:0000000004306646
Interior Lamp/Illumination INFOID:0000000004306647
* Always check with the parts department for the latest parts information. Item Wattage (W)
High/Low (Halogen type) 60/55Item Wattage (W)
Front combination lamp Turn signal lamp 21 (amber)
Parking (clearance) lamp 5
Rear combination lamp Stop/Tail lamp 21/5
Turn signal lamp 21 (amber)
Back-up lamp 21
Front fog lamp 35 (H8)
License plate lamp 5
High-mounted stop lamp Hatchback LED
Sedan, rear window 18
Sedan, rear spoiler LED Item Wattage (W)
Glove box lamp 1.4
Map lamp 8
Room lamp 8
Luggage room lamp (Hatchback) 5
Trunk room lamp (Sedan) 5
Vanity mirror lamp *