2009 NISSAN GT-R brake

Black plate (248,1)
Model "R35-D" EDITED: 2008/ 5/ 20
For further brake fluid information, see the
following section. (
“CAPACITIES AND
RECOMMENDED FUEL/LUBRICANTS” page
9-2)
WARNING
. Use only new fluid from a sealed
container. Old, inferior or contami-
nated fluid may damage the brake
system. The use of improper fluids
can damage the brake system and
affect the vehicle’s stopping ability.
. Clean the filler cap before removing.
. Brake fluid is poisonous and should
be stored carefully in marked con-
tainers out of the reach of children.
CAUTION
Brake Fluid R35 Special DOT4 is the
factory fill brake fluid. The Vehicle
Dynamic Control (VDC) unit and other
related parts were specially designed
for this brake fluid and NISSAN cannot
ensure the best performance and prop-
er operation of the vehicle if other
brake fluid is used.
NOTICE
Do not spill the fluid on any painted
surfaces. This will damage the paint. If
fluid is spilled, wash the surface with
water.
Check the fluid level in the reservoir. If the fluid is
below the MIN line
*1
or the brake warning
light comes on, add Genuine NISSAN Brake
Fluid R35 Special DOT4 fluid up to the MAX line
*2. If fluid must be added frequently, the
system should be checked by a GT-R certified
NISSAN dealer.
8-14
Maintenance and do-it-yourself
BRAKE FLUID
,QIRUPDWLRQ3URYLGHGE\

Black plate (252,1)
Model "R35-D" EDITED: 2008/ 5/ 20
replaced or adjusted by a GT-R certified
NISSAN dealer.
2. Have the belts checked regularly for condi- tion and tension in accordance with the
maintenance schedule in your “NISSAN
Service and Maintenance Guide”.
WARNING
Be sure the engine and the ignition
switch are off and that the parking
brake is engaged securely.
NOTICE
Be sure to use the correct socket to
remove the spark plugs. An incorrect
socket can damage the spark plugs.
REPLACING SPARK PLUGSIf replacement is required, see a GT-R certified
NISSAN dealer for servicing.Iridium-tipped spark plugsIt is not necessary to replace the iridium-tipped
spark plugs as frequently as the conventional
type spark plugs since they will last much longer.
Follow the maintenance schedule in “NISSAN
Service and Maintenance Guide”, but do not
reuse them by cleaning or regapping.
Always replace spark plugs with recom-
mended or equivalent ones.
8-18
Maintenance and do-it-yourself
SPARK PLUGS
,QIRUPDWLRQ3URYLGHGE\

Black plate (254,1)
Model "R35-D" EDITED: 2008/ 5/ 20
REPLACING THE WIPER BLADESReplace the wiper blades if they are worn.
1. Pull the wiper arm.
2. Push the release tab
*A
, and then move the
wiper blade down the wiper arm
*1
while
pushing the release tab to remove.
3. Insert the new wiper blade onto the wiper arm until a click sounds.
4. Rotate the wiper blade so the dimple is in the groove.
NOTICE
.After wiper blade replacement, re-
turn the wiper arm to its original
position; otherwise it may be da-
maged when the hood is opened.
. Make sure the wiper blades contact
the glass; otherwise the arm may be
damaged from wind pressure.
If the brakes do not operate properly, have the
brakes checked by a GT-R certified NISSAN
dealer.SELF-ADJUSTING BRAKESYour vehicle is equipped with self-adjusting
brakes.
The disc-type brakes self-adjust every time the
brake pedal is applied.
WARNING
See a GT-R certified NISSAN dealer for
a brake system check if the brake pedal
height does not return to normal.BRAKE PAD WEAR INDICATORSThe disc brake pads on your vehicle have
audible wear indicators. When a brake pad
requires replacement, it will make a high pitched
scraping or screeching sound when the vehicle
is in motion. This scraping sound will first occur
only when the brake pedal is depressed. After
the wear of brake pad is increased, the sound
will be heard all the time even if the brake pedal
is not depressed. Have the brakes checked as
soon as possible if the wear indicator sound is
heard.
Under some driving or climate conditions,
occasional brake squeak, squeal or other noise
may be heard. Occasional brake noise during
8-20
Maintenance and do-it-yourself
BRAKES
,QIRUPDWLRQ3URYLGHGE\

Black plate (255,1)
Model "R35-D" EDITED: 2008/ 5/ 20
light to moderate stops is normal and does not
affect the function or performance of the brake
system.
Proper brake inspection intervals should
be followed.For additional information, see the
maintenance log section of your “NISSAN
Service and Maintenance Guide” for mainte-
nance intervals.HIGH PERFORMANCE BRAKE SYS-
TEMThis vehicle is equipped with high performance
brake pads that provide appropriate braking
force in a broad range of driving environments.
Due to the material used for the brake pads, the
road wheels may become more easily covered
by brake dust, however this does not indicate
that there is a malfunction.
Frequent hard braking may cause scorching of
the brake pads. This will require the brake pads
to be replaced, even if the wear limit has not
been reached. Have the brake pads and disc
rotors inspected at the regular vehicle inspec-
tions.
For more details, contact a GT-R certified
NISSAN dealer.
REPLACING THE BRAKE PADSTo ensure maximum performance, the brake
pads and disc rotors must be replaced as a set.
Never replace or use only the brake pads on
their own. When replacement is required, we
recommend seeing a GT-R certified NISSAN
dealer for servicing.NOTE:. This vehicle is equipped with a high
performance braking system and in-
cludes cross-drilled floating rotors and
radial-mounted six-piston monoblock
calipers. This helps to achieve excellent
stopping performance and fade-resis-
tance. Replace all four sets of brake
pads and disc rotors at the same time
to maintain maximum brake perfor-
mance.
. To maintain steady braking perfor-
mance in both extremely high and low
temperatures, the gap between the
brake pad and caliper is larger than
normal and large-size brake pads are
used. When driving over a bump, a light
rattling sound may be heard from the
brake pad. This does not indicate that
there is a malfunction. .
When the brake disc rotor undergoes
thermal expansion, a rumbling noise
may be heard from the engaging por-
tion of the wheel and the brake disc
rotor. This does not indicate that there
is a malfunction. The noise will cease
when the temperature decreases.
Maintenance and do-it-yourself
8-21
,QIRUPDWLRQ3URYLGHGE\

Black plate (272,1)
Model "R35-D" EDITED: 2008/ 5/ 20
speed rating and load carrying capacity as
originally equipped. (
“WHEELS AND
TIRES” page 9-7)
WARNING
. The use of tires other than those
specified or the mixed use of tires of
different brands, construction (bias,
bias-belted, radial or run-flat) , or
tread patterns can adversely affect
the ride, braking, VDC system, hand-
ling, ground clearance, body-to-tire
clearance, tire chain clearance,
speedometer calibration, headlight
aim and bumper height. Some of
these effects may lead to accidents
and could result in serious personal
injury.
. If the wheels are changed for any
reason, always replace with wheels
which have the same off-set dimen-
sion. Wheels of a different off-set
could cause premature tire wear,
degrade vehicle handling character-
istics, affect the VDC system and/or
cause interference with the brake
discs. Such interference can lead to
decreased braking efficiency and/or
early brake pad wear. (
“WHEELS AND TIRES” page
9-7)
. When a wheel is replaced, tire
pressure will not be indicated, the
TPMS will not function and the low
tire pressure warning light will flash
for approximately 1 minute and
remain on after the 1 minute. Con-
tact a GT-R certified NISSAN dealer
as soon as possible for tire replace-
ment and/or system resetting.
. Replacing tires with those not ori-
ginally specified by NISSAN could
affect the proper operation of the
TPMS.
. Do not install a damaged or de-
formed wheel or tire even if it has
been repaired. Such wheels or tires
could have structural damage and
could fail without warning.
. Never use retread tires.
. For additional information regard-
ing tires, refer to “Important Tire
Safety Information” (US) or “Tire
Safety Information” (Canada) in the
Warranty Information Booklet.
. Always use tires of the specified
type, size, brand, construction (bias, bias-belted, radial or run-flat) , and
tread pattern on all four wheels.
Failure to do so may result in a
circumference difference between
tires on the front and rear axles
which will cause excessive tire wear
and may damage the transmission,
transfer case and differential gears.
Wheel balanceUnbalanced wheels may affect vehicle handling
and tire life. Even with regular use, wheels can
get out of balance. Therefore, they should be
balanced as required.
Wheel balance service should be performed
with the wheels off the vehicle. Spin balancing
the rear wheels on the vehicle could lead to
mechanical damage.
For additional information regarding tires, refer
to “Important Tire Safety Information” (US) or
“Tire Safety Information” (Canada) in the War-
ranty Information Booklet.Care of wheels.
Wash the wheels when washing the vehicle
to maintain their appearance.
. Clean the inner side of the wheels when the
wheel is changed or the underside of the
vehicle is washed.
8-38
Maintenance and do-it-yourself
,QIRUPDWLRQ3URYLGHGE\

Black plate (273,1)
Model "R35-D" EDITED: 2008/ 5/ 20
.Do not use abrasive cleaners when washing
the wheels.
. Inspect wheel rims regularly for dents or
corrosion. Such damage may cause loss of
pressure or poor seal at the tire bead.
. NISSAN recommends that the side walls of
road wheels be waxed to protect against
road salt in areas where it is used during
winter.JACKING VEHICLE AND REMOVING
WHEELS
WARNING
.Make sure the parking brake is
securely applied and the transmis-
sion is shifted into the
&Pposition.
. Never change tires when the vehicle
is on a slope, ice or slippery areas.
This is hazardous.
. Never change tires if oncoming
traffic is close to your vehicle. Wait
for professional road assistance.
Blocking wheelsPlace suitable blocks
*1
at both the front and
back of the wheel diagonally opposite the flat
tire to prevent the vehicle from moving when it is
jacked up.
WARNING
Be sure to block the wheel as the
vehicle may move and result in personal
injury.
Getting the toolsNOTE:A jack, jack lever and rod are not equipped
as standard with this vehicle. These parts
are dealer options. Contact a GT-R certi-
fied NISSAN dealer about acquiring a jack,
jack lever and rod. You can store a jack,
jack lever and rod in the floor in front of
the passenger’s seat.
CAUTION
After using the tools, put them back in
their original places. An accident may
occur if you leave them in the car
Maintenance and do-it-yourself
8-39
,QIRUPDWLRQ3URYLGHGE\

Black plate (276,1)
Model "R35-D" EDITED: 2008/ 5/ 20
5. Remove the wheel nuts and then remove thewheel.NOTE:When putting a wheel on the ground, put it
down with the outer side of the wheel
facing up to prevent scratching of the
wheel surface.
6. Clean any mud or dirt from the surfacebetween the brake disc rotor
*1
and wheel
*2.
7. Tighten the wheel nuts by hand by turningthem clockwise until the tapered part
*A
of
each nut lightly contacts the seat part
*B
of
the wheel hole.
When replacing a front wheel, make sure the
hole in the wheel is aligned with the pin on
the brake disc rotor.
8-42
Maintenance and do-it-yourself
,QIRUPDWLRQ3URYLGHGE\

Black plate (280,1)
Model "R35-D" EDITED: 2008/ 5/ 20
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure
instructed in the “8. Maintenance and do-it-yourself” section to determine the proper refill capacity.
Capacity (Approximate)Recommended specifications
US measure Imp measure Liter
Fuel 19-1/2 gal 16-1/4 gal 73.8 Unleaded gasoline with an octane rating of at least 93 AKI (RON 98)*1
Engine oil*4
Mobil 1, 0W-40*2
Drain and refill
With oil filter change 5-7/8 4-7/8 5.5
Without oil filter change 5-1/4 4-3/8 5.0
Cooling system With reservoir 11-5/8 9-5/8 11.0 Genuine NISSAN Long Life Antifreeze/Coolant or equivalent*7
Reservoir 1-1/2 1-1/4 1.4
Transmission oil — — — Genuine NISSAN Transmission Oil R35 Special*3
Differential oil (front and rear) — — — Castrol SAF-XJ 75W-140*3
Power steering fluid (PSF) Refill to the proper oil level according to the instructions in the “8.
Maintenance and do-it-yourself” section. Genuine NISSAN PSF or equivalent*6
Brake fluid Genuine NISSAN Brake Fluid R35 Special DOT4*8
Multi-purpose grease — — — NLGI No. 2 (Lithium soap base)
Air conditioning system refrigerant — — — HFC-134a (R-134a)*5
Air conditioning system lubricants — — — NISSAN UV Luminous Oil
Type S or exact equivalent
Window washer fluid — — — Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent
*1: For additional information, see the following section. (
“FUEL RECOMMENDATION” page 9-3)
*2: Mobil 1, 0W-40 (100% synthetic) is the factory fill oil. The VR38 engine with its plasma-sprayed bores was developed using this oil. NISSAN cannot ensure proper engine operation and durability if other 0W-40 synthetic oil is used. If Mobil 1, 0W-40 is not available, Mobil 1, 10W-40 (100% synthetic) may be used; however, some performance loss may be noticed. For additional information, see the following section.
(
“ENGINE OIL AND OIL FILTER RECOMMENDATION” page 9-4)
*3: The use of fluids and lubricants other than the specified may cause vehicle malfunctions and result in non-warranty vehicle repairs.
*4: For additional information, see the following section. (
“ENGINE OIL” page 8-12)
*5: For additional information, see the following section. (“AIR CONDITIONER SPECIFICATION LABEL” page 9-10)
*6: DEXRON
TMVI type ATF or Canada NISSAN Automatic Transmission Fluid may also be used.
*7: For additional information, see the following section. (
“ENGINE COOLING SYSTEM” page 8-9)
*8: Genuine NISSAN Brake Fluid R35 Special DOT4 is the factory fill brake fluid. The Vehicle Dynamic Control (VDC) unit and other related parts were specially designed for this brake fluid and NISSAN cannot ensure the best performance and proper operation of the vehicle if other brake fluid is used.
9-2
Technical and consumer information
CAPACITIES AND RECOMMENDED
FUEL/LUBRICANTS
,QIRUPDWLRQ3URYLGHGE\