2009 NISSAN GT-R start stop button

Black plate (115,1)
Model "R35-D" EDITED: 2008/ 5/ 20
How to arm the vehicle security
system1. Close all windows.The system can be armed even if the
windows are open.
2. Push the ignition switch to the OFF or LOCK position.
3. Remove the Intelligent Key from the vehicle.
4. Close all doors, hood and trunk. Lock all doors. The doors can be locked with the
Intelligent Key, door handle request switch
or power door lock switch. The power door
lock switch should be operated while the
door is open, and then closed. 5. Confirm that the security indicator light
comes on. The security indicator light stays
on for about 30 seconds. The vehicle
security system is now pre-armed. After
about 30 seconds the vehicle security
system automatically shifts into the armed
phase. The security light begins to flash
once every approximately 3 seconds. If,
during this 30-second pre-arm time period,
the door is unlocked, or the ignition switch is
pushed to ACC or ON, the system will not
arm.
Even when the driver and/or passengers
are in the vehicle, the system will activate
with all doors, hood, and trunk lid locked
withtheignitionswitchintheLOCK
position. When pushing the ignition switch
to the ACC or ON position, the system will
be released.
Vehicle security system activationThe vehicle security system will give the follow-
ing alarm:
. The headlights blink and the horn sounds
intermittently.
. The alarm automatica lly turns off after
approximately 1 minute. However, the alarm
reactivates if the vehicle is tampered with
again. The alarm is activated by:
.
Unlocking the door or opening the trunk lid
without using the button on the Intelligent
Key, the door handle request switch or the
mechanical key. (Even if the door is opened
by releasing the door inside lock knob, the
alarm will activate.)
. Opening the hood.
How to stop an activated alarmThe alarm will stop by unlocking a door by
pushing the unlock button on the Intelligent Key
or the door handle request switch. The alarm will
not stop if the ignition switch is pushed to the
ACC or ON position.
If the system does not operate as de-
scribed above, have it checked by a GT-R
certified NISSAN dealer.NISSAN VEHICLE IMMOBILIZER
SYSTEMThe NISSAN Vehicle Immobilizer System will not
allow the engine to start without the use of the
registered Intelligent Key. Never leave these
keys in the vehicle.
Statement related to section 15 of FCC
rules for NISSAN Vehicle Immobilizer
System (CONT ASSY - CARD SLOT)
This device complies with part 15 of the
Instruments and controls
2-43
,QIRUPDWLRQ3URYLGHGE\

Black plate (178,1)
Model "R35-D" EDITED: 2008/ 5/ 20
WARNING
Do not operate the push-button ignition
switch while driving the vehicle except
in an emergency. (The engine will stop
when the ignition switch is pushed
three consecutive times or the ignition
switch is pushed and held for more than
2 seconds.) If the engine stops while
the vehicle is being driven, this could
lead to a crash and serious injury.
Before operating the push-button ignition
switch, be sure to move the shift lever to the&Pposition.
OPERATING RANGE FOR ENGINE
STARTThe operating range for starting the engine
inside the vehicle is shown in the illustration.
. If the Intelligent Key is on the instrument
panel, rear parcel shelf, inside the glove box
or door pocket, or the corner of interior
compartment, it may not be possible to start
the engine.
. If the Intelligent Key is near the door or door
glass outside the vehicle, it may be possible
to start the engine.
IGNITION SWITCH OPERATIONWhen the Intelligent Key is carried with you and
the ignition switch is pushed without depressing
the brake pedal, the ignition switch position will
change as follows:
.Push center once to change to ACC.
. Push center two times to change to ON.
. Push center three times to change to OFF.
(No position illuminates.)
. Push center four times to return to ACC.
. Open or close any door to return to LOCK
during the OFF position.
5-8
Starting and driving
PUSH-BUTTON IGNITION SWITCH
,QIRUPDWLRQ3URYLGHGE\

Black plate (184,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Never shift to the
&P
or
&A↔&M
position while the vehicle is moving
rearward. Doing so could cause loss
of control and an accident.
. The shift lever contains a powerful
magnet. Do not place electronic
medical devices or other electronic
products that are susceptible to
magnetic force close to the shift
lever.
CAUTION
.Do not downshift abruptly on slip-
pery roads. This may cause a loss of
control.
. Because the vehicle includes a dual
clutch transmission that automati-
cally controls the clutch and shifting
operation of the manual transmis-
sion, whenever the shift lever is in a
position other then
&P
or
&N, the
vehicle will begin to move slowly, in
the same way as when the clutch in
a manual transmission vehicle is
partially engaged. Keep the brake
pedal firmly depressed when the
vehicle is stopped. In some circum-
stances the vehicle may not start moving on its own, however this
does not indicate that there is a
malfunction.
NOTICE
When the vehicle is stopped on a hill,
do not hold the vehicle in place by
depressing the accelerator pedal. Doing
so may cause the clutch to overheat and
result in transmission damage. Use the
brakes to prevent the vehicle from
moving.
Operating the shift leverAfter starting the engine, fully depress the brake
pedal and move the shift lever from the
&P
position to the
&R,&N,or
&A↔&M
position. Push
the button to shift into the
&Por&Rposition. All
other positions can be selected without pushing
the button.
5-14
Starting and driving
,QIRUPDWLRQ3URYLGHGE\

Black plate (185,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Shift lever operation
Push the button while depressing the brake
pedal.Push the button.Just move the shift lever.Automatically returns.
&Pposition:
Use this position for parking and starting the
engine. The ignition switch will be changed to
the OFF or LOCK position.
CAUTION
Use the
&P
position only when the
vehicle is completely stopped.
&Rposition:
Use this position for driving in reverse.&Nposition:
Neither forward nor reverse gear is engaged.&A↔&M
position:
Use this position for all normal forward driving.
The shift lever can be moved between
&Aand
&M
to alternately change each other. The position indicator indicates the gear position
with the indication of “A” or “M”.
.
&A
position: Use this position for ordinary
driving, with the gears shifted automatically
from first gear to sixth gear according to the
speed and driving conditions.
.
&M
position: Operate the paddle shifter to
drive in first gear to sixth gear as desired.
CAUTION
Grip the shift lever correctly when
operating it. Failure to do so may cause
a finger or other items to be trapped
between the lever and gate, possibly
causing an accident.
NOTICE
. Be sure to observe the following
precautions. Failure to do so may
result in shift lever malfunction.
— Do not spill water, beverages or
other liquids on the shift lever.
Starting and driving
5-15
,QIRUPDWLRQ3URYLGHGE\

Black plate (189,1)
Model "R35-D" EDITED: 2008/ 5/ 20
GearMPH (km/h)
1st 35 (57)
2nd 62 (101)
3rd 90 (145)
4th —
5th —
6th —
DRIVING TIPSAfter starting the engine, fully depress the foot
brake pedal and push the shift lever button
before shifting the shift lever from the
&Pposition
to the
&R,&N,or
&A↔&M
position. Be sure the
vehicle is fully stopped before attempting to shift
the shift lever.
The transmission is designed so that the foot
brake pedal must be depressed before shifting
from
&Pto any other position.
The shift lever cannot be moved out of the
&P
position and into any other position with the
ignition switch other in the LOCK, OFF or ACC
position.When accelerating from a stopKeep the foot brake pedal depressed and push
the shift lever button to shift into a driving gear
as following:
. To drive forward, move the shift lever to the
&A↔&M
position.
. To back up, move the shift lever to the
&R
position.
Starting on level ground:1. Check the shift lever position indicator on
the instrument panel to confirm that the
driving gear is selected.
2. Release the parking brake.
3. Release the foot brake pedal, then gradually depress the accelerator pedal to start the
vehicle in motion.Starting on an uphill:1. Check the shift lever position indicator onthe instrument panel to confirm that the
driving gear is selected.NOTE:When starting or driving on a steep uphill
grade, shift to the
&M
position and operate
the paddle shifter to shift down to 1st gear
as a manual transmission vehicle.
2. With the parking brake applied, slowly release the foot brake pedal.
3. Slowly depress the accelerator pedal and feel the vehicle starting motion with the
parking brake applied.
4. Release the parking brake and gradually depress the accelerator pedal to start the
vehicle in motion.
NOTICE
To prevent stalling or transmission
damage, start in 1st gear. The
&M
position 2nd gear can be used to start
moving the vehicle only when reduced
torque is necessary on snowy roads or
extremely slippery surfaces.NOTE:The hill start assist function operates when
the vehicle is accelerating from a stop on
an uphill. (
“HILL START ASSIST” page
5-31)
When driving the vehicle
WARNING
Do not move the shift lever to the
&N
position while driving. Doing so may
result in an accident due to loss of
engine braking. It may also damage the
transmission.
Starting and driving
5-19
,QIRUPDWLRQ3URYLGHGE\

Black plate (197,1)
Model "R35-D" EDITED: 2008/ 5/ 20
prevent diminished starting perfor-
mance, avoid starting and stopping the
engine repeatedly during a short period
of time.
WARNING
.Be sure the parking brake is fully
released before driving. Failure to
do so can cause brake failure and
lead to an accident.
. Do not release the parking brake
from outside the vehicle.
. Do not use the gear shift in place of
the parking brake. When parking, be
sure the parking brake is fully
engaged.
. Do not leave children unattended in
a vehicle. They could release the parking brake and cause an acci-
dent.
To apply: Pull the parking brake lever up.
To release:
1. Firmly apply the foot brake.
2. Place the shift lever in the
&Nposition.
3. While pulling up on the parking brake lever slightly, push the button
*A
and lower the
lever completely.
4. Before driving, be sure the brake warning light goes out.
Starting and driving
5-27
PARKING BRAKE
,QIRUPDWLRQ3URYLGHGE\

Black plate (5,1)
Refueling precautions....................... GTR-7
Pregnant women ..................................... 1-9
Programming HomeLink
®.......................... 2-60
Programming HomeLink®for Canadian
customers .......................................... 2-62
Programming trouble-diagnosis ................... 2-62
Push starting ......................................... 6-6
Push-button ignition switch ......................... 5-8
“PUSH” warning ................................... 2-40
R
Rapid air pressure loss .............................. 5-6
Readiness for Inspection/Maintenance test ...... 9-16
Rear window defroster switch .................... 2-46
Refueling precautions ........................... GTR-7
Refueling stops before the tank is full .......... GTR-7
Remote keyless entry functions ................... 3-12
Removing spots ...................................... 7-3
Removing the cowl top cover ....................... 8-8
Repair and replacement procedure .............. 1-44
Replacing spark plugs ............................. 8-18
Replacing the brake pads ......................... 8-21
Replacing the wiper blades ....................... 8-20
Replenishing coolant ............................ GTR-6
Reporting safety defects .......................... 9-16
Reprogramming a single HomeLink
®button ..... 2-63
Run-flat tire warning ............................... 2-36
Run-flat tires ......................................... 6-2
S
Safety All-Wheel Drive driving safety precautions .... 5-7
Child safety ....................................... 1-7 Reporting safety defects
...................... 9-16
Scheduled maintenance ............................. 8-2
Seat Booster seat installation ....................... 1-29
Booster seats .................................. 1-27
Child restraint installation using the seat
belts ............................................. 1-21
Front seat-mounted side-impact
supplemental air bag and roof-mounted curtain
side-impact supplemental air bag system . . . 1-40
Front seats ....................................... 1-2
Heated seats ................................... 2-51
NISSAN Advanced Air Bag System .......... 1-36
Precautions on booster seats ................. 1-27
Precautions on seat belt usage ................. 1-5
Seat belt extenders ............................ 1-12
Seat belt maintenance ......................... 1-12
Seat belts .................................. 1-5, 7-5
Seat belts with pretensioners ................. 1-42
Seats .............................................. 1-2
Three-point type seat belt with retractor ....... 1-9
Seat belt Child restraint installation using the seat
belts ............................................. 1-21
Precautions on seat belt usage ................. 1-5
Seat belt extenders ............................ 1-12
Seat belt maintenance ......................... 1-12
Seat belts .................................. 1-5, 7-5
Seat belts with pretensioners ................. 1-42
Three-point type seat belt with retractor ....... 1-9
Security systems ................................... 2-42
Self-adjusting brakes .............................. 8-20
Setting (drive computer) .......................... 2-17
Setting hazard indicator and horn mode ......... 3-13
Shift “P” warning ................................... 2-40 Shift lever position warning
....................... 2-32
Spark plugs ........................................ 8-18
Special winter equipment ......................... 5-42
Specifications ........................................ 9-6
Speedometer ......................................... 2-5
Starting Before starting the engine .................... 5-11
Jump starting .............................. 6-3, 8-17
Precautions when starting and driving ......... 5-2
Push starting ..................................... 6-6
Starting the engine ............................ 5-11
Steering Power steering ................................. 5-38
Power steering fluid ........................... 8-13
Steering lock release malfunction
indicator ........................................ 2-41
Steering wheel ................................. 3-25
Steering-wheel-mounted controls ............ 5-29
Tilt/telescopic steering column ............... 3-25
Storage ............................................. 2-53
Summer tires ..................................... GTR-5
Sun visors .......................................... 3-26
Sunglasses holder ................................. 2-54
Supplemental air bag warning labels ............. 1-43
Supplemental air bag warning light .............. 1-43
Supplemental restraint system .................... 1-31
Switch Hazard warning flasher switch ................ 2-50
Headlight and turn signal switch ............. 2-47
Headlight switch ............................... 2-48
How to switch the modes ..................... 5-22
Ignition switch operation ........................ 5-8
Ignition switch positions ......................... 5-9
Interior light control switch .................... 2-59
10-5
Model "R35-D" EDITED: 2008/ 5/ 20
,QIRUPDWLRQ3URYLGHGE\