2009 NISSAN ALTIMA COUPE seats

TRUNK LID CANCEL SWITCH
When the cancel switch (located inside the glove box)
is OFF, the trunk lid cannot be opened with the trunk lid
opener (located onthe instrument panel) ,thetrunk
Request Switch button (if so equipped) or the Intelli-
gent Key button.
 It can be opened by using the Emergency Inside Trunk
Release.
MOONROOF CONTROLS (if so equipped)
The ignition switch must be in the ON position to operate
the moonroof controls.
TILTING THE MOONROOF
 To tiltthe moonroof up,push thetiltswitch toward
the
position.
 To tilt the moonroof down, push the tilt switch toward
the
position.
SLIDING THE MOONROOF
 To fully open the moonroof, push the switch toward theposition.
 To fully close the moonroof, push the switch toward the
position.
 To open orclose themoonroof partway, push theswitch ineither direction (
or) while the moonroof is sliding to stop it in the desired position.
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
FORWARD AND BACKWARD
 Pull the center of the bar up
under the front of the
seat andhold itwhile youslide theseat forward or
backward. Release the bar to lock the seat in position.
SEAT LIFTER (driver’s seat, if so equipped)
 Pull up or push down the adjusting lever
repeat-
edly to adjust the seat height.
RECLINING
 Lift the lever
on the side of the seat to adjust the seatback forward or backward.
Release thelever when youhave found acomfortable angleandtheseat beltfits
properly.
14

With power seats (if so equipped):
The control lever
allows you to make the
following adjustments.
 Move thecontrol lever
forward or
backward toadjust theseat forward or
backward.
 Pull up or press down on the front of the
control lever
to adjust the front por-
tion of the driver’s seat cushion.
 Pull uporpress downonthe rear ofthe
control lever
toraise orlower the
rear portion of the driver’s seat cushion.
RECLINING
 Push the reclining switch
forward to
move the seatback forward; pull it back to move the seatback backward.
LUMBAR SUPPORT (driver’s seat, if so equipped)
 Push the adjusting lever/switch
repeatedly to adjust the lumbar support.
PASSENGER REAR SEAT ENTRY (Coupe only)
FROM INSIDE THE VEHICLE
From the driver’s seat:
 Pull theupper seatback releaselever
,located onthe
inboard sideofthe passenger frontseat, tothe uppermost
position and slide the seat forward.
From the back seat:
 Step orpush down onthe lower seatback releaselever
located onthe backside lowerportion ofthe passenger seatandpush theseatback,
sliding it forward.
FROM OUTSIDE THE VEHICLE
From the driver’s side:
 Pull theupper seatback releaselever
,located onthe
outboard sideofthe driver’s frontseat. (Return theseatback
manually by pushing the seatback rearward.)
From the passenger side:
 Pull the seatback release lever
fully up until the seatback
releases, and push the seatback, sliding it forward. (Return the seatback manually by
pushing the seatback rearward.)
Coupe
Sedan
15

FOLDING DOWN THE REAR SEATS
FROM INSIDE THE VEHICLE The rear seats canbelocked usingthemechanical keyto
prevent unauthorized access.
 Open the access cover and press the release button
to
fold down the center/passenger’s side rear seat.
 Reach through the opening and pull on the strap
located
behind the seat to fold down the driver’s side rear seat.
FROM THE TRUNK
 Pull thestrap
located behindtheseat tofold down the
center/passenger’s side rear seat.
 Pull on the strap
located behind the seat to fold down the
driver’s side rear seat.
HOMELINK UNIVERSAL TRANSCEIVER (if so equipped)
SYSTEM OPERATING TIPS
 Garage doors, electrical gates, entry doors, etc. will be activated during programming.
To avoid injury, make sure that people and objects are clear of all doors or gates during
programming. Yourvehicle’s engineshouldbeturned offwhile programming the
HomeLink Transceiver.
 To program your HomeLink Transceiver to operate a garage door, gate, or entry door
opener, home or office lighting, you need to be at the same location as the device.
NOTE: Garage dooropeners (manufactured after1996) have“rolling codepro-
tection”. Toprogram agarage dooropener equipped with“rolling codeprotec-
tion”, you will need to use a ladder to get up to the garage door opener motor to
be able to access the “smart” or “learn” program button.
PROGRAMMING YOUR HOMELINK UNIVERSAL TRANSCEIVER (Mirror,
Sun Visor or Overhead Console)
1. To begin, pressandhold thetwo
outer HomeLink buttons(toclear
the memory) until the indicator light
blinks slowly (after20seconds) .
Release both buttons.
2. Position theend ofthe hand-held
transmitter 1-3 in (26-76 mm) away
from the HomeLink surface.
16