2009 HUMMER H3 ECU

Safety Chains
Always attach chains between the
vehicle and the trailer. Cross
the safety chains under the tongue
of the trailer to help prevent the
tongue from contacting the road if it
becomes separated from the
hitch. Always leave just enough
slack so the rig can turn. Never
allow safety chains to drag on the
ground.
Trailer Brakes
A loaded trailer that weighs more
than 1,500 lbs (680 kg) needs
to have its own brake system that is
adequate for the weight of the
trailer. Be sure to read and follow
the instructions for the trailer brakes
so they are installed, adjusted
and maintained properly.
Driving with a Trailer
Towing a trailer requires a certain
amount of experience. Get to
know the rig before setting out for
the open road. Get acquainted
with the feel of handling and braking
with the added weight of the
trailer. And always keep in mind that
the vehicle you are driving is now
longer and not as responsive as the
vehicle is by itself.
Before starting, check all trailer hitch
parts and attachments, safety
chains, electrical connectors, lamps,
tires and mirror adjustments. If
the trailer has electric brakes, start
the vehicle and trailer moving
and then apply the trailer brake
controller by hand to be sure
the brakes are working. This checks
the electrical connection at the
same time.
During the trip, check occasionally
to be sure that the load is secure,
and that the lamps and any
trailer brakes are still working.
Following Distance
Stay at least twice as far behind
the vehicle ahead as you would
when driving the vehicle without a
trailer. This can help to avoid
situations that require heavy braking
and sudden turns.
Passing
More passing distance is needed
when towing a trailer. Because
the rig is longer, it is necessary to
go much farther beyond the
passed vehicle before returning to
the lane.
Backing Up
Hold the bottom of the steering
wheel with one hand. Then, to move
the trailer to the left, move that
hand to the left. To move the trailer
to the right, move your hand to
the right. Always back up slowly
and, if possible, have someone
guide you.
4-48 Driving Your Vehicle

3. Fill the radiator with the proper
DEX-COOL coolant mixture, up
to the base of the ller neck.
SeeEngine Coolant on
page 5-23for more information
about the proper coolant mixture.
4. Fill the coolant recovery tank to
the FULL COLD mark.5. Reinstall the cap on the coolant
recovery tank, but leave the
radiator pressure cap off.
6. Start the engine and let it run
until you can feel the upper
radiator hose getting hot. Watch
out for the engine cooling fan.7. By this time, the coolant level
inside the radiator ller neck
might be lower. If the level
is lower, add more of the proper
DEX-COOL coolant mixture
through the ller neck until the
level reaches the base of the
ller neck.
8. Then replace the pressure cap.
At any time during this procedure
if coolant begins to ow out of
the ller neck, reinstall the
pressure cap.
Notice:If the pressure cap is not
tightly installed, coolant loss
and possible engine damage
may occur. Be sure the cap is
properly and tightly secured.
5-26 Service and Appearance Care

Windshield Wiper
Blade Replacement
Windshield wiper blades should be
inspected for wear and cracking.
SeeScheduled Maintenance
on page 6-4for more information.
Replacement blades come in
different types and are removed in
different ways. For proper type
and length, seeMaintenance
Replacement Parts on page 6-14.
To replace the windshield wiper
blade:
1. Lift the wiper arm away from the
windshield.2. Push the release lever (B) to
disengage the hook and push
the wiper arm (A) out of the
blade (C).
3. Push the new wiper blade
securely on the wiper arm
until you hear the release lever
click into place.
To replace the rear wiper blade,
lift the rear wiper arm from the
window and pull the blade.
Tires
Your new vehicle comes with
high-quality tires made by
a leading tire manufacturer.
If you ever have questions about
your tire warranty and where
to obtain service, see your
vehicle Warranty booklet
for details. For additional
information refer to the tire
manufacturer.
{CAUTION
Poorly maintained and
improperly used tires are
dangerous.
Overloading your
vehicle’s tires can
cause overheating as a
result of too much exing.
You could have an air-out
and a serious accident.
SeeLoading the Vehicle
on page 4-35.
(Continued)
5-44 Service and Appearance Care

8. Proceed to the driver side rear
tire, and repeat the procedure
in Step 5.
9. After hearing the conrming horn
chirp for the driver side rear tire,
check to see if the TPMS low tire
warning light and the DIC LOW
TIRE messages have turned off.
If yes, the TPMS sensors have
been relearned. Turn the ignition
switch to LOCK/OFF.
If the low tire warning light and
the SERV TPM message on the
DIC are on after completing
Step 5 for the driver side rear tire,
the sensor relearn process has
not been successful. Turn the
ignition switch to LOCK/OFF and
repeat the matching process
beginning with Step 2.
10. Set all four tires to the
recommended air pressure level
as indicated on the Tire and
Loading Information label.
11. Put the valve caps back on the
valve stems.Tire Inspection and
Rotation
We recommend that you
regularly inspect the vehicle’s
tires, including the spare tire,
for signs of wear or damage.
SeeWhen It Is Time for
New Tires on page 5-58for
more information.
Tires should be rotated
every 5,000 to 8,000 miles
(8 000 to 13 000 km).
SeeScheduled Maintenance
on page 6-4.
The purpose of a regular tire
rotation is to achieve a uniform
wear for all tires on the vehicle.
This will ensure that the
vehicle continues to perform
most like it did when the
tires were new.Any time you notice unusual
wear, rotate the tires as soon
as possible and check wheel
alignment. Also check for
damaged tires or wheels.
SeeWhen It Is Time for
New Tires on page 5-58and
Wheel Replacement on
page 5-64.
Make sure the spare tire is
stored securely. Push, pull and
then try to rotate or turn the
tire. If it moves, use the wheel
wrench/hoist shaft to tighten
the cable. SeeChanging a
Flat Tire on page 5-66.
Service and Appearance Care 5-57

Tire Chains
{CAUTION
If your vehicle has LT285/75R16
or P265/65R18 size tires, do not
use tire chains. They can damage
your vehicle because there is not
enough clearance. Tire chains
used on a vehicle without the
proper amount of clearance can
cause damage to the brakes,
suspension, or other vehicle parts.
The area damaged by the tire
chains could cause you to lose
control of your vehicle and you or
others may be injured in a crash.
(Continued)
CAUTION (Continued)
Use another type of traction
device only if its manufacturer
recommends it for use on your
vehicle and tire size combination
and road conditions. Follow that
manufacturer’s instructions.
To help avoid damage to your
vehicle, drive slowly, readjust,
or remove the device if it is
contacting your vehicle, and do
not spin your vehicle’s wheels.
If you do nd traction devices
that will t, install them on the
rear tires.Notice:If your vehicle has a
tire size other than LT285/75R16
or P265/65R18 use tire chains
only where legal and only when
you must. Use chains that are
the proper size for your tires.
Install them on the tires of
the rear axle. Do not use chains
on the tires of the front axle.
Tighten them as tightly as
possible with the ends securely
fastened. Drive slowly and
follow the chain manufacturer’s
instructions. If you can hear
the chains contacting your
vehicle, stop and retighten them.
If the contact continues, slow
down until it stops. Driving
too fast or spinning the wheels
with chains on will damage
your vehicle.
Service and Appearance Care 5-65

Removing the Spare Tire
and Tools (H3)
The equipment needed is located in
the swing-gate, behind a cover.
To remove the equipment:
1. Open the swing-gate.
SeeSwing-gate on page 2-9.
2. Remove the cover, located on
the inside of the swing-gate,
by lifting the two latches.
3. Turn the wing nut
counterclockwise to release
the jack tool bag and jack
and remove them.4. Undo the straps that secure the
jack tool bag to the jack.
5. Open the tool bag to nd the
following tools, which are
used to remove the spare tire
and at tire:
A. Wheel Wrench
B. Jack Handle Extensions
C. Jack Handle
D. Jack
E. Wheel BlocksThe spare tire is attached to the
outside of the swing-gate.
To remove the spare tire:
1. If the vehicle has a spare tire
cover release the latch by
pulling the latch straight back
and turning it away from
the cover at the same time.
Notice:Opening the endgate
before completely closing and
latching the spare tire cover may
result in damage to your vehicle.
Close and latch the spare tire
cover before opening the endgate
to avoid possible damage.
5-68 Service and Appearance Care

Remove the center cap, if
equipped, by placing the at
end of the wheel wrench in the
slot on the wheel and gently
pry the center cap out.2. Use the wheel wrench to remove
the wheel nuts securing the
spare tire.
If the vehicle has locking lug
nuts, the key is supplied in the
tool bag. Use the key along
with the wheel wrench to remove
the wheel nuts from the tire.
3. You may need assistance to
remove the spare tire. Pull
off and gently lower the spare
tire to the ground. Set it next to
the at tire.
Removing the Spare Tire
and Tools (H3T)
To access the jack and tools
located under the rear seat:
1. Turn the wing nut (A)
counterclockwise to release
the jack and tools.
2. Remove the jack and tool kit
from the bracket.
3. Release the straps (B) that
secure the tool bag to the jack.
Service and Appearance Care 5-69

4. Use the wheel wrench to tighten
the nuts rmly. Try to move the
tire back and forth slightly to
be sure it is secure.
5. Reinstall the center tire cover
onto the spare or at tire.
6. If the vehicle has a spare tire
cover close the cover and
latch the side latch.To store the jack tool bag and jack:
1. Return the tools to the jack
tool bag.
2. Secure the tool bag to the jack
by securely wrapping the straps
around the jack. Then, slide
the straps through the rings on
the bag and secure.
3. Position the jack and jack tool
bag in the swing-gate.
When reinstalling the jack and
jack tool bag, make sure the jack
base is securely seated behind
the tabs in the swing-gate.4. Reinstall the wing nut retainer to
fasten the jack and tool bag in
the storage compartment.
Make sure that the wing nut
passes through the tool bag and
the jack before tightening it.
5. Turn the wing nut retainer
clockwise to secure.
6. Reinstall the compartment cover
by inserting the locator tabs in
the holes in the swing-gate.
Push the latches down to secure.
Service and Appearance Care 5-79