2009 HUMMER H3 service indicator

This device complies with RSS-210
of Industry Canada. Operation is
subject to the following two
conditions:
1. This device may not cause
interference.
2. This device must accept any
interference received, including
interference that may cause
undesired operation of the
device.
The Canadian Registration
ID number is 2791021849A.
Changes or modications to this
system by other than an authorized
service facility could void
authorization to use this equipment.Universal Home Remote
System Operation
If there is one triangular Light
Emitting Diode (LED) indicator
light above the Universal Home
Remote buttons, follow the
instructions below.
This system provides a way to
replace up to three remote control
transmitters used to activate devices
such as garage door openers,
security systems, and home
automation devices.Do not use the Universal Home
Remote with any garage door
opener that does not have the stop
and reverse feature. This includes
any garage door opener model
manufactured before April 1, 1982.
Read the instructions completely
before attempting to program
the Universal Home Remote.
Because of the steps involved,
it may be helpful to have another
person available to assist you in
the programming the Universal
Home Remote.
Keep the original hand-held
transmitter for use in other vehicles
as well as for future Universal
Home Remote programming.
It is also recommended that
upon the sale of the vehicle, the
programmed Universal Home
Remote buttons should be erased
for security purposes. See “Erasing
Universal Home Remote Buttons”
later in this section.
Features and Controls 2-43

If the airbag readiness light stays on
after the vehicle is started or
comes on while driving, the airbag
system may not work properly. Have
the vehicle serviced right away.
{CAUTION
If the airbag readiness light stays
on after the vehicle is started or
comes on while driving, it means
the airbag system might not be
working properly. The airbags in
the vehicle might not inate in a
crash, or they could even inate
without a crash. To help avoid
injury, have the vehicle serviced
right away.
The airbag readiness light should
ash for a few seconds when
the engine is started. If the light
does not come on then, have it xed
immediately. If there is a problem
with the airbag system, an
airbag Driver Information Center(DIC) message may also come on.
SeeDIC Warnings and Messages
on page 3-37for more information.
Passenger Airbag
Status Indicator
The vehicle has the passenger
sensing system. SeePassenger
Sensing System on page 1-54
for important safety information. The
instrument panel has a passenger
airbag status indicator.When the vehicle is started, the
passenger airbag status indicator
will light ON and OFF, or the symbol
for on and off, for several seconds
as a system check. Then, after
several more seconds, the status
indicator will light either ON or OFF,
or either the on or off symbol to
let you know the status of the right
front passenger frontal airbag
and seat-mounted side impact
airbag (if equipped).
If the word ON or the on symbol is
lit on the passenger airbag status
indicator, it means that the right front
passenger frontal airbag and
seat-mounted side impact airbag (if
equipped) are enabled (may
inate).
If the word OFF or the off symbol is
lit on the airbag status indicator,
it means that the passenger sensing
system has turned off the right
front passenger frontal airbag and
seat-mounted side impact airbag (if
equipped). United States
Canada
3-26 Instrument Panel

If, after several seconds, both status
indicator lights remain on, or if
there are no lights at all, there may
be a problem with the lights or
the passenger sensing system. See
your dealer/retailer for service.
{CAUTION
If the airbag readiness light ever
comes on and stays on, it means
that something may be wrong with
the airbag system. To help avoid
injury to yourself or others, have
the vehicle serviced right away.
SeeAirbag Readiness Light on
page 3-25for more information,
including important safety
information.
Charging System Light
This light comes on briey when the
ignition key is turned, but the
engine is not running, as a check to
show it is working.
It should go out once the engine
starts. If it stays on, or comes
on while driving, there could be a
problem with the charging system. A
charging system message in the
Driver Information Center (DIC) may
also appear. SeeDIC Warnings
and Messages on page 3-37
for more information. This light could
indicate that there are problems
with a generator drive belt, or that
there is an electrical problem.
Have it checked right away. If the
vehicle must be driven a short
distance with the light on, turn off all
the accessories, such as the
radio and air conditioner.
Up-Shift Light
The vehicle may have an up-shift
light.
When this light comes on, shift to
the next higher gear if weather,
road, and traffic conditions allow.
SeeManual Transmission Operation
on page 2-22for more information.
Brake System Warning
Light
The vehicle’s hydraulic brake
system is divided into two parts. If
one part is not working, the
other part can still work and stop
the vehicle. For good braking
though, both parts need to be
working well.
Instrument Panel 3-27

If the warning light comes on, there
could be a brake problem. Have
the brake system inspected
right away.
This light comes on briey when the
ignition key is turned to ON/RUN.
If it does not, have it xed so it
will be ready to warn if there is a
problem.
When the ignition is on, the brake
system warning light comes on
when the parking brake is set. See
Parking Brake on page 2-28for
more information. The light stays on
if the parking brake does not
release fully. If it stays on after the
parking brake is fully released, it
means there is a brake problem.If the light comes on while driving,
pull off the road and stop. The brake
pedal might be harder to push, or
it might go closer to the oor. It can
take longer to stop. If the light is
still on, have the vehicle towed for
service. SeeTowing Your Vehicle
on page 4-40.
{CAUTION
The brake system might not be
working properly if the brake
system warning light is on. Driving
with the brake system warning
light on can lead to a crash. If the
light is still on after the vehicle
has been pulled off the road and
carefully stopped, have the
vehicle towed for service.
Antilock Brake System
(ABS) Warning Light
For vehicles with the Antilock Brake
System (ABS), this light comes
on briey when the engine is started.
If it does not, have the vehicle
serviced by your dealer/retailer. If
the system is working normally
the indicator light will then go off.
If the ABS light stays on, turn
the ignition off. If the light comes on
while driving, stop as soon as it
is safely possible and turn the
ignition off. Then start the engine
again to reset the system. If the ABS
light stays on, or comes on again
while driving, the vehicle needs
service. If the regular brake system
warning light is not on, the vehicle
still has brakes, but not antilock
brakes. If the regular brake system
warning light is also on, the
vehicle does not have antilock United States
Canada
3-28 Instrument Panel

brakes and there is a problem with
the regular brakes. SeeBrake
System Warning Light on page 3-27.
For vehicles with a Driver
Information Center (DIC), seeDIC
Warnings and Messages on
page 3-37for all brake related DIC
messages.
StabiliTrak®/Traction
Control System (TCS)
Warning Light
The StabiliTrak system or the
Traction Control System (TCS)
indicator/warning light comes
on briey while starting the engine.
If it does not, have the vehicle
serviced by your dealer/retailer. If
the system is working normally
the indicator light will then go off.The indicator/warning light ashes
while the StabiliTrak or TCS system
is working to control the vehicle
on a low traction surface.
If the TCS warning light comes on
and stays on while driving, the
vehicle needs service.
The light comes on when the TCS
and the StabiliTrak system is
turned off. If the TCS is off, wheel
spin is not limited. If the StabiliTrak
system is off, the system does
not assist in controlling the vehicle.
Turn on the TCS and the
StabiliTrak system and the warning
light turns off.
SeeStabiliTrak
®System on
page 4-6andTraction Control
System (TCS) on page 4-7for more
information
Engine Coolant
Temperature Gage
This gage shows the engine coolant
temperature.
If the gage pointer is in the shaded
area of the gage, the engine is
too hot. It means that the engine
coolant has overheated. If the
vehicle has been operating under
normal driving conditions, pull off the
road, stop your vehicle and turn
off the engine as soon as possible.
SeeEngine Overheating on
page 5-27for more information.
United StatesCanada
Instrument Panel 3-29

Tire Pressure Light
The tire pressure light should come
on briey as the engine is started.
If it does not, have the vehicle
service by your dealer/retailer. It
provides information about tire
pressures and the Tire Pressure
Monitoring System.
When the Light is On Steady
This indicates that one or more of
the tires are signicantly
underinated.
A tire pressure message in the
Driver Information Center (DIC),
may accompany the light. SeeDIC
Warnings and Messages on
page 3-37for more information.
Stop and check the tires as soon as
it is safe to do so. If underinated,
inate to the proper pressure.
SeeTires on page 5-44for more
information.When the Light Flashes First and
Then is On Steady
This indicates that there may be a
problem with the Tire Pressure
Monitor System. The light ashes
for about a minute and stays
on steady for the remainder of the
ignition cycle. This sequence
will repeat with every ignition cycle.
SeeTire Pressure Monitor System
on page 5-52for more information.
Malfunction
Indicator Lamp
Check Engine Light
A computer system called OBD II
(On-Board Diagnostics-Second
Generation) monitors operation of
the fuel, ignition, and emission
control systems. It ensures
that emissions are at acceptable
levels for the life of the vehicle,
helping to produce a cleaner
environment.This light comes on when the
ignition is on, but the engine is not
running, as a check to show it
is working. If it does not, have the
vehicle serviced by your
dealer/retailer.
If the check engine light comes on
and stays on, while the engine
is running, this indicates that there
is an OBD II problem and service
is required.
Malfunctions often are indicated by
the system before any problem
is apparent. Being aware of the light
can prevent more serious damage
to the vehicle. This system
assists the service technician in
correctly diagnosing any
malfunction.
Notice:If the vehicle is
continually driven with this light
on, after a while, the emission
controls might not work as well,
3-30 Instrument Panel

CHANGE OIL
This message displays when the oil
needs to be changed. Check the
oil in the vehicle as soon as possible
and have the vehicle serviced by
your dealer/retailer. SeeEngine Oil
on page 5-13andScheduled
Maintenance on page 6-4for more
information. Press and release
the reset stem to acknowledge the
message and clear it from the
display.
DOORS
This message displays when one or
more of the doors is ajar. Check
all the doors on the vehicle to make
sure they are closed. The message
clears from the display after all
of the doors are closed.
ENG (Engine) HOT
This message displays when the
engine coolant temperature is
hot. Check the engine coolant
temperature gage. SeeEngine
Coolant Temperature Gage
on page 3-29. Have the vehicleserviced by your dealer/retailer as
soon as possible if you suspect
the engine is overheating. See
Engine Overheating on page 5-27
for more information.
FLUID
This message displays if the brake
uid is low. Check the brake
uid as soon as possible and have
the vehicle serviced by your
dealer/retailer. SeeBrakes on
page 5-30for more information.
Press and release the reset stem to
acknowledge the message and
clear it from the display.
FUEL CAP
This message displays if the
vehicle’s fuel cap is either off or
loose. Pull over as soon as possible
and check to see if the fuel cap is
secure. You may also see the check
engine light on the instrument
panel cluster. If the check engine
light does come on when the
fuel cap was loose, it may take a
few driving trips before the lightturns off. SeeMalfunction Indicator
Lamp on page 3-30for more
information if the light still remains
on. Press and release the reset
stem to acknowledge the message
and clear it from the display.
HSA (Hill Start Assist) ON
This message displays when the Hill
Start Assist is enabled. See
Braking on page 4-3for more
information.
LOW FUEL
This message displays if the level of
fuel in the vehicle is low. Also
check the fuel gage. SeeFuel Gage
on page 3-33for more information.
Rell the fuel tank as soon as
possible.
LOW TIRE
On vehicles with the Tire Pressure
Monitor System (TPMS), this
message displays if a low tire
pressure is detected in any of the
vehicle’s tires. Press and release the
reset stem to acknowledge the
3-38 Instrument Panel

The malfunction indicator lamp
could turn on and the vehicle
might fail a smog-check test.
SeeMalfunction Indicator Lamp
on page 3-30. If this occurs, return
to your authorized dealer/retailer
for diagnosis. If it is determined
that the condition is caused by the
type of fuel used, repairs might
not be covered by the vehicle
warranty.
Additives
To provide cleaner air, all gasolines
in the United States are now
required to contain additives that
help prevent engine and fuel system
deposits from forming, allowing
the emission control system to work
properly. In most cases, you
should not have to add anything to
the fuel. However, some gasolines
contain only the minimum amount of
additive required to meet U.S.
Environmental Protection Agency
regulations. To help keep fuel
injectors and intake valves clean, orif the vehicle experiences problems
due to dirty injectors or valves,
look for gasoline that is advertised
as TOP TIER Detergent Gasoline.
For customers who do not use
TOP TIER Detergent Gasoline
regularly, one bottle of GM Fuel
System Treatment PLUS, added to
the fuel tank at every engine oil
change, can help clean deposits
from fuel injectors and intake valves.
GM Fuel System Treatment PLUS
is the only gasoline additive
recommended by General Motors.
Also, your dealer/retailer has
additives that will help correct and
prevent most deposit-related
problems.
Gasolines containing oxygenates,
such as ethers and ethanol,
and reformulated gasolines
might be available in your area.
We recommend that you use these
gasolines, if they comply with
the specications described earlier.However, E85 (85% ethanol) and
other fuels containing more than
10% ethanol must not be used
in vehicles that were not designed
for those fuels.
Notice:This vehicle was not
designed for fuel that contains
methanol. Do not use fuel
containing methanol. It can
corrode metal parts in the fuel
system and also damage plastic
and rubber parts. That damage
would not be covered under
the vehicle warranty.
Some gasolines that are
not reformulated for low
emissions can contain an
octane-enhancing additive called
methylcyclopentadienyl manganese
tricarbonyl (MMT); ask the
attendant where you buy gasoline
whether the fuel contains MMT.
We recommend against the use of
such gasolines. Fuels containing
MMT can reduce the life of
spark plugs and the performance
5-6 Service and Appearance Care