2009 HONDA ODYSSEY stop

To load a single disc:Press and release the LOAD
button.
TheindicatorsabovetheDisc
buttons of the empty positions will
blink, and the green CD load
indicator comes on. When you see
‘‘LOAD’’ in the display, insert the
disc into the CD slot. Insert it only
about half way; the drive will pull it
in the rest of the way.
The system will load the disc and
begin playing it. If you press the LOAD button while
a disc is playing, the system will stop
playing that disc and start the
loading sequence. It will then play
the disc just loaded.
You can also load a disc into an
empty position while a disc is playing
by pressing the appropriate disc
button. Select an empty disc button
(the indicator above the button is
of f ), and press the button. The
system will stop playing the current
disc and start the loading sequence.
It will then play the disc just loaded.
You cannot load and play 3-inch
(8-cm)discsinthissystem. Each time you press the DISP button,
the display shows you the text data
on a disc, if the disc was recorded
with text data.
You can see the album, artist, and
track name in the display. If a disc is
recorded in MP3 or WMA, you can
see the f older and f ile name, and the
album, artist, and track tag.
With the f older name, you will see
the FOLDER indicator in the display.
The TRACK indicator is shown with
the file or track name.
When you press and release the
DISP button while a disc without text
data is playing, you will see ‘‘NO
INFO’’ on the display.
The display shows up to 16
characters of selected text data (the
f older name, f ile name, etc.).
2.
1.
3.
Playing Discs (Models with navigation system)
T ext Data Display Function
266
\f—\f—
y

\f\fy
(\fy\f
y
2009 Odyssey

Î
µ
ÛÎ
Dolby noise reduction turns on
when you insert a tape. The indicator will come on in the
display. If the tape was not recorded
in Dolby, turn it of f by pressing the
NR button. Dolby remains of f until
you press the NR button again.
To remove the tape, press the
EJECT button. If you want to turn
the player of f , press the PWR/VOL
knob or turn of f the ignition. The
tape will remain in the drive. When
youturnthesystembackon,the
tape will begin playing where it lef t
off. To switch to the radio or CD player
while a tape is playing, press the AM
or FM button or AM/FM button, or
CD button. To change back to the
tape player, press the AUX button.
To rewind the tape,
push the REW button. You will see
REW in the display. To f ast f orward
the tape, push the FF button. You
will see FF displayed. Press the FF,
REW, or PLAY/PROG button to
take the system out of rewind or fast
forward.
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position. Make sure the open side of
thetapeisfacingright,theninsert
thetapemostof thewayintotheslot.
Thesystemwillpullthetapeinthe
rest of the way and begin to play it.
The tape direction indicator will
come on to show you which side of
the tape is playing. The indicates
the side you inserted upward is now
playing. If you want to play the other
side, press the PLAY/PROG button.
When the player reaches the end of
the tape, it will automatically reverse
direction and play the other side.
Dolby noise reduction is manufactured under
license from Dolby Laboratories Licensing
Corporation. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
CONT INUED
Optional on some models
To Play a Tape
To Stop Playing a TapeT ape Search Functions
FF/REW
Playing a T ape (Optional)
Features
279
\f—\f—
y


y
(\fy\fy
2009 Odyssey

ÝÛ
When you press the SETUP button
on the rear control panel when a
DVD is not playing, the ‘‘INITIAL
SETTINGS’’ menu is displayed. When you select ‘‘Language’’ with
the or button, the menu
shown above appears.
To return to the stop or prestop
screen, select ‘‘Close’’ using the
or button, and then press
the ENT, or the SETUP button. To select the language used in the
DISC menus, select ‘‘Menu Lang’’ by
pressing the or button. You will
see the submenu next to ‘‘Menu
Lang.’’
There are two selectable menus:
‘‘Language’’ and ‘‘Others.’’ Menu Language
CONT INUED
INITIAL SETTINGS Menu
INITIAL SETTINGS (Language)
Rear Entertainment System
Features
303
\f—\f—
y

y
(\fy\f\fy
2009 Odyssey

·µ
The HomeLink
Universal
Transceiver built into your vehicle
canbeprogrammedtooperateupto
three remote controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
Bef ore programming your
HomeLink to operate a garage door
opener, conf irm that the opener has
an external entrapment protection
system, such as an ‘‘electronic eye,’’
or other saf ety and reverse stop
f eatures.
If your garage door was
manuf actured bef ore April 1, 1982,
you may not be able to program
HomeLink to operate it. These units
do not have safety features that
cause the motor to stop and reverse
it if an obstacle is detected during
closing, increasing the risk of injury. Do not use HomeLink with any
garage door opener that lacks saf ety
stop and reverse f eatures.
Units manuf actured between April 1,
1982 and January 1, 1993 may be
equipped with saf ety stop and
reverse f eatures. If your unit does
not have an external entrapment
protection system, an easy test to
conf irm the f unction and
perf ormance of the saf ety stop and
reverse f eature is to lay a 2 4
under the closing door. The door
should stop and reverse upon
contacting the piece of wood.
As an additional safety feature,
garage door openers manuf actured
af ter January 1, 1993 are required to
have external entrapment protection
systems, such as an electronic eye,
which detect an object obstructing
the door.
Refer to the safety information thatcame with your garage door opener
to test that the safety features are
f unctioning properly. If you do not
have this information, contact the
manuf acturer of the equipment.
Bef ore programming HomeLink to a
garage door or gate opener, make
sure that people and objects are out
of thewayof thedevicetoprevent
potential injury or damage.
When programming a garage door
opener, park just outside the garage.
If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the first button. To do this,
press and hold the two outside
buttons on the HomeLink
transceiver for about 20 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1.
On EX, EX-L and Touring models
HomeL inkUniversal Transceiver
General Inf ormation
Important Saf ety PrecautionsT raining HomeL ink
Bef ore you begin
322
\f—\f—
y


\fy
(\fy\fy
2009 Odyssey

To go back one step in a command
process, say ‘‘Go back,’’ or press
the HFL Back button.
If nothing is said while HFL is
listening f or a command, HFL will
time out and stop its voice
recognition, then prompt you with
available options or help
inf ormation. The next time you
press the HFL Talk button, HFL
begins listening f rom the point at
which it timed out.
To end a command sequence at
any time, press and hold the HFL
Back button, or press and release
the HFL Talk button, wait for the
beep, and say ‘‘Cancel.’’ The next
time you press the HFL Talk
button, HFL begins f rom the main
menu.When you f inish a command
sequence, HFL returns to idle. For
example, when you store the name
‘‘Eric,’’ the HFL system response
is ‘‘Eric has been stored.’’ The
next time you press the HFL Talk
button, HFL begins f rom the main
menu.
Your Bluetooth
compatible phone
with Hands Free Prof ile must be
paired to HFL bef ore you can make
and receive hands-free calls. To
conf irm that your phone is
Bluetooth
compatible, visit , or call (888)
528-7876. In Canada, call (888) 9-
HONDA-9. Your phone retailer
should also be able to conf irm that
your phone is Bluetooth
compatible. HFL does not allow you to pair
your phone if the vehicle is
moving.
For pairing, your phone must be in
its discovery mode (searching f or
a Bluetooth related device).
Up to six phones can be paired to
HFL.
Your phone’s battery may drain
f aster when it is paired to HFL.
The f ollowing procedure works f or
most phones. If you cannot pair
your phone to HFL with this
procedure, ref er to your phone’s
operating manual, visit
,callthe
HandsFreeLink
consumer
support at (888) 528-7876, or call
your phone retailer. In Canada,
call (888) 9-HONDA-9.
handsf reelink.honda.com
handsf reelink.honda.com
BluetoothHandsFreeL ink
Pairing Your PhoneNOT E:
330
\f—\f—
y


y
(\fy\fy
2009 Odyssey

»¼
ÎÎ
CONT INUED
Press and release the Talk button.
Af ter the beep, if you say ‘‘Yes.’’
HFL responds ‘‘Entering phone
set up: pair menu. The pairing
process requires operation of your
Bluetooth phone. For saf ety, only
perf orm this f unction while the
vehicle is stopped.’’
HFL responds ‘‘For proper system
f unction a compatible Bluetooth
phone is required. Please visit the
HandsFreeLink
website, listed in
the owner’s manual, f or a list of
approved phones and other system
inf ormation. HandsFreeLink is
waiting to pair with a Bluetooth
phone. From your phone, search
f or Bluetooth devices and select
HandsFreeLink.’’
During the pairing process, turn
of f any previously paired phones
bef ore pairing a new phone.
Each time a phone is paired with
HFL, the system selects a pairing
code randomly or sequentially.
You can switch this setting
between random mode and f ixed
mode. To select a pairing code
setting between Random and
Fixed, refer to page .
If af ter three minutes your phone
is not ready to pair or a phone is
not f ound, the system will time out
andreturntoidle.
Park your vehicle. With your
phone on and the ignition switch in
the ACCESSORY (I) or ON (II)
position, press and release the
Talk button.
HFL prompts ‘‘Welcome to
Bluetooth HandsFreeLink. This
system enables hands-f ree usage
of a mobile phone. Bef ore using
this system, a phone needs to be
paired or connected with
HandsFreeLink. Would you like to
pair a phone now? Press the
Bluetooth HandsFreeLink Talk
button, and after the beep, say Yes,
to begin the pairing process, or No,
to continue.’’
HFL responds ‘‘When prompted
by your mobile phone, enter the
pairing code: 1234 .’’
Go to Step 4.
1.
2.
For example
:
336
To pair your f irst phone, f ollow the
prompts on the HFL system:
BluetoothHandsFreeL ink
Features
331
\f—\f—y
y
(\fy\fy
2009 Odyssey

To activate this function, do this:To mute your voice, do this:To unmute your voice, do this:
During a call, you can mute or
unmute your voice to the person you
are talking to.
Press and release the Talk button.
Af ter the beep, say ‘‘Mute.’’
HFL responds ‘‘Mute is active.’’
Press and release the Talk button.
Af ter the beep, say ‘‘Mute.’’
HFL responds ‘‘Mute is canceled.’’
Press and release the Talk button.
Af ter the beep, say ‘‘System setup.’’
HFL responds ‘‘System setup
options are security, change
passcode, call notif ication, auto
transf er, and clear. Press the Talk
button and say a command.’’
If this feature is set to on, HFL
responds ‘‘Auto-transf er is enabled.
Calls dialed on the phone will be
automatically transferred to
Bluetooth HandsFreeLink. Would
you like to disable Auto Transf er? Press the Talk button and say Yes
or No.’’
If this feature is set to off, HFL
responds ‘‘Auto transf er is
disabled. Calls dialed on the phone
do not automatically transf er to
Bluetooth HandsFreeLink. Would
you like to enable Auto Transf er?
Press the Talk button and say Yes
or No.’’
Press and release the Talk button.
Af ter the beep, say ‘‘Auto transf er.’’ If the setting changes from off to
on, press and release the Talk
button. Af ter the beep, say ‘‘Yes.’’
HFL responds ‘‘Auto transf er is
enabled.’’
When you make a call directly f rom
the phone with the auto transf er on,
make sure to stop your vehicle saf ely.
To end the call, press the Back
button. Never try to dial from your
phonedirectlyif thevehicleis
moving.
If the setting changes from on to off,
HFL responds ‘‘Auto transf er is
disabled. Use the Transf er command
at the HandsFree main menu to
manually transf er calls dialed on the
phone.’’
1.
2.
3.
BluetoothHandsFreeL ink
Muting a Call
Features
345
NOTE:
\f—\f—
y
\f\fy
(\fy\f\fy
2009 Odyssey

»¼
»¼
CONT INUED
You can store the desired number to
the HFL phonebook directly f rom
your cell phone. Your phone may not have
phonebook import f unction. Visit ,orcallthe
HandsFreeLink
consumer support
at (888) 528-7876. In Canada, call
(888) 9-HONDA-9. You can see your
phone’s owner’s manual f or
inf ormation. Press and release the Talk button.
After the beep, say the name you
would like to store. For example,
say ‘‘Neil at work.’’
With your phone on and the
ignition switch in the
ACCESSORY (I) or ON (II)
position, press and release the
Talk button. After the beep, say
‘‘Phonebook.’’
HFL responds ‘‘Phonebook
options are store, edit, delete,
receive contact, and list. Press the
Talk button and say a command.’’ Press and release the Talk button.
Af ter the beep, say ‘‘Receive
contact.’’
HFL responds ‘‘The receive
process requires operation of your
Bluetooth device. For saf ety, only
perf orm this f unction while the
vehicle is stopped. HandsFreeLink
is now waiting to receive a contact
f rom a Bluetooth device.’’
Select a desired number f rom the
list on your phone, and send it via
Bluetooth (steps will vary f or
phone types, f ollow your phone’s
operating manual).
HFL responds, f or example ‘‘ 2
phone numbers have been
received f or this contact. What
name would you like to store f or
the mobile number
1234567891 ? Press the Talk
button and say a name or say
Discard, to discard this number.’’ HFL responds ‘‘Neil at work will
be stored. Is this correct? Press
the Talk button and say Yes or No.’’
Go to step 6.
If you say, ‘‘No,’’ HFL returns to
idle.
HFL responds ‘‘Neil at work has
been stored. Would you like
HandsFreeLink to receive another
contact? Press the Talk button and
say Yes or No.’’
Press and release the Talk button.
Af ter the beep, if you say ‘‘Yes.’’
2.
4.
1. 3.
5.
handsf reelink.honda.com
BluetoothHandsFreeL ink
Storing a Phone Number Directly
f rom Your Phone
Features
349
NOTE:
\f—\f—
y
\f
y
(\fy\fy
2009 Odyssey