2009 FIAT ULYSSE Owners Manual

TECHNICAL SPECIFICATIONS
224
Maximum speed index
Q =up to 160 km/h
R =up to 170 km/h
S =up to 180 km/h
T =up to 190 km/h
U =up to 200 km/h
H =up to 210 km/h
V =over 210 km/h
ZR =over 240 km/h
W =up to 270 km/h
Y =up to 300 km/h.
Maximum speed rating
for snow tyres
Q M + S =up to 160 km/h.
T M + S =up to 190 km/h.
H M + S =up to 210 km/h.UNDERSTANDING RIM
MARKINGS
The following are the necessary in-
structions to understand the meaning
of the markings on the rim, as shown
in fig. 6a.RIM PROTECTOR TYRES
fig. 6b
Example: 6 1/2J x 15 H2 ET43
fig. 6b
F0B0510b
fig. 6a
F0B0267b
6 1/2=rim width in inches 1-fig. 6a;
J =rim drop centre outline (side
projection where the tyre bead rests)
2-fig. 6a;
15 =rim nominal diameter in inches
(corresponds to diameter of the tyre
to be mounted) 3-fig. 6a;
H2 =“hump” shape and number (re-
lief on the circumference holding the
Tubeless tyre bead on the rim);
ET43 =wheel camber angle (dis-
tance between the disc/rim support-
ing plane and the wheel rim centre
line).If after-sale tyres with
rim protector are used
(fig. 6b) and the car has
integral cups fixed (by springs) to
the sheet wheel, DO NOT fit
wheel cups. The use of unsuitable
tyres and wheel cups could cause
a sudden pressure loss of the ty-
re.
214-233 ULYSSE ING:214-233 ULYSSE ING 13-11-2009 10:21 Pagina 224

TECHNICAL SPECIFICATIONS
225
The plate on the front left door fig. 7carries the following data: A -empty
vehicle tyre inflation pressure; B -fully loaded vehicle tyre inflation pressure;
C-tyre dimension; D -rim dimension; E -type of tyre fitted; F -vehicle man-
ufacturing date identification code; G -spare box; H -paint colour code; I-ser-
ial number.
fig. 7
F0B0264b
Rims (*)
Tyres
Spare wheel
(*) Steel or alloy on request.
Rear
3.4
3.0 Front
2.5
2.5 Rear
2.5
2.5 Front
2.5
2.5Empty Full load Tyre
205/60 R16
215/65 R15standard size with steel rim2.0 JTD - 2.2 JTD
6.5J x 15”
7J x 16”
215/65 R15
215/60 R16
COLD TYRE INFLATION PRESSURE
Add +0.3 bars to the prescribed inflation pressure when the tyres are warm. In
any case, check the correct value again when the tyres are cold.
214-233 ULYSSE ING:214-233 ULYSSE ING 13-11-2009 10:21 Pagina 225

TECHNICAL SPECIFICATIONS
226
DIMENSIONS
The sizes are in mm and refer to the
car fitted with standard tyres.
Luggage compartment volume with
unladen vehicle (V.D.A. rules):
2948 dm
3.
fig. 8
F0B0457b
1759
2194/2205
214-233 ULYSSE ING:214-233 ULYSSE ING 13-11-2009 10:21 Pagina 226

TECHNICAL SPECIFICATIONS
227
PERFORMANCE
2.0 JTD
136 HP
190
11.4
33.0 2.0 JTD
120 HP
180
12.9
34.32.2 JTD
170 HP
200
10.0
31.42.2 JTD
170 HP a.g.
197
11.7
32.3
Max speed (*) km/h
Acceleration from 0 to 100 km/h sec.
Kilometre with standing start sec.
(*) Acceptable after the first period of use.
214-233 ULYSSE ING:214-233 ULYSSE ING 13-11-2009 10:21 Pagina 227

TECHNICAL SPECIFICATIONS
228
WEIGHTS
2.0 JTD 136 HP
6 5/7/8
seats seats
1854÷1957 1818÷1983
1256 1263
1274 1267
2530 2530
100 100
––
750 750
76 76
2.0 JTD 120 HP
6 5/7/8
seats seats
1846÷1949 1811÷1976
1253 1259
1277 1271
2530 2530
100 100
––
750 750
73 72
2.2 JTD 170 HP
6 5/7/8
seats seats
1902÷1988 1875÷2017
1304 1318
1266 1252
2570 2570
100 100
––
750 750
75 75
2.2 JTD 170 HP a.g.
6 5/7/8
seats seats
1930÷2016 1898÷2045
1336 1346
1274 1264
2610 2610
100 100
––
750 750
80 75
(kg)
Weight empty (including fluids,
90% fuel in the tank and
no optional)
Maximum allowed loads (1)
– front axle:
– rear axle:
– total:
Maximum load on roof:
Towable weight
– trailer with brakes:
– trailer without brakes:
Maximum load on ball coupling
(trailer with brakes):
(1) Loads not to be exceeded. The driver is responsible for arranging the loads so that they comply with these limits.
214-233 ULYSSE ING:214-233 ULYSSE ING 13-11-2009 10:21 Pagina 228

TECHNICAL SPECIFICATIONS
229
CAPACITIES
2.0 JTD
120 HP
litres
80
8
9
5.25
1.9
–
1.2
1.2
0.519
7.52.0 JTD
136 HP
litres
80
8
9
5.25
1.9
–
1.2
1.2
0.519
7.52.2 JTD
170 HP
litres
80
8
9
4.75
–
–
1.2
1.2
0.93
7.5
2.2 JTD
170 HP a.g.
litres
80
8
9
4.75
–
3/4
1.2
1.2
0.93
7.5
Fuel tank:
– including a reserve of:
Engine cooling system:
Engine sump and filter:
Transaxle:
Automatic gearbox
Hydraulic power steering:
Electro-hydraulic power steering
Hydraulic brake circuit with:
ABS (with ESP)
Windscreen, rear mirror and
headlight liquid reservoir:
Recommended fluids
and lubricants
Recommended products
Diesel for motor vehicles
(EN590 specifications)
Mixture of distilled water and
PARAFLU
UP(red) at 50%
SELENIA WR
TUTELA CAR EXPERYA
TUTELA GI/E
TUTELA GI/E
TUTELA GI/R
TUTELA TOP 4
50-50 mixture of distilled
water and TUTELA
PROFESSIONAL SC 35
214-233 ULYSSE ING:214-233 ULYSSE ING 13-11-2009 10:21 Pagina 229

TECHNICAL SPECIFICATIONS
230
FLUIDS AND LUBRICANTS
CHARACTERISTICS OF THE PRODUCTS
Use
For diesel engines, in case of emergency if original products are not available, lubricants with minimum performace ACEA B4 can be considered
acceptable; in this case no optimal performance of the engien can be assured and therefore we recommend to replace it as soon as possible
with the lubricant recommended by the Fiat Service Network.
Use of products with characteristics that are lower than ACEA B4 - SAE 5W-40 for Diesel engines, may damage the engine not under
warranty.
For weather conditions that are severe, ask the service network which product of the PETRONAS LUBRICANTS is more suitable.Original
fluids and lubricants
SELENIA WR
Contractual Technical
Reference N°F515.D06 Replacement
interval Fluid and lubricant quality characteristics C
for proper vehicel operation
Lubricants with synthetic base SAE 5W-40 grading
Qualification FIAT 9.55535-N2 Lubricants for
diesel engines
According to the
mainteance plan and
yearly inspection
214-233 ULYSSE ING:214-233 ULYSSE ING 13-11-2009 10:21 Pagina 230

TECHNICAL SPECIFICATIONS
231
Use
AVVERTENZA Non rabboccare o miscelare con altri liquidi aventi caratteristiche diverse da quelle descritte.Replacement
interval
Transmissions and
differentials mechanical
Hydraulic power steering
Automatic transmission
electronic
Homokinetic joints on
wheel side
Hydraulic brakes and
clutch hydraulic controls
Cooling circuits
Percentage of use:
'50% water
50% PARAFLU
UP
To mix with diesel fuel
(25cc per 10 litri)
To use pure
or diluted in the systems
of windshield wipers Original
fluids and lubricants
TUTELA CAR
EXPERYA
Contractual Technical
Reference N° F178.B06
TUTELA GI/E
Contractual Technical
Reference N° F001.C94
TUTELA ALL STAR
Contractual Technical
Reference N° F702.G07
TUTELA TOP 4
Contractual Technical
Reference N° F001.A93
PARAFLU
UP
Contractual Technical
Reference N° F101.M01
TUTELA DIESEL ART
Contractual Technical
Reference N° F601.L06
TUTELA
PROFESSIONAL
SC 35
Contractual Technical
Reference N° F201.D02 Quality characteristics of the fluids and lubricants
for proper vehicle operation
Synthetic lubricant with SAE 75W-80 grading
Exceeds API GL-4 specifications
Qualification FIAT 9.55550-MZ2.
Lubricant for automatic transmissions
Exceeds "ATF DEXRON III" specifications
Qualification FIAT 9.55550-AG2.
Molybdenum sulphur compound grease,
for high temepratures, Consistency NLGI 1-2
Qualification FIAT 9.55580.
Synthetic fluid for brake and clutch systems
Exceeds specifications: FMVSS n° 116 DOT 4,
ISO 4925, SAE J 1704
Qualification FIAT 9.55597.
Protective with antifreeze action red with base of
Glycol mono ethyl inhibited with organic formulation
Exceeds specifications CUNA NC 956-16, ASTM D 3306
Qualification FIAT 9.55523.
Additive for diesel fuel wih protective action for Diesel engines
Mix of alcohol and tensioactives CUNA NC 956-11,
Qualification FIAT 9.55522. Lubricants and
greases for the
motion
transmission
Liquid for brakes
Protective
for radiators
Fuel additive
Liquid for rwind-
shield wiper and
rear window wiper
214-233 ULYSSE ING:214-233 ULYSSE ING 13-11-2009 10:21 Pagina 231