2009 FIAT SEDICI warning

78
SERVICE VEHICLE SOON (SVS)
LIGHT (for Diesel Engine Model)
84E034
When the ignition switch is turned to the
“ON” position, this light comes on briefly
to let you know the light is working.
If this light blinks with the ignition switch
turned “ON”, the engine will not start.
NOTE If this light blinks, turn the ignition
switch to the “LOCK” position, then turn
it back to the “ON” position. If the light still
blinks with the ignition switch turned to the
“ON” position, there may be something
wrong with the immobilizer system. Ask to
you Fiat Dealership to inspect the system. MALFUNCTION INDICATOR
LIGHT
65D530
Your vehicle has a computer-controlled
emission control system. A malfunction in-
dicator light is provided on the instrument
cluster to indicate when it is necessary to
have the emission control system serviced.
The malfunction indicator light comes on
when the ignition switch is turned to the
“ON” position to let you know the light
is working and goes out when the engine
is started.
If the malfunction indicator light comes on
or blinks when the engine is running, ser-
vice to the emission control system is nec-
essary. Bring the vehicle to your FIAT
Dealership to have the emission control
system serviced right away and avoid hard
acceleration until the service is performed.
IMPORTANT Continuing to drive the ve-
hicle when the malfunction indicator light
is on or blinking can cause permanent
damage to the vehicle’s emission control
system, and can affect fuel economy and
driveability. TRANSAXLE WARNING LIGHT
(for versions/markets, where provided)
81A262
This light comes on for several seconds
when the ignition switch is turned to the
“ON” position so you can check the light
is working. If this light comes on, there is
the problem with the transaxle system.
Ask your Fiat Dealership to have the sys-
tem inspected.
071-128 SEDICI LUM FL GB 1E 19-06-2009 12:05 Pagina 78

79
FUEL FILTER WARNING LIGHT
(for Diesel Engine Model)
60A541
This light comes on for several seconds
when the ignition switch is turned to the
“ON” position so you can check that light
is working.
If the light comes on when driving, there
is a possibility to have water in the fuel
filter. Drain water as soon as possible. For
details of draining water, refer to “Fuel Fil-
ter” in the “INSPECTION AND MAIN-
TENANCE” section.
IMPORTANT The presence of water in
the fuel circuit may cause serious damage
to the entire injection system and cause
irregular engine operation. If the warning
light turns on contact Fiat Dealership as
soon as possible to have the system re-
lieved. If the above indications come on
immediately after refuelling, water has
probably been poured into the tank: turn
the engine off immediately and contact
Fiat Dealership. FIAT CODE SYSTEM LIGHT
(IMMOBILIZER)
(for versions/markets, where provided)
65D239
When the ignition switch is turned to the
“ON” position, this light comes on to let
you know the light is working.
If this light blinks with the ignition switch
turned to “ON”, the engine will not start.
NOTE If this light blinks, turn the ignition
switch to the “LOCK” position, then turn
it back to the “ON” position. If the light
still blinks with the ignition switch turned
to the “ON” position, there may be some-
thing wrong with the immobilizer system.
Ask to you Fiat Dealership to inspect the
system.
54G345
OVERHEAT INDICATOR LIGHT
(for Diesel Engine Model)
This light comes on for several seconds
when the ignition switch is turned to the
“ON” position so you can check that light
is working.
If this light comes on while driving, it may
mean engine overheat. Refer to “Tem-
perature Gauge/Overheat Indicator Light”
section.
GLOW PLUG INDICATOR LIGHT
(for Diesel Engine Model)
60A534
If the coolant temperature is cool enough,
this light comes on when the ignition
switch is turned on and goes out when the
glow plug is heated enough for engine
starting.
071-128 SEDICI LUM FL GB 1E 19-06-2009 12:05 Pagina 79

80
79J039
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started.
If this light comes on while driving, the
power steering system may not work
properly. Have the system inspected by
your Fiat Dealership.
NOTE If the power steering system does
not work properly, you will feel heavier
to steer but you still will be able to steer. ELECTRIC POWER STEERING
LIGHT
(for versions/markets, where provided)
LOW FUEL WARNING LIGHT
54G391
This light remains on until all doors (in-
cluding the rear door) are completely
closed.
If any door (including the tailgate) is open
when the vehicle is moving, a ding sounds
to remind you to close all doors com-
pletely.
54G343
If this light comes on, fill the fuel tank im-
mediately. OPEN DOOR WARNING LIGHTWhen this light comes on, a ding sounds
once to remind you to fill the fuel. If you
do not fill the fuel, a ding sounds every
time when the ignition switch is turned to
“ON”.
NOTE The activation point of this light
varies depending on road conditions (for
example, slope or curve) and driving con-
ditions because of fuel moving in the tank. DIESEL PARTICULATE FILTER
WARNING LIGHT
(for Diesel Engine Model)
64J244
This light comes on for several seconds
when the ignition switch is turned to the
“ON” position so you can check that light
is working.
If the light comes on when driving, the
diesel particulate filter is nearly clogged.
To regenerate the diesel particulate filter,
you must drive the vehicle until the light
goes out, at a speed of 50 km/h (31 mph)
or higher for a while (max. 30 minutes de-
pending on the vehicle speed).
If you drive your vehicle until the light goes
out, the regeneration of the diesel partic-
ulate filter will be completed.
For details, refer to “Diesel Particulate Fil-
ter” in the “OPERATING YOUR VEHI-
CLE” section.
071-128 SEDICI LUM FL GB 1E 19-06-2009 12:05 Pagina 80

81
MAIN BEAM (HIGH BEAM)
INDICATOR LIGHT
50G055
64J045When you turn on the left or right turn
signals, the corresponding green arrow on
the instrument cluster will flash along with
the respective turn signal lights. When you
turn on the hazard warning switch, both
arrows will flash along with all of the turn
signal lights.
50G056
This indicator comes on when headlight
main beams (high beams) are turned on. TURN SIGNAL INDICATORS KEYLESS START SYSTEM
INDICATOR LIGHT
(for versions/markets, where provided)
80JM122
When you push the ignition switch for ve-
hicle with the keyless start system, this
light will come on in blue or red. If this
light comes on in blue, you can turn the
ignition switch without using an ignition
key. If this light comes on in red, you can
not turn the ignition switch without us-
ing an ignition key. For details, refer to “Ig-
nition Switch” in the “STEERING COL-
UMN CONTROLS” section.
If this light blinks in red, it reminds you that
the remote controller is not in the vehi-
cle. For details, refer to “Keyless Start Sys-
tem” in the “BEFORE DRIVING” section.REAR FOG LIGHT INDICATOR
LIGHT
(for versions/markets, where provided)
54G491
The rear fog light indicator light comes on
when the rear fog light operates. ILLUMINATION INDICATOR
LIGHT
This indicator light comes on while the po-
sition lights, tail light and/or the headlights
are on.
071-128 SEDICI LUM FL GB 1E 19-06-2009 12:05 Pagina 81

84
If the low fuel warning light (1) comes on,
fill the fuel tank immediately.
When the low fuel warning light (1) comes
on, a ding sounds once to remind you to
fill the fuel.
If you do not fill the fuel, a ding sounds
every time when the ignition switch is
turned to “ON”.
NOTE The activation point of the low fu-
el warning light (1) varies depending on
road conditions (for example, slope or
curve) and driving conditions because of
fuel moving in the tank.
The mark (2) indicates that the fuel filler
door is located on the left side of the ve-
hicle.TACHOMETER
The tachometer indicates engine speed in
revolutions per minute.
IMPORTANT Never drive with the en-
gine speed indicator in the red zone or se-
vere engine damage can result. When
downshifting to a lower gear, make sure
not to operate with excessive revolution
speeds of the engine. Refer to “Down-
shifting maximum allowable speeds” in the
“OPERATING YOUR VEHICLE” section.
NOTE The indicator moves a little de-
pending on road conditions (for example,
slope or curve) and driving conditions be-
cause of fuel moving in the tank.
(2)
(1)
80JM102
79JM001
FUEL GAUGE
When the ignition switch is in the “ON”
position, this gauge gives an approximate
indication of the amount of fuel in the fu-
el tank. “F” stands for full and “E” stands
for empty.
If the indicator gets off the graduation of
“E” (not character “E”), refill the tank as
soon as possible.
071-128 SEDICI LUM FL GB 1E 19-06-2009 12:05 Pagina 84

86
Do not attempt to adjust the
display while driving.
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
WARNING
NOTE When you reconnect the negative
(–) terminal to the battery, the indication
of the instantaneous fuel consumption will
be reinitialized. Change the indication
again to your preference.
Trip meter / Average Fuel
Consumption / Driving Range /
Thermometer / Oil Life
Monitoring
When the ignition switch is in the “ON”
position, the display (B) shows one of the
following six indications, trip meter A, trip
meter B, average fuel consumption, dri-
ving range, thermometer or oil life moni-
toring.
To switch the display indication (B), push
the trip meter selector knob (1) or the in-
dicator selector knob (2) quickly.
80JM105
80JM106
❒Change the display (B) to the driving
range by pushing the indicator selec-
tor knob (2).
❒While pushing and holding the trip me-
ter selector knob (1), turn the indica-
tor selector knob (2) to turn off or on
the indication of instantaneous fuel
consumption. NOTE
❒The display does not show the bar
graph unless the vehicle is moving.
❒The indicated maximum value of in-
stantaneous fuel consumption is 30.
No more than 30 will be indicated on
the display even if the actual instanta-
neous fuel consumption is higher.
❒The indication on the display may be
delayed if fuel consumption is greatly
affected by driving conditions.
❒The display shows estimated values.
Indications may not be the same as ac-
tual values.
❒You can change the units that instan-
taneous fuel consumption is displayed
in. Refer to “Average fuel consump-
tion” in this section.
You can turn off or on the indication of in-
stantaneous fuel consumption according
to the following instruction.
071-128 SEDICI LUM FL GB 1E 19-06-2009 12:05 Pagina 86

87
a.Trip meter A
b.Trip meter B
c.Average fuel consumption
d.Driving range
e.Thermometer
f.Oil life monitoring
(a)
(b)
(c)
(d)
(e)
(f)
79JM009
ASPush the trip meter selector knob (1).
QZPush the indicator selector knob (2).
Do not attempt to adjust the
display while driving.
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
WARNING
NOTE
❒Indications will change when you push
and release a knob.
❒The display shows estimated values.
Indications may not be the same as ac-
tual values.
Trip meter
The trip meter can be used to measure
the distance traveled on short trips or be-
tween fuel stops.
You can use the trip meter A or trip me-
ter B independently.
To reset the trip meter to zero, push and
hold the trip meter selector knob (1) for
a while when the display shows the trip
meter.
NOTE The indicated maximum value of
the trip meter is 9999.9. When you run
past the maximum value, the indicated val-
ue will return to 0.0.Average fuel consumption
If you selected average fuel consumption
the last time you drove the vehicle, the
display shows the last value of average fu-
el consumption from previous driving
when the ignition switch is turned to the
“ON” position. Unless you reset the val-
ue of average fuel consumption, the dis-
play indicates the value of average fuel
consumption which includes average fuel
consumption during previous driving.
To reset the average fuel consumption to
zero, push and hold the indicator selector
knob (2) for a while when the display
shows the average fuel consumption.
NOTE When you reset the indication or
reconnect the negative (–) terminal to the
battery, the value of average fuel con-
sumption will be shown after driving for
a while.
To change the unit of average fuel con-
sumption, while pushing and holding the
trip meter selector knob (1), turn the in-
dicator selector knob (2).
071-128 SEDICI LUM FL GB 1E 19-06-2009 12:05 Pagina 87

88
Driving range
If you selected driving range the last time
you drove the vehicle, the display indicates
“---” for a few seconds and then indicates
the current driving range when the igni-
tion switch is turned to the “ON” posi-
tion.
The driving range shown in the display is
the approximate distance you can drive
until the fuel gauge indicates “E”, based on
current driving conditions.
When the remaining fuel in fuel tank
reaches a low level, the display “---” will
appear.
If the low fuel warning light comes on, fill
the fuel tank immediately regardless of the
value of driving range shown in the display.
As the driving range after refueling is cal-
culated based on the most recent driving
condition, the value is different each time
you refuel.
NOTE If you refuel when the ignition
switch is in the “ON” position, the driving
range may not indicate the correct value.
When you reconnect the negative (–) ter-
minal to the battery, the value of driving
range will be shown after driving for a
while.Thermometer
The thermometer indicates the outside
temperature.
If the outside temperature nears freezing,
the mark (g) will appear on the display.
NOTE The outside temperature indica-
tion is not the actual outside temperature
when driving at low speed, or when
stopped.
If there is something wrong with the ther-
mometer, or just after the ignition switch
is turned to the “ON” position, the dis-
play may not indicate the outside tem-
perature.
The mark (g) will appear whenever the
outside temperature is near freezing, even
if the display does not show the ther-
mometer.
To change the unit of temperature, while
pushing and holding the trip meter selec-
tor knob (1), turn the indicator selector
knob (2).(g)
79JM010
80JM137
NOTE Depending on the vehicle’s speci-
fication, the fuel consumption units of ini-
tial setting are indicated as km/L or
L/100km.
NOTE
❒When you change the units that av-
erage fuel consumption is displayed in,
the instantaneous fuel consumption
units will be changed automatically.
❒When you reconnect the negative (–)
terminal to the battery, the unit of the
average fuel consumption will be reini-
tialized. Change the unit again to your
preference.
071-128 SEDICI LUM FL GB 1E 19-06-2009 12:05 Pagina 88