2009 FIAT PANDA warning lights and messages

147KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0673m
fig. 136
F0Z0698m
fig. 137
❒
if after this operation it is still not possible to reach at
least 1.8 bar after five minutes, do not start driving since
the tyre is excessively damaged and the fast tyre re-
pair kit cannot guarantee suitable sealing. Contact
a Fiat Dealership;
❒
if the tyre reaches the pressure specified in “Inflation
pressure” paragraph in the “Technical Specifications”
chapter, start driving immediately;
Apply the adhesive label in a position
clearly visible by the driver as a reminder
that the tyre has been treated with the quick re-
pair kit. Drive carefully, particularly on bends. Do
not exceed 80 km/h. Do not accelerate and brake
suddenly.
WARNING
❒
after driving for about 10 minutes stop and check the
tyre pressure again; remember to engage the handbrake;
If the pressure falls below 1.8 bar, do not
drive any further: the quick tyre repair kit
Fix & Go automatic cannot guarantee proper hold
because the tyre is too much damaged. Contact
a Fiat Dealership.
WARNING
❒
if at least 1.8 bar pressure is read, restore proper pres-
sure (with engine running and handbrake on) and
restart;
❒
drive with the utmost care to the nearest Fiat Dealer-
ship.
135-168 PANDA EN 7-10-2009 14:07 Pagina 147

148KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0699m
fig. 138
F0Z0676m
fig. 139
BOTTLE REPLACEMENT PROCEDURE
To replace the bottle, proceed as follows:❒
disconnect the connection A-fig. 139;
❒
turn the bottle counter-clockwise to replace and raise
it;
❒
fit the new bottle and turn it clockwise;
❒
secure the connection A to the bottle and fit the trans-
parent tube B in the relevant compartment.
Absolutely inform the dealership that the
tyre has been repaired using the quick tyre
repair kit. Hand the instruction brochure over to
the personnel charged with treating the tyre re-
paired with the kit.
WARNING
FOR CHECKING AND RESTORING PRESSURE
ONLYThe compressor can be also used just for restoring pres-
sure. Release the bottle connection A-fig. 139 and connect
it directly to the tyre valve fig. 138; in this way the bottle
is not connected to the compressor anymore and the seal-
ing fluid will not flow into the tyre.
135-168 PANDA EN 7-10-2009 14:07 Pagina 148

149KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CHANGING A BULBGENERAL INSTRUCTIONS❒
Before changing a bulb check the contacts for oxidation;
❒
burnt bulbs must be replaced by others of the same type
and power;
❒
always check the headlight beam aiming after changing
a bulb;
❒
when a light is not working, check that the corre-
sponding fuse is intact before changing a bulb. For the
location of fuses, refer to the paragraph “Replacing fus-
es” in this chapter.
Modifications or repairs to the electric sys-
tem that are not carried out properly or
do not take the system technical specifications in-
to account can cause malfunctions leading to the
risk of fire.
WARNING
Halogen bulbs contain gas under pressure;
if they break, glass fragments may be dis-
persed.
WARNING
When handling halogen bulbs, only touch
the metal part. If the transparent bulb is
touched with the fingers, its lighting inten-
sity is reduced and life of the bulb may be com-
promised. In the event of accidental contact, wipe
the bulb with a cloth moistened with alcohol
and leave it to dry.
IMPORTANT The headlight inner surface might be slight-
ly misted: this should not be considered irregular rather
a natural phenomenon due to low temperature and the air
humidity level. Misting will disappear as soon as the head-
lights are turned on. The presence of drops inside the
headlights indicates infiltration of water. Contact a Fiat
Dealership.
Where possible, it is advisable to have bulbs
changed at a Fiat Dealership. The correct
operation and aiming of the outer lights are
absolutely important to the safety of the car and
its passengers and the subject of specific laws about
road traffic.
135-168 PANDA EN 7-10-2009 14:07 Pagina 149

150KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0118m
fig. 140
TYPES OF BULBS fig. 140
Various types of bulbs are fitted to your car:
A Glass bulbs: they are pressure-fit. Pull to remove.
B Bayonet-type bulbs: to remove this type of bulb from
its holder, press the bulb and turn it counter-clockwise.
C Tubular bulbs: release them from their contacts to re-
move.
D Halogen bulbs: to remove the bulb, release the clip
holding the bulb in place.
E Halogen bulbs: to remove the bulb, release the clip
holding the bulb in place.
135-168 PANDA EN 7-10-2009 14:07 Pagina 150

151KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
H4
H4
W5W
PY21W
W5W
PY21W
P21/5W
P21W
P21W
C5W
W5W
C5W
H1
W5W
60/55
60/55
5
21
5
21
21/5
21
21
5
5
5
55
5
D
D
A
B
A
B
B
B
B
C
A
C
E
A
Bulbs Type Power Re. figure 140Main beamDipped beamFront side lightsFront direction indicatorsSide direction indicatorsRear direction indicatorsStop/tail lightsReversing lightsRear fog lightsCeiling lightBoot lightNumber plate lightFog lightsThird stop
135-168 PANDA EN 7-10-2009 14:07 Pagina 151

152KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0089m
fig. 141
F0Z0091m
fig. 143
F0Z0090m
fig. 142
To change the direction indicator bulb, proceed as follows:❒
release the clip A-fig. 141 and remove the cap B;
❒
turn the bulb-holder D-fig. 142 and remove it (it is pres-
sure-fit);
CHANGING AN EXTERIOR LIGHTFor the type of bulb and power rating, see “Changing
a bulb”.
FRONT LIGHT UNIT
To change the side light bulb, proceed as follows:❒
release the clip A-fig. 141 and remove the cap B;
❒
turn the bulb-holder C-fig. 142 and remove it (it is pres-
sure-fit);
❒
remove the burnt bulb E-fig. 143 and fit the new one;
❒
refit by reversing the above mentioned operations.
135-168 PANDA EN 7-10-2009 14:07 Pagina 152

153KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0092m
fig. 144
F0Z0094m
fig. 146
F0Z0093m
fig. 145
❒
remove the burnt bulb F-fig. 144 and fit the new one;
❒
refit by reversing the above mentioned operations.
To replace the main/dipped beam light bulb, proceed as
follows:
❒
release the clip A-fig. 141 and remove the cap B;
❒
remove the connector G-fig. 145;
❒
release the bulb-holder clip H-fig. 145;
❒
remove the burnt bulb I-fig. 146 and fit the new one;
❒
refit by reversing the above mentioned operations.
135-168 PANDA EN 7-10-2009 14:07 Pagina 153

154KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0095m
fig. 147
F0Z0227m
fig. 149
F0Z0604m
fig. 148
FRONT FOG LIGHTS
(for versions/markets where provided)
To change the halogen bulb, proceed as follows:❒
undo the two screws A and B-fig. 149 for fog light fas-
tening on the bumper and take out trim and fog light,
disconnecting the connector;
❒
loosen the cover C-fig. 150 and remove the connec-
tor D;
❒
release the clip E-fig. 151 and remove the bulb F;
❒
refit by reversing the above mentioned operations. SIDE DIRECTION INDICATORS
To change the bulb, proceed as follows:
❒
push the lamp lens A-fig. 147 in the car running direc-
tion (it is pressure-fit);
❒
remove the bulb B-fig. 148 and replace it;
❒
remove the lamp lens.
135-168 PANDA EN 7-10-2009 14:07 Pagina 154