2009 FIAT IDEA wheel

180
STARTING
AND DRIVING
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
INTERIORS
Periodically check that water is not trap-
ped under the mats (due to water drip-
ping off shoes, umbrellas, etc.) which could
cause oxidisation of the sheet metal.
CLEANING SEATS AND FABRIC
PARTS
Remove dust with a soft brush or a va-
cuum cleaner. It is advisable to use a moi-
st brush on velvet upholstery.
Rub the seats with a sponge moistened
with a solution of water and neutral de-
tergent.
LEATHER SEATS
Remove dry dirt with a moist chamois
leather or cloth without pressing too hard.
Remove stains of liquid or grease with a
dry absorbing cloth. Do not rub. Then wi-
pe with a soft cloth or chamois leather
dipped in water and mild soap.
Use specific products for persistent stains
paying attention to instructions for use.
IMPORTANT Never use alcohol. Make
sure that the products used do not con-
tain alcohol or derivates, even in low con-
centrations. INTERIOR PLASTIC PARTS
It is advisable to clean interior parts with
a moist cloth and a solution of water and
mild soap. Use specific products for clea-
ning plastic, without solvents and specifi-
cally designed to prevent damage to the
appearance and colour of the treated parts
to remove grease and tough stains.
IMPORTANT Never use spirit or petro-
leum to clean the instrument panel tran-
sparent cover or other plastic parts.
Do not keep aerosol cans in
the car: risk of explosion. Ae-
rosol cans must not be exposed to a
temperature exceeding 50°C. When
the vehicle is exposed to sunlight, in-
ner temperature can greatly exceed
this value.
WARNING
The fabric upholstery of your
car is designed to withstand
the normal wear and tear of
your car for a long time. So-
me precautions are however needed.
Avoid prolonged rubbing against
clothing accessories, such as metal
buckles, Velcro strips and the like, whi-
ch by applying a high pressure on the
fabric in a small area could cause the
breakage of some threads and damage
the upholstery.
LEATHER STEERING
WHEEL/GEAR KNOB
These components must be cleaned with
mild soap and water only. Never use spi-
rit and/or alcohol based products. Read
the product label carefully before using
specific products for cleaning the interiors:
make sure the product does not contain
alcohol or alcohol based substances.
If window cleaner accidentally drips onto
the steering wheel or gear lever knob, wi-
pe away immediately and then wash the
concerned area with mild soap and water.
IMPORTANT Be careful when arranging
a steering wheel lock device, where ap-
plicable, to prevent damaging the leather
upholstery by rubbing.

181
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
IDENTIFICATION DATA ................................................. 182
ENGINE CODES - BODYWORK VERSIONS ............. 184
ENGINE ................................................................................. 185
FUEL FEED/IGNITION ....................................................... 187
TRANSMISSION UNIT ...................................................... 187
BRAKES .................................................................................. 188
SUSPENSIONS ..................................................................... 188
STEERING SYSTEM ............................................................. 188
WHEELS ................................................................................. 189
DIMENSIONS ....................................................................... 193
PERFORMANCE .................................................................. 193
WEIGHTS .............................................................................. 194
CAPACITIES ......................................................................... 195
FLUIDS AND LUBRICANTS ............................................ 196
FUEL CONSUMPTION ...................................................... 198
CO
2EMISSIONS .................................................................. 199
T T
E E
C C
H H
N N
I I
C C
A A
L L
S S
P P
E E
C C
I I
F F
I I
C C
A A
T T
I I
O O
N N
S S

188
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
SUSPENSIONS
Front
Rear
(◊) Engine version for some versions/markets only1.2
16V - 1.48V (◊) - 1.416V- 1.3 Multijet - 1.6 Multijet
McPherson independent wheels
Semi-independent wheels interconnected by means of torque axle
STEERING SYSTEM
Type
Steering circle
(kerb to kerb) m
(◊) Engine version for some versions/markets only1.2
16V - 1.48V (◊) - 1.416V- 1.3 Multijet - 1.6 Multijet
Rack and pinion with electric power steering
10,0
BRAKES
Service brakes:– front
– rear
Parking brake
IMPORTANT Water, ice and salt sprinkled on the roads may deposit on the brake disks reducing braking efficiency the first time the brakes are
applied.
(◊) Engine version for some versions/markets only1.2
16V - 1.48V (◊)- 1.416V- 1.3 Multijet 70CV
Self-ventilating discs (257 mm x 22 mm)
Drum (203 mm x 38 mm)
Operated by hand lever, acting on
rear brakes1.3 Multijet 90 CV - 1.3 Multijet 95 CV
1.6 Multijet
Self-ventilating discs (284 mm x 22 mm)
1.3 Multijet 90 CV - 1.3 Multijet 95 CV: drum
(228 mm x 40 mm)
1.6 Multijet: disc (240 mm x 11 mm)
Operated by hand lever, acting on
rear brakes

189
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
fig. 5F0H0229m
WHEELS
RIMS AND TYRES
Pressed steel or alloy rims. Radial type tu-
beless tyres. All approved tyres are listed
in the Log Book.
IMPORTANT In the event of discrepan-
cies between the information provided on
this “Owner’s handbook” and the “Log
book”, consider the specifications shown
in the log book only.
Respect the prescribed size to ensure sa-
fety of the car in movement. Fit tyres of
the same make and type on all wheels.
IMPORTANT Do not use inner tubes
with Tubeless tyres.HOW TO READ TYRE DATA
Example: 185/65 R 14 86 T
185 = Nominal width (S, distance in mm
between sidewalls).
65 = Height/width ratio (H/S) as a per-
centage.
R = Radial tyre
14 = Rim diameter in inches (Ø).
86 = Load rating (capacity)
T = Maximum speed rating SPACE SAVER SPARE WHEEL
(where provided)
Pressed steel rim Tubeless tyre.
WHEEL GEOMETRY
Front wheel toe-in measured between
rims: 0 ±1 mm.
The values refer to the car in running or-
der.

190
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
Maximum speed rating
Q= up to 160 km/h.
R= up to 170 km/h.
S= up to 180 km/h.
T= up to 190 km/h.
U= up to 200 km/h.
H= up to 210 km/h.
V= up to 240 km/h.
W= up to 270 km/h.
Y= up to 300 km/h.HOW TO READ THE
RIM DATA
Example: 6 J x 14 ET 40
6 = rim diameter in inches (1).
j) = rim drop centre outline (side
projection where the tyre bead
rests) (2).
14 = rim nominal diameter in inches
(corresponds to diameter of the
tyre to be mounted) (3 = Ø).
ET = shape and number of humps (used
for withholding tubeless tyre
beads on the rim).
40 = wheel camber angle (distance
between the disc/rim supporting
plane and the wheel rim centre li-
ne). Load rating (capacity)
60= 250 kg 84= 500 kg
61= 257 kg 85= 515 kg
62= 265 kg 86= 530 kg
63= 272 kg 87= 545 kg
64= 280 kg 88= 560 kg
65= 290 kg 89= 580 kg
66= 300 kg 90= 600 kg
67 = 307 kg 91= 615 kg
68= 315 kg 92= 630 kg
69 = 325 kg 93= 650 kg
70 = 335 kg 94= 670 kg
71 = 345 kg 95= 690 kg
72= 355 kg 96= 710 kg
73= 365 kg 97= 730 kg
74 = 375 kg 98= 750 kg
75= 387 kg 99= 775 kg
76 = 400 kg 100= 800 kg
77= 412 kg
101= 825 kg
78= 425 kg 102= 850 kg
79= 437 kg 103= 875 kg
80= 450 kg 104= 900 kg
81= 462 kg 105= 925 kg
82= 475 kg 106= 950 kg
83= 487 kg

191
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
1.2 - 1.4
petrol version -
1.3 Multijet 70 CV
1.3 Multijet 90 CV -
1.3 Multijet 95 CV -
1.6 Multijet
(*) Optional alloy rim
(**) Tyres to which chains cannot be fitted
(***) WARNING: the 14” wheel can only be used on 1.2 - 1.4 petrol and 1.3 Multijet 70 CV versions with chassis number higher than 74500
RIMS
6J x 14” ET 40
6J x 15” ET 40 (*)
6 J x 16” ET 41 (alloy)
6J x 15” ET 40 (*)
6
1/2J x 16” ET 40 (alloy)
TYRES
Equipment
185/65 R14 86T
195/60 R15 88H
205/50 R16 87V (**)
195/60 R15 88H
205/50 R16 87V (**)
Winter
185/65 R14 86Q (M+S)
195/60 R15 88Q (M+S)
–
195/60 R15 88Q (M+S)
–
SPACE SAVER SPARE WHEEL
Rim
4B x 14” (***)
4B x 15”
4B x 15”
Pneumatic
135/80 B14 84M (***)
125/80 R15 95M
125/80 R15 95M
VERSIONS
alternatively

192
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
COLD TYRE INFLATION PRESSURES (bar)
ORIGINAL TYRES
Tyre size Medium load Full load
Front Rear Front Rear
185/65 R14 86H 2,2 2,1 2,3 2,3
195/60 R15 88H 2.2 2.1 2.3 (2.4 ▲) 2.3
205/50 R16 87V 2.2 2.1 2.3 (2.5 ▲) 2-3
▲1.6 Multijet versions only
SPACE SAVER SPARE WHEEL135/80 B14 84M 2.8125/80 R15 95M 4.2
Add +0.3 bar to the prescribed inflation pressure when the tyres are warm. Recheck pressure value with cold tyres.
With snow tyres, add +0.2 bar to the inflation pressure value prescribed for standard tyres.

197
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
Use
Motion transmission
lubricants and
grease
Brake fluids
Protective
agent for radiators
Additive for
diesel fuel
Windscreen/
rear window
washer fluid
(●)IMPORTANT Do not use fluids with different specifications for topping up or mixing.
(❒) When the vehicle is used under particularly harsh weather conditions, we recommend using a 60-40 mixture of PARAFLU UP and demine-
ralised water.Fluid and lubricant features
for correct car operation
All synthetic lubricant
SAE 75W-85 grade. Exceeding API GL-4 PLUS,
FIAT 9.55550 MIL-L- 2105 D LEV specifications.
ClassificationFIAT 9.55550-MX3
Transmission lubricant
“ATF DEXRON III”.
ClassificationFIAT 9.55550-AG2
Molybdenum disulphide grease for high temperatures.
NL.GI. 1-2 consistency
ClassificationFIAT 9.55580
Polyurea base synthetic grease for high temperatures.
NL.GI. 2-2 consistency
ClassificationFIAT 9.55580
Specific grease for low-friction coefficient
CV joints. NL.GI. 2- 2 consistency
ClassificationFIAT 9.55580
Synthetic fluid, F.M.V.S.S. n.116, DOT 4, ISO 4925,
SAE J-1704, CUNA NC 956-01
Classification FIAT 9.55597
Red protective with antifreeze action, based on inhibited
monoethylene glycol with organic formula based on O.A.T.
Passes CUNA NO 956-16, ASTM D 3306 specifications
Classification FIAT 9.55523
Additive for diesel fuel, protecting Diesel engines
Mixture of alcohol and surfactants CUNA NC 956-11
Classification FIAT 9.55522Genuine fluids and
lubricants
TUTELA CAR
TECHNYX
Contractual Technical
Reference
N° F010.B05
TUTELA CAR GI/E
Contractual Technical
Reference
N° F001.C94
TUTELA ALL STAR
Contractual Technical
Reference
N° F702.G07
TUTELA STAR 325
Contractual Technical
Reference
N° F301.D03
TUTELA STAR 700
Contractual Technical
Reference
N° F701.C07
TUTELA TOP 4
Contractual Technical
Reference
N° F001.A93
PARAFLU UP (●)
Contractual Technical
Reference
N° F101.M01
TUTELA DIESEL ART
Contractual Technical
Reference
N° F601.L06
TUTELA
PROFESSIONAL SC 35
Contractual Technical
Reference N° F201.D02Applications
Manual gearbox and dif-
ferential
Hydraulic power stee-
ring
Wheel side
constant velocity joint
CV joints on differential
side subject to high tem-
peratures (versions1.4
16v)
CV joints
on differential side
Hydraulic
brakes and clutch
Cooling circuit. 50-50 con-
centration to -35°C (❒).
Do not mix with product
of different type.
To be mixed with fuel oil
(25 cc per 10 litres)
To be used diluted or
undiluted in wind-
screen/rear window
washer/wiper systems