2009 DODGE RAM 2500 DIESEL wheel torque

These dual rear wheels should be tightened as follows:
1. Tighten the wheel nuts in the numbered sequence to a
snug fit.2. Retighten the wheel nuts in the same sequence to the
torques listed in the table. Go through the sequence a
second time to verify that specific torque has been
achieved. Retighten to specifications at 100 miles
(160 km) and after 500 miles (800 km).
It is recommended that wheel stud nuts be kept torqued
to specifications at all times. Torque wheel stud nuts to
specifications at each lubrication interval.
Wheel NutsAll wheel nuts should be tightened occasionally to elimi-
nate the possibility of wheel studs being sheared or the
bolt holes in the wheels becoming elongated. This is
especially important during the first few hundred miles/
kilometers of operation to allow the wheel nuts to
become properly set. All nuts should first be firmly
seated against the wheel. The nuts should then be
tightened to recommended torque. Tighten the nuts to
final torque in increments. Progress around the bolt
Tightening Pattern
WHAT TO DO IN EMERGENCIES 417
6

circle, tightening the nut opposite to the nut just previ-
ously tightened until final torque is achieved. Recom-
mended torques are shown in the following chart.Disc
WheelsType Nut Stud Size Torque
Ft. Lbs.Torque
Newton
Meters
Cone 9/16-18 120-150 160-200
Flanged 9/16-18 130-160 190-220To Stow The Flat Or Spare
WARNING!
A loose tire thrown forward in a collision or hard
stop could injure the occupants in the vehicle. Have
the deflated (flat) tire repaired or replaced immedi-
ately. Turn the wheel so that the valve stem is down. Slide the
wheel retainer through the center of the wheel and
position it properly across the wheel opening.
For convenience in checking the spare tire inflation, stow
with the valve stem toward the rear of the vehicle.
Attach the wheel wrench to the extension tube. Rotate the
winch mechanism until the wheel is drawn into place
against the underside of the vehicle. Continue to rotate
until you feel the winch mechanism slip, or click three or
four times. It cannot be overtightened. Push against the
tire several times to be sure it is firmly in place.
HOISTINGA conventional floor jack may be used at the jacking
locations. Refer to the graphics that show jacking loca-
tions. However, a floor jack or frame hoist must never be
used on any other parts or the underbody.
418 WHAT TO DO IN EMERGENCIES

Life of Tires.......................... 359
Load Capacity ..................... 350,351
Pressure Monitor System (TPMS) ........... 366
Pressure Warning Light .................. 197
Quality Grading ....................... 506
Radial .............................. 357
Replacement ......................... 359
Rotation ............................ 363
Safety ........................... 346,354
Sizes ............................... 347
Snow Tires ........................... 363
Spare Tire ........................... 408
Spinning ............................ 357
Tread Wear Indicators ................... 358
Wheel Mounting ...................... 409
Wheel Nut Torque ..................... 414
Tongue Weight/Trailer Weight .............. 389
Torque Converter Clutch .................. 259
Tow Hooks, Emergency ................... 422 Towing
............................... 383
24-Hour Towing Assistance ............... 101
Disabled Vehicle ....................... 422
Guide .............................. 389
Recreational .......................... 397
Weight .............................. 389
Towing Assistance ....................... 101
Traction .............................. 304
Traction Control ......................... 334
Trailer Sway Control (TSC) ................. 345
Trailer Towing .......................... 383
Cooling System Tips .................... 396
Hitches ............................. 388
Minimum Requirements ................. 390
Mirrors .............................. 85
Trailer and Tongue Weight ............... 389
Wiring .............................. 393
Trailer Towing Guide ..................... 389
Trailer Weight .......................... 389
INDEX 525
10

WaterDriving Through ...................... 305
Wheel and Wheel Trim .................... 454
Wheel and Wheel Trim Care ................ 454
Wheel Cover ........................... 414
Wheel Mounting ........................ 409
Wheel Nut Torque .................... 414,417
Winch ................................ 308
Accessories .......................... 312
Operation ........................... 313
Rigging Techniques ..................... 325
Usage .............................. 308 Wind Buffeting
....................... 33,161
Window Fogging ........................ 244
Windows .............................. 32
Power ............................... 32
Rear Sliding .......................... 174
Windshield Defroster ................76,235,238
Windshield Washers ................ 138,139,438
Fluid ............................... 438
Windshield Wiper Blades .................. 437
Windshield Wipers ....................... 138
Wiper Blade Replacement .................. 437
Wipers, Intermittent ...................... 138
INDEX 527
10