2009 Citroen BERLINGO FIRST RHD display
[x] Cancel search: displayPage 20 of 115
23INSTRUMENTS, CONTROLS and DISPLAYS-
E n g i n e o i l l e v e l i n d i c a t o r
When the ignition is switched on,
the engine oil level is indicated for
approximately 10 seconds, after the
s e r v i c e i n f o r m a t i o n .
F l a s h i n g o f t h e s i x s q u a r e s a n d d i s -
p l a y i n g o f " m a x " i n d i c a t e a s u r p l u s o f
o i l w h i c h c o u l d d a m a g e t h e e n g i n e .
I f t h e s u r p l u s o f o i l i s c o n fi r m e d b y
a c h e c k u s i n g t h e d i p s t i c k , c o n t a c t a
C I T R O Ë N d e a l e r w i t h o u t d e l a y .
Y o u r C I T R O Ë N d e a l e r c a r r i e s o u t
t h i s o p e r a t i o n a f t e r e a c h s e r v i c e .
T h e r e s e t p r o c e d u r e i s a s f o l l o w s :
- S w i t c h o f f t h e i g n i t i o n .
- P r e s s a n d h o l d b u t t o n
1 .
- S w i t c h o n t h e i g n i t i o n .
T h e d i s p l a y b e g i n s a 1 0 s e c o n d c o u n t -
d o w n .
-
K e e p b u t t o n 1 p r e s s e d f o r 1 0 s e c o n d s .
The display shows [= 0] and the span-
n e r d i s a p p e a r s .
Flashing of the six segments and dis-
playing of "min" indicate a lack of oil
w h i c h c o u l d d a m a g e t h e e n g i n e .
I f t h e l a c k o f o i l i s c o n fi r m e d b y a
c h e c k u s i n g t h e d i p s t i c k , i t i s e s s e n t i a l
t h a t t h e l e v e l i s t o p p e d u p . Flashing of the six segments indi-
c a t e s a m a l f u n c t i o n o f t h e o i l l e v e l
i n d i c a t o r .
T h e r e i s a r i s k o f d a m a g e t o t h e e n g i n e .
C o n s u l t a C I T R O Ë N d e a l e r .
T h e l e v e l r e a d o n t h e d i p s t i c k o r o n
t h e i n d i c a t o r w i l l o n l y b e c o r r e c t i f
t h e v e h i c l e i s o n l e v e l g r o u n d a n d
t h e e n g i n e h a s b e e n o f f f o r m o r e
t h a n 1 5 m i n u t e s .
R e s e t t i n g t h e s e r v i c e i n d i c a t o r
S u r p l u s o f o i l
L a c k o f o i l O i l l e v e l i n d i c a t o r f a u l t
Page 21 of 115
INSTRUMENTS, CONTROLS and DISPLAYS24 - B r i e fl y p r e s s i n g b u t t o n 1 alternates
between the total and trip distance
d i s p l a y s .
To reset the trip recorder to zero,
w h e n i t i s d i s p l a y e d p r e s s b u t t o n 1
u n t i l z e r o s a p p e a r .
T o t a l d i s t a n c e r e c o r d e r
W i t h t h e l i g h t s o n , p r e s s t h e b u t t o n
to vary the intensity of the lighting of
t h e i n s t r u m e n t s a n d c o n t r o l s . W h e n
t h e l i g h t i n g r e a c h e s t h e m i n i m u m ( o r
m a x i m u m ) s e t t i n g , r e l e a s e t h e b u t -
ton then press it again to increase (or
r e d u c e ) t h e b r i g h t n e s s .
A s s o o n a s t h e l i g h t i n g i s o f t h e r e q u i -
r e d b r i g h t n e s s , r e l e a s e t h e b u t t o n .
LIGHTING RHEOSTAT CLOCK
B u t t o n 1 : h o u r a d j u s t m e n t
B u t t o n 2 : m i n u t e a d j u s t m e n t
P r e s s a n d h o l d t h e b u t t o n f o r r a p i d
a d v a n c e .
Page 22 of 115
25INSTRUMENTS, CONTROLS and DISPLAYS-
DISPLAY A
This displays the following information:
- the time,
- the date,
- t h e a u d i o s y s t e m d i s p l a y s ,
- a d o o r c h e c k ( e . g . : ' ' l e f t f r o n t d o o r open''),
- w a r n i n g m e s s a g e s ( e . g . ' ' r e m o t e c o n t r o l b a t t e r y fl a t ' ' ) o r i n f o r m a t i o n
m e s s a g e s ( e . g . ' ' e c o n o m y m o d e
a c t i v e ' ' ) , d i s p l a y e d t e m p o r a r i l y . A d j u s t i n g t h e p a r a m e t e r s d i s p l a y A
P r e s s a n d h o l d b u t t o n
A for two sec-
onds to access the settings; the data
fl a s h e s , i n d i c a t i n g i t i s r e a d y t o b e
m o d i fi e d .
T h e n , e a c h p r e s s o f b u t t o n A scrolls
t h r o u g h t h e v a r i o u s d a t a i n t h e f o l -
lowing order:
- l a n g u a g e o f i n f o r m a t i o n d i s p l a y e d ,
- h o u r s ( 1 2 t h e n 2 4 h o u r m o d e ) ,
- m i n u t e s ,
- year,
- month,
- d a y .
P r e s s i n g b u t t o n B a l t e r s t h e v a l u e o f
t h e p a r a m e t e r s e l e c t e d . P r e s s a n d
h o l d f o r r a p i d a d v a n c e ( r e t u r n t o s t a r t
a f t e r t h e l a s t p o s s i b l e v a l u e ) .
After 7 seconds with no action, the
s t a n d a r d d i s p l a y r e t u r n s ; t h e m o d i fi e d
d a t a i s n o w r e c o r d e d .
Page 25 of 115
AUDIO EQUIPMENT28 - GENERAL FUNCTIONS AUDIO SETTINGS
Adjusting the loudness
This function automatically empha-
sises bass and treble tones. Press
button I or J to switch the function on
or off.
On/off
With the ignition key
in the accessories or
ignition position, press
button
A to switch the
set on or off.
The set can oper-
ate for 30 minutes
without the vehicle ignition being
switched on.
Anti-theft system
The audio system is coded in such a
way that it can operate only on your
v e h i c l e . I t w o u l d n o t f u n c t i o n i f fi t t e d
to another vehicle.
The anti-theft system is automatic
and requires no action on your
part.
ADJUSTING THE VOLUME Adjusting the bass
Adjusting the treble
When
"TREB" is displayed, press
button I or J to vary the setting.
- "TREB -9" for a minimum treble
setting,
- "TREB 0" for a normal setting,
- "TREB +9" for a maximum treble
setting.
Press button
H several
times in succession
to access the bass
(BASS) , treble (TREB) ,
loudness (LOUD) ,
fader (FAD) , balance
(BAL) and automatic
volume correction.
Exit from audio mode is automatic af-
ter a few seconds without pressing any
button, or by pressing button H after
c o n fi g u r a t i o n o f t h e a u t o m a t i c v o l u m e
correction.
Note: bass and treble settings are
s p e c i fi c t o e a c h s o u r c e . I t i s p o s s i b l e t o
set them differently for radio, cassette
(RB3) , CD (RD3) and CD changer. When
"BASS" is dis-
played, press button
I or J to vary the set-
ting.
- "BASS -9" for a
minimum bass set-
ting,
- "BASS 0" for a nor-
mal setting,
- "BASS +9" for a maximum bass
setting.
Press button C to in-
crease the volume, or
button B to decrease it.
Continuous pressure
on buttons C and B al-
lows a gradual adjust-
ment of the volume.
Page 26 of 115
29AUDIO EQUIPMENT-
RADIO
Adjusting the front/rear sound
distribution (Fader)
When
"FAD" is displayed, press but-
ton I or J .
Button I increases the volume in the
front.
Button J increases the volume in the
rear.
Adjusting the right/left sound
distribution (Balance)
When "BAL" is displayed, press but-
ton I or J .
Button I increases the volume on the
right-hand side.
Button J increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons I or J to switch the
function on or off. Selecting radio mode
Press button R .
Notes on radio reception
Your car radio is subject to phenom-
ena which do not affect domestic ra-
dio sets. Both AM (MW/LW) and FM
reception are subject to various forms
o f i n t e r f e r e n c e . T h i s i s n o r e fl e c t i o n o n
the quality of the equipment, but is due
to the nature of the signals and the way
in which they are transmitted.
On MW/LW, interference may be no-
ticed when passing under high voltage
power lines or bridges, or in tunnels.
On FM, interference may be the re-
sult of increasing distance from the
t r a n s m i t t e r , d e fl e c t i o n o f t h e s i g n a l s b y
obstacles (mountains, hills, buildings,
etc.), or of being in an area which is
not covered by a transmitter. Selecting a waveband
B r i e fl y p r e s s b u t t o n
R to select the FM1,
FM2, FMast and AM wavebands.
Page 27 of 115
29AUDIO EQUIPMENT-
RADIO
Adjusting the front/rear sound
distribution (Fader)
When
"FAD" is displayed, press but-
ton I or J .
Button I increases the volume in the
front.
Button J increases the volume in the
rear.
Adjusting the right/left sound
distribution (Balance)
When "BAL" is displayed, press but-
ton I or J .
Button I increases the volume on the
right-hand side.
Button J increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons I or J to switch the
function on or off. Selecting radio mode
Press button R .
Notes on radio reception
Your car radio is subject to phenom-
ena which do not affect domestic ra-
dio sets. Both AM (MW/LW) and FM
reception are subject to various forms
o f i n t e r f e r e n c e . T h i s i s n o r e fl e c t i o n o n
the quality of the equipment, but is due
to the nature of the signals and the way
in which they are transmitted.
On MW/LW, interference may be no-
ticed when passing under high voltage
power lines or bridges, or in tunnels.
On FM, interference may be the re-
sult of increasing distance from the
t r a n s m i t t e r , d e fl e c t i o n o f t h e s i g n a l s b y
obstacles (mountains, hills, buildings,
etc.), or of being in an area which is
not covered by a transmitter. Selecting a waveband
B r i e fl y p r e s s b u t t o n
R to select the FM1,
FM2, FMast and AM wavebands.
Page 28 of 115
AUDIO EQUIPMENT30 - B r i e fl y p r e s s b u t t o n L or N to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
T h e s c r o l l i n g s t o p s a t t h e fi r s t s t a -
tion found as soon as the button is
released.
If the TA t r a f fi c i n f o r m a t i o n p r o -
gramme is selected, only stations
broadcasting this type of programme
are selected.
S e a r c h i n g f o r a s t a t i o n o c c u r s fi r s t i n
"LO" sensitivity (selection of the most
powerful transmitters) during scan-
ning of the waveband, then in "DX"
sensitivity (selection of the weakest
and most distant transmitters).
To make a direct search in "DX" sen-
sitivity, press button L or N twice. Manual station search
Press the
"MAN" button.
B r i e fl y p r e s s b u t t o n L or N to increase
or decrease the frequency displayed.
By continuing to press the button in
the direction selected, you will obtain
continuous scrolling of the frequency.
T h e s c r o l l i n g s t o p s a t t h e fi r s t s t a t i o n
found as soon as the button is re-
leased.
Pressing the "MAN" button again re-
turns you to automatic station search.
Manual storing of stations in the
memory
Select the station required.
Press one of the buttons "1" to "6"
for more than two seconds.
The sound stops then becomes audi-
b l e a g a i n , c o n fi r m i n g t h a t t h e s t a t i o n
has been stored in the memory.
Automatic station search
Automatic storing of FM stations
in the memory (autostore)
Press and hold button
R for more than two
seconds.
Your radio automatically stores the
6 stations with the strongest signal in
FM . These stations are stored in the
FMast waveband.
I f i t i s n o t p o s s i b l e t o fi n d 6 s t a t i o n s ,
the remaining memories are empty.
Recalling stations stored in the
memory
F o r e a c h w a v e b a n d , b r i e fl y p r e s s
buttons "1" to "6" to recall the cor
responding station.
Page 29 of 115
31AUDIO EQUIPMENT-
RDS T r a f fi c i n f o r m a t i o n p r o g r a m m e
Regional following mode (REG)
RDS station following
The display indicates the name of the
station selected. The radio is contin-
ually searching for the station which
has the best reception and which is
transmitting the same programme. Press the
"TA" button
to switch the function
on or off.
B r i e fl y p r e s s t h e
"RDS" button to
switch the function on
or off.
The multi-function display will show:
- "RDS" if the function is selected.
- "(RDS)" if the function is selected
but not available. When they are part
of a network, certain
stations broadcast re-
gional programmes in
the various areas they serve. With re-
gional following mode you can keep
listening to the same programme.
Press the "RDS" button for more
than two seconds to switch the REG
function on or off.
Using the RDS (Radio Data
System) function on FM
Radio Data System allows you to
continue listening to the same sta-
tion, whatever frequency it is using
for the region you are going through.
N o t e : t h e v o l u m e o f t r a f fi c i n f o r m a -
tion announcements is independ-
ent of the volume of normal radio
listening. You can adjust it using
the volume button. The setting will
be stored and will be used when
the next messages are broadcast.
The multi-function display will show:
-
"TA" if the function is selected,
- "(TA)" if the function is selected
but not available.
A n y t r a f fi c i n f o r m a t i o n fl a s h w i l l b e
given priority, whatever source you
are listening to (radio, cassette, CD
or CD changer).
If you wish to interrupt a message,
press the "TA" button; this switches
the function off.