2009 CHRYSLER 300 C keyless

When the vehicle automatically transitions from AWD to
RWD the EVIC will display the following message for
five seconds.
Refer to “All Wheel Drive — If Equipped” in Section 5 for
more information on the All Wheel Drive (AWD) system.Keyless Go Display — If Equipped
When the ENGINE START/STOP button is pressed to
change ignition states, the Keyless Go icon momentarily
appears in the EVIC display showing the new ignition
state.
Keyless Go Display
All Wheel Drive (AWD) to Rear Wheel Drive (RWD)
232 UNDERSTANDING YOUR INSTRUMENT PANEL

“Remote Key Unlock”
WhenDriver Door 1st Pressis selected, only the driver’s
door will unlock on the first press of the Remote Keyless
Entry (RKE) transmitter UNLOCK button. When Driver
Door 1st Press is selected, you must press the RKE
transmitter UNLOCK button twice to unlock the passen-
ger’s doors. WhenAll Doors 1st Pressis selected, all of
the doors will unlock on the first press of the RKE
transmitter UNLOCK button. To make your selection,
press and release the FUNCTION SELECT button until
“Driver Door 1st Press” or “All Doors 1st Press” appears.
NOTE:If the vehicle is equipped with Passive Entry
and the EVIC is programmed to Unlock All Doors 1st
Press, all doors will unlock no matter which handle is
grasped. If Driver Door 1st Press is programmed, only
the driver ’s door will unlock when the driver ’s door is
grasped. With Passive Entry, if Driver Door 1st Press is
programmed touching the handle more than once will
only result in the driver ’s door opening. You have totouch a passenger handle to unlock all doors passively
when Driver ’s Door Only is programmed in the EVIC.
“Recall Memory with Remote Key Unlock” — If
Equipped
When ON is selected, you can use your RKE transmitter
to recall one of two pre-programmed memory profiles.
Each memory profile contains desired position settings
for the driver seat, side mirror, adjustable pedals (if
equipped), power tilt and telescopic steering column (if
equipped), and a set of desired radio station presets.
When OFF is selected, only the MEMORY switch on the
driver’s door trim panel will recall memory profiles. To
make your selection, press and release the FUNCTION
SELECT button until “ON” or “OFF” appears. Refer to
“Driver Memory Seat” in Section 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 237
4

STARTING AND OPERATING
CONTENTS
Starting Procedures.................... 313
▫Automatic Transmission............... 313
▫Keyless Go (If Equipped)............... 314
▫Normal Starting..................... 315
▫Extremely Cold Weather
(Below -20°F Or -29°C)................ 316
▫If Engine Fails To Start................ 316
▫After Starting....................... 318
Engine Block Heater — If Equipped........ 318Automatic Transmission................. 318
▫General Information.................. 319
▫Brake/Transmission Shift Interlock System . . 321
▫Brake/Transmission Interlock Manual
Override.......................... 321
▫4-Speed Automatic Transmission......... 323
▫5-Speed Automatic Transmission......... 328
AutoStick— If Equipped............... 332
▫AutoStickOperation................. 332
5

CAUTION!
Damage to the transmission may occur if the follow-
ing precautions are not observed:
•Shift into PARK only after the vehicle has come to
a complete stop.
•Shift into or out of REVERSE only after the
vehicle has come to a complete stop and the engine
is at idle speed.
•Do not shift from REVERSE, PARK, or NEUTRAL
into any forward gear when the engine is above
idle speed.
•Before shifting into any gear, make sure your foot
is firmly on the brake pedal.
Keyless Go (If Equipped)
This function allows the driver to op-
erate the ignition switch with the push
of a button, as long as the ENGINE
START/STOP button is installed and
the Keyless Go ignition key (FOBIK)
can be detected inside of the vehicle.
Removing and Re-Installing the Engine Start/Stop
Button
The ENGINE START/STOP button may be removed
from the receptacle to allow the vehicle ignition to be
controlled conventionally by inserting the FOBIK. The
button may be removed using the valet key from the
FOBIK as a thin tool. Insert the metal part of the valet key
under the chrome bezel at the 6 o’clock position, and
gently pry the button loose.
314 STARTING AND OPERATING

To reinstall the button, position it with its lettering
oriented horizontal and readable. Gently insert the but-
ton into the receptacle by pressing on the center of the
button. If the button slips in easily, it has been installed
correctly. Press firmly on the center of the button to seat
the button into the receptacle.
The ENGINE START/STOP button should only be re-
moved or inserted with the ignition in the OFF position.
Keyless Go Functions — With Driver ’s Foot Off
The Brake Pedal (In PARK Position)
•
Press the ENGINE START/STOP buttononce (ACC
position)to activate the radio, wipers, and windows.
•Press the ENGINE START/STOP buttontwice (ON
position)to activate the heating/air conditioning
(HVAC) controls, and the instrument cluster.
•Press the ENGINE START/STOP buttonthree times
(OFF position)to turn off the ignition switch.
Normal Starting
Using The ENGINE START/STOP Button
NOTE:Normal starting of either a cold or a warm
engine is obtained without pumping or depressing the
accelerator pedal.
To start the engine, the transmission must be in PARK or
NEUTRAL. From any ignition state, press and hold the
brake pedal while pressing the ENGINE START/STOP
button. The system takes over and attempts to start the
vehicle. If the vehicle fails to start, the starter will
disengage automatically after 10 seconds. If you wish to
stop the cranking of the engine prior to the engine
starting, press the button again.
Using Fob With Integrated Key (Tip Start)
NOTE:Normal starting of either a cold or a warm
engine is obtained without pumping or depressing the
accelerator pedal.
STARTING AND OPERATING 315
5

located to the right of the shift lever. The override access
port is at the top of the bin to the right of the shift lever
gate.To activate the override, first insert the key into the
ignition switch and turn it to the ON position. Then,
press the pink-colored tab through the access port with a
small flat blade screwdriver or alike. While pressing the
override, move the shift lever out of the PARK position.
When complete, return the rubber tray to its original
position.
With Keyless Go — If Equipped
To activate the override, with a valid keyfob (FOBIK)
inside of the vehicle, and without the brake pedal
pressed, press the START/STOP button once to go to the
ACC position, or twice to go to the ON position. Then,
press the pink-colored tab through the access port with a
small flat-bladed screwdriver or alike. While pressing the
override tab, move the shift lever out of the PARK
position. When complete, return the override cover to its
original position.
Interlock Manual Override
322 STARTING AND OPERATING

Auto Down Power Windows................ 38
Auto Unlock, Doors....................... 32
Auto Up Power Windows.................. 39
Automatic Dimming Mirror................. 90
Automatic Door Locks...................31,32
Automatic Headlights.................... 140
Automatic Oil Change Indicator........... 211,227
Automatic Temperature Control (ATC)......... 301
Automatic Transaxle
Special Additives...................... 453
Automatic Transmission...........323,328,452,453
Adding Fluid......................453,482
Autostick............................ 332
Fluid and Filter Changes................. 453
Fluid Change......................... 453
Fluid Level Check...................... 452
Fluid Type........................... 482
Gear Ranges.......................323,328
Overdrive........................... 325Shifting..........................323,328
Special Additives...................... 453
Torque Converter...................... 326
Automatic Transmission Limp Home
Mode...........................327,331,332
Autostick............................. 332
Axle Fluid............................. 482
Axle Lubrication (Axle Fluid)............... 482
Battery............................... 438
Emergency Starting..................... 417
Jump Starting......................... 417
Keyless Transmitter Replacement (RKE)....... 25
Location..........................418,438
Belts, Seat............................44,80
Body Mechanism Lubrication............... 441
B-Pillar Location........................ 353
Brake Assist System...................... 344
Brake Control System, Electronic............. 343
INDEX 513
10

Information Center, Vehicle................. 221
Inside Rearview Mirror.................... 89
Instrument Cluster....................208,210
Instrument Panel and Controls.............. 207
Instrument Panel Lens Cleaning............. 458
Integrated Power Module (Fuses)............ 459
Interior Appearance Care.................. 456
Interior Fuses.......................... 459
Interior Lights.......................... 146
Intermittent Wipers (Delay Wipers)........... 147
Introduction............................. 4
Jack Location........................... 406
Jack Operation.......................... 409
Jacking Instructions...................... 409
Jump Starting.......................... 417
Key, Programming........................ 17
Key, Replacement........................ 16Key, Sentry (Immobilizer)................... 15
Key-In Reminder......................... 15
Keyless Entry System...................... 20
Keyless Go.......................12,232,314
Keys................................. 12
Kicker Sound System..................... 292
Knee Bolster............................ 54
Lane Change and Turn Signals.............. 144
Lap/Shoulder Belts....................... 44
LATCH
(Lower Anchors and Tether for CHildren).....72,73
Latch Plate............................. 46
Latches................................ 81
Hood............................... 138
Lead Free Gasoline...................... 379
Leaks, Fluid............................ 81
Life of Tires............................ 363
Light Bulbs..........................81,467
INDEX 521
10