2009 CHERY TIGGO display

Downloaded from www.Manualslib.com manuals search engine INTERNATIONAL SYMBOLS
International Symbols
The graphic symbols illustrated in the following International Control and Display Symbols chart are used to identify var-
ious instrument controls. The symbols correspond to the controls and displays that are located on the instrument panel.
International Control and Display Symbols
1 - High Beam
2 - Fog Lamps
3 - Headlamp, Parking Lamps, Panel Lamps
4 - Turn Signals
5 - Hazard Warning
6 - Front Windshield Washer
7 - Front Windshield Wiper
8 - Front Windshield Wiper and Washer
9 - Front Windshield Defroster
10 - Blower Motor Fan
11 - Rear Window Defroster
12 - Rear Window Wiper13 - Rear Window Washer
14 - Fuel
15 - Engine Coolant Temperature
16 - Battery Charging Condition
17 - Engine Oil
18 - Seat Belt
19 - Brake Failure
20 - Parking Brake
21 - Hood
22 - Trunk
23 - Horn
24 - Cigarette Lighter
BESM010003
01
01–13Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Hardware Requirements
The hardware configuration of X-431 is as follows:
Diagnostic Scan Tool Configuration
ITEM NAMEFUNCTION
1 X-431 Main Unit To Display Operational
Buttons, Test Results, Help
Information, etc.
2 Mini-Printer To Print Test Results.
(Optional)
3 CF Card To Store Diagnostic Software
and Data
4 USB Cable To Connect CF Card
Reader/Writer and Computer
5 CF Card
Reader/Writer To Read or Write Data On
The CF Card
6 Mitsubishi-12+16
Pin Connector To Diagnose Mitsubishi
Electronic Control Systems
On Chery B11 Series
7 Fiat-3 Pin
Connector To Diagnose Vehicles With
Fiat-3 Pin Diagnostic
ConnectorITEM NAME
FUNCTION
8 Smart OBDII-16
Pin Connector To Diagnose Other Systems
Of Vehicle With OBDII-16
Pin Diagnostic Connector
9 Power Cord To Connect AC 100 - 240 V
Outlet and Power Adapter
10 Cigarette Lighter
Cable To Get Power From Vehicle
Cigarette Lighter
11 Battery Cable
W/Two Clips To Get Power From Vehicle
Battery
12 Power Adapter To Convert 100 - 240 V AC
Power Into 12 V DC Power
13 Main Cable To Connect The Diagnostic
Connector and Smartbox
14 Smartbox To Perform Vehicle
Diagnosis
GENERAL INFORMATION
BESM030003
03–8Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine P0506 - Idle Control System RPM Lower Than Expected
•Self-diagnosis detection logic.
DTC NO. DTC DEFINITION DTC DETECTION
CONDITION DTC SET
CONDITION POSSIBLE CAUSE
P0506 Idle control system
RPM lower than expected •
Engine is running.
• With the engine
idling in drive, the
brake applied,
engine run time
below a calibrated
minimum value, and
no VSS, MAF/MAP,
ECT, TPS, ETC,
Crankshaft Position
sensor, fuel system,
or injector DTCs
present. ECM detected that
the idle speed is less than the
acceptable range. •
Electronic throttle
control actuator
• Intake air leak
• ECM
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
• Turn ignition switch off.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on.
• With the scan tool, record and erase stored DTCs in the ECM.
• Start engine and warm it up to the normal operating temperature then select view DTC.
• If DTC is detected, go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnosis & Testing Diagnostic Help in Sec-
tion 03 Electronic Engine Controls).
NOTE :
If DTC P0506 is displayed with other DTCs, perform this diagnostic procedure before other DTCs.
NOTE :
While performing electrical diagnosis & testing, always refer to the electrical schematics for specific circuit
and component information.
DIAGNOSIS & TESTING
03
03–191Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Hardware Requirements
The hardware configuration of X-431 is as follows:
Diagnostic Scan Tool Configuration
ITEM NAMEDESCRIPTION
1 X-431 Main Unit To Display Operational
Buttons, Test Results, Help
Information, etc.
2 Mini-Printer To Print Test Results.
(Optional)
3 CF Card To Store Diagnostic Software
and Data
4 USB Cable To Connect CF Card
Reader/Writer and Computer
5 CF Card
Reader/Writer To Read or Write Data On
The CF Card
6 Mitsubishi-12+16
Pin Connector To Diagnose Mitsubishi
Electronic Control Systems
On Chery B11 Series
7 Fiat-3 Pin
Connector To Diagnose Vehicles With
Fiat-3 Pin Diagnostic
ConnectorITEM NAME
DESCRIPTION
8 Smart OBDII-16
Pin Connector To Diagnose Other Systems
Of Vehicle With OBDII-16
Pin Diagnostic Connector
9 Power Cord To Connect AC 100-240 V
Outlet and Power Adapter
10 Cigarette Lighter
Cable To Get Power From Vehicle
Cigarette Lighter
11 Battery Cable
W/Two Clips To Get Power From Vehicle
Battery
12 Power Adapter To Convert 100-240 V AC
Power Into 12 V DC Power
13 Main Cable To Connect The Diagnostic
Connector and Smartbox
14 Smartbox To Perform Vehicle
Diagnosis
DIAGNOSIS & TESTING
BESM030003
03
03–249Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine P0506 - Idle Control System RPM Lower Than Expected
On Board Diagnostic Logic
•Self-diagnosis detection logic.
• If DTC P0506 is displayed with other DTC, first perform the trouble diagnosis for the other DTC.
DTC NO. DTC DEFINITION DTC DETECTION
CONDITION DTC SET
CONDITION POSSIBLE CAUSE
P0506 Idle control system
RPM lower than expected •
Engine is running
• With the engine
idling in drive, the
brake applied,
engine run time
below a calibrated
minimum value, and
no VSS, MAF/MAP,
ECT, TPS, ETC,
Crankshaft Position
sensor, fuel system,
or injector DTCs
present. ECM detected that
the idle speed is less than the
acceptable range. •
Electronic throttle
control actuator
• Intake air leak
• ECM
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
• Turn ignition switch off.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on.
• With the scan tool, record and erase stored DTCs in the ECM.
• Start engine and warm it up to the normal operating temperature then select view DTC.
• If DTC is detected, go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnosis & Testing Diagnostic Help in Sec-
tion 03 Electronic Engine Controls).
NOTE :
While performing electrical diagnosis & testing, always refer to the electrical schematics for specific circuit
and component information.
DIAGNOSIS & TESTING
03–394Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Diagnostic Scan Tool Configuration
ITEM NAMEDESCRIPTION
1 X-431 Main Unit To Display Operational
Buttons, Test Results, Help
Information, etc.
2 Mini-Printer To Print Test Results.
(Optional)
3 CF Card To Store Diagnostic Software
and Data
4 USB Cable To Connect CF Card
Reader/Writer and Computer
5 CF Card
Reader/Writer To Read or Write Data On
The CF Card
6 Mitsubishi-12+16
Pin Connector To Diagnose Mitsubishi
Electronic Control Systems
On Chery B11 Series
7 Fiat-3 Pin
Connector To Diagnose Vehicles With
Fiat-3 Pin Diagnostic
ConnectorITEM NAME
DESCRIPTION
8 Smart OBDII-16
Pin Connector To Diagnose Other Systems
Of Vehicle With OBDII-16
Pin Diagnostic Connector
9 Power Cord To Connect AC 100 - 240 V
Outlet and Power Adapter
10 Cigarette Lighter
Cable To Get Power From Vehicle
Cigarette Lighter
11 Battery Cable
W/Two Clips To Get Power From Vehicle
Battery
12 Power Adapter To Convert 100 - 240 V AC
Power Into 12 V DC Power
13 Main Cable To Connect The Diagnostic
Connector and Smartbox
14 Smartbox To Perform Vehicle
Diagnosis
DIAGNOSIS & TESTING
BESM030003
03–460Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Lack / Loss Of Power
The following conditions apply to this symptom:
•The engine has poor performance.
• The engine has poor acceleration.
1.PRELIMINARY CHECKS
• Verify symptom is reported under normal driving conditions without excessive engine/vehicle load conditions.
• Carry out the following preliminary checks:
Fuel quality
Vacuum lines (check for damage and correct routing)
Intake air system (check for damaged tubes and dirty air filter)
Vehicle wiring (disconnected, corroded/damaged)
Throttle linkage
Radiator (obstructed)
Transaxle
NOTE :
Be aware of the over RPM limiting functions of the ECM.
Are all checks OK?
Ye s>>Go to the next step.
No
>>Repair as necessary.
Verify the symptom no longer exists.
2.CHECK ECM DTC
• Turn ignition switch on.
• With the scan tool X-431, read the DTC.
Do any DTC displayed on the scan tool?
Ye s>>See the Diagnostic Trouble Code (DTC) List.
Go to the specific diagnostic test to troubleshoot the DTC.
No
>>Go to the next step.
3.CHECK FUEL SYSTEM PRESSURE
• Release the fuel system pressure (See Fuel Pressure Relief Procedure in Section 04 Fuel Delivery).
• Check fuel system pressure (See Fuel Pressure Test in Section 04 Fuel Delivery).
Is fuel pressure correct?
Ye s>>Go to the next step.
No
>>If the fuel pressure is greater than 400 kPa (4.0 bar):
Replace the fuel pressure regulator.
If the fuel pressure is less than 400 kPa (4.0 bar):
Check the fuel supply system for restrictions or leaks.
If no problems, repair or replace fuel filter, pressure regulator or fuel pump assembly.
ELECTRONIC ENGINE CONTROLS - 2.4L ENGINE SYMPTOM DIAGNOSIS
03
03–553Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4.CHECK TFT SENSOR
• Check TFT sensor as follows:
TFT SENSOR RESISTANCE
TEMPERATURE °C RESISTANCE
-50 93917
-30 28237.4
-10 9826
0 6079
20 2528.5
25 2063
40 1159.2
50 810.4
70 419.1
80 309.2
100 176.2
120 105.9
140 66.7
Is the check result normal?
Ye s>>Go to the next step.
No
>>Replace the TFT sensor.
5.CHECK A/T FLUID PRESSURE SENSOR
• Turn ignition switch on.
• With X-431 scan tool, select view TCM data stream and compare to the following table.
ITEM CONDITION DISPLAY
VALUE
Fluid Pressure •
Ignition switch:
ON
• Engine: Not
running Below 0.2 bar
• Engine: Idle
• TFT: 31°C
• ECT: 30°C Approximately
0.05 bar
Is the check result normal?
Ye s>>Go to the next step.
No
>>Replace the TCM.
DIAGNOSIS & TESTING
08–26Chery Automobile Co., Ltd.