2009 CHERY TIGGO engine

Downloaded from www.Manualslib.com manuals search engine •Continuity should exist.
• Also check harness for short to power.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace the circuit for an open or short to power in harness or connectors.
5.CHECK FUEL PRESSURE
• Release fuel pressure to zero.
• Install fuel pressure gauge (2) and check fuel
pressure.
• Observe the following fuel pressures when testing (See Fuel Pressure Test in Section 04 Fuel Delivery)
FUEL PRESSURES
Key On 400 kPa (4 bar)
Key Off 380 kPa (3.8 bar) in 10 minutes
Engine Idle 400 kPa (4.0 bar) - 420 kPa (4.2 bar)
Is the check result normal?
Ye s>>Go to step 7.
No
>>Go to the next step.
DIAGNOSIS & TESTING
BESM030020
03
03–341Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 6.DETECT MALFUNCTIONING PART
• Check the following:
Fuel pump and circuit
Fuel pressure regulator
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace malfunctioning part.
7.CHECK MAF SENSOR
• Turn ignition switch off.
• Install all removed parts.
• Check air flow in data stream.
MAF SENSOR SIGNAL
TERMINAL NO. ITEMCONDITION DATA
37 Air flow sensor •
Engine is running
• ECT: 78°C
• Idle: 795 RPM
• IAT: 36°C
• IAT signal: 1.88 V 322 kg/h
1.39 V
Is the check result normal?
Ye s>>If with the X-431, go to the next step.
If without the X-431, go to step 9.
No
>>Check connectors for damaged or air flow signal circuit for short to power.
8.PERFORM ACTIVE TEST FUNCTION
• Start engine.
• Select ACTIVE TEST menu.
• Perform injector active test.
• Make sure that each test produces a momentary engine speed drop.
Is the check result normal?
Ye s>>Go to step 11.
No
>>Go to the next step.
9.CHECK FUNCTION OF INJECTOR
• Listen to each injector operating sound.
• Operating sound should exist.
Is the check result normal?
Ye s>>Go to step 11.
No
>>Go to the next step.
DIAGNOSIS & TESTING
03–342Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 10.CHECK INJECTOR CONTROL CIRCUIT
• Turn ignition switch off.
• Disconnect injector harness connector (1).
• Disconnect ECM harness connector.
• check harness for short to ground between following terminals.
• Continuity should not exist.
INJECTOR NO. ECM
TERMINAL INJECTOR
TERMINAL
12 72
262
372
44 72
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace the circuit for short to ground in harness or connectors.
11 .CHECK INJECTOR RESISTANCE
• Disconnect injector harness connectors (See Fuel Pressure Test in Section 04 Fuel Delivery).
• Check the fuel injector resistance as shown in the following:
INJECTOR RESISTANCE
INJECTOR NO. INJECTOR
TERMINAL RESISTANCE
(APPROXIMATELY) (20°C)
1 1&2
11-16
2
1&2
3 1&2
4 1&2
DIAGNOSIS & TESTING
BESM040006
03
03–343Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Is the check result normal?
Ye s>>Go to the next step.
No
>>Replace injector.
Go to step 14.
12.CHECK INJECTOR
WARNING!
Confirm that the engine is cooled down and there are no fire hazards near the vehicle.
• Remove fuel delivery rail with injectors (See Fuel Injector Rail Removal & Installation 1.6L/1.8L/2.0L in Section
04 Fuel Delivery).
NOTE :
Be careful not to drop the fuel injectors when removing the fuel delivery rail.
• Keep fuel hose and all injectors connected to injector rail.
• Disconnect all injector harness connectors.
• Disconnect all ignition coil harness connectors.
• Prepare pans or saucers under each injector.
• Crank engine for about 3 seconds.
• Make sure fuel does not drip from injector.
Is the check result normal?
Ye s>>Go to next step.
No
>>Replace any leaking injectors as necessary. Always replace the O-ring seal when replacing the fuel
injector .
13.CHECK DTC
• With the X-431 scan tool, read ECM DTCs.
• Refer to DTC Confirmation Procedure.
Is DTC P0172 still present?
Ye s>>Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
DIAGNOSIS & TESTING
03–344Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine P0201 - Cylinder 1 - Injector Circuit
P0202 - Cylinder 2 - Injector Circuit
P0203 - Cylinder 3 - Injector Circuit
P0204 - Cylinder 4 - Injector Circuit
DIAGNOSIS & TESTING
LTSMW030029T
03
03–345Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DIAGNOSIS & TESTING
LTSMW030030T
03–346Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Check reference values between ECM terminals and ground under the following conditions:
ECM TERMINAL NO.ITEMCONDITIONDATA (AVERAGE DC
VOLTAGE)
6 Injector 2
•Engine is running
• Warm-up condition
• Idle
• Accelerate suddenly Voltage: 11 - 14 V
7
Injector 3
27 Injector 1
47 Injector 4
On Board Diagnostic Logic
• Self-diagnosis detection logic.
DTC NO. DTC DEFINITION DTC DETECTION
CONDITION POSSIBLE CAUSE
P0201 Cylinder 1 - Injector Circuit
Engine is running•
Injector
• Harness or connectors
• ECM
P0202
Cylinder 2 - Injector Circuit
P0203 Cylinder 3 - Injector Circuit
P0204 Cylinder 4 - Injector Circuit
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
•Turn ignition switch off.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on.
• With the scan tool, record and erase stored DTCs in the ECM.
• Start engine and warm it to normal operating temperature then select view DTC.
• If DTC is detected, go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnosis & Testing Diagnostic Help in Sec-
tion 03 Electronic Engine Controls).
NOTE :
While performing electrical diagnosis & testing, always refer to the electrical schematics for specific circuit
and component information.
Diagnostic Procedure
1.CHECK GROUND CONNECTIONS
• Turn ignition switch off.
• Loosen and retighten ground screws on the body (See Ground Inspection in Section 03 Electronic Engine Con-
trols).
• Inspect ground connections E-207 and E-208 mounting position (See Vehicle Wiring Harness Layout - Engine
Room Harness (With 2.0L Engine) in Section 16 Wiring).
Are the ground connections OK?
Ye s>>Go to the next step.
No
>>Repair or replace ground harness or connections.
DIAGNOSIS & TESTING
03
03–347Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 2.INSPECTION START
• Start engine.
Is any cylinder ignited?
Ye s>>If with the X-431, go to the next step.
If without the X-431, go to step 4.
No
>>Go to step 5.
3.PERFORM ACTIVE TEST FUNCTION
• Start engine.
• Select ACTIVE TEST menu.
• Perform injector active test.
• Make sure that each test produces a momentary engine speed drop.
Is the check result normal?
Ye s>>Go to step 11.
No
>>Go to step 5.
4.CHECK FUNCTION OF INJECTORS
• Listen to injectors for operating sound one by one.
Does a clicking noise exist for all injectors?
Ye s>>Go to step 11.
No
>>Go to the next step.
5.CHECK INJECTOR ELECTRICAL CONNECTOR
• Turn ignition switch off.
• Disconnect the injector electrical connector (1).
• Inspect the electrical connector for damage.
Is the electrical connector OK?
Ye s>>Go to the next step.
No
>>Repair or replace the electrical connector
as necessary.
DIAGNOSIS & TESTING
BESM040006
03–348Chery Automobile Co., Ltd.