2009 CHERY TIGGO fuse

Downloaded from www.Manualslib.com manuals search engine Engine Cranks Normal But Will Not Start
The following conditions apply to this symptom:
•The engine cranks at normal speed.
• The engine will not start.
• The battery is fully charged.
1.PRELIMINARY CHECKS
CAUTION:
Extended cranking because of a No Start can load the exhaust system with raw fuel, damaging the
catalytic converter after the engine starts.
•Carry out the following preliminary checks:
Fuel quality
Electrical connections
Intake air tube integrity
Fuses and relays
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair as necessary.
Verify the symptom no longer exists.
2.CHECK DTC
• Turn the ignition switch on.
• With the scan tool X-431, select view DTC.
Are there any DTCs present?
Ye s>>See the Diagnostic Trouble Code (DTC) List.
Go to the specific diagnostic test to troubleshoot the DTC.
No
>>Go to the next step.
3.TRY TO START THE ENGINE WITH THE THROTTLE CLOSED
• Attempt to start the engine.
Does the engine start now with the throttle closed?
Ye s>>Verify the symptom no longer exists.
No
>>Go to the next step.
4.CHECK EXHAUST SYSTEM
• Inspect the vehicles exhaust system for restriction.
Is there a restriction in the exhaust system?
Ye s>>Repair as necessary.
No
>>Go to the next step.
ELECTRONIC ENGINE CONTROLS - 2.4L ENGINE SYMPTOM DIAGNOSIS
03
03–545Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Engine Will Not Crank
The following conditions apply to this symptom:
•The engine will not crank.
1.PRELIMINARY CHECKS
• Carry out the following preliminary vehicle inspection:
Fuel quality
Battery connections
Starter relay connections
Manual transmission clutch fully depressed
Engine immobilizer activated
Fuses/Fuse links
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair as necessary.
Verify the symptom no longer exists.
•
2.LISTEN FOR STARTER RELAY CLICKING
• Attempt to start the engine.
Is a clicking sound heard from the starter relay when the ignition key is turned to START?
Ye s>>Go to the next step.
No
>>Go to step 5.
3.CHECK STARTING SYSTEM
• Check the starter, starter ground, starter relay cable to starter and battery.
Is a fault indicated?
Ye s>>Repair as necessary.
No
>>Go to the next step.
4.CHECK OPERATION OF OTHER ELECTRICAL ACCESSORIES
• Check all accessories.
Do any other electrical accessories work?
Ye s>>Go to the next step.
No
>>Check the charging system.
ELECTRONIC ENGINE CONTROLS - 2.4L ENGINE SYMPTOM DIAGNOSIS
03
03–547Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Hard Start / Long Crank / Erratic Start / Erratic Crank
The following conditions apply to this symptom:
•The engine cranks for an extended period of time.
• The engine starts hard during a long cranking time.
1.PRELIMINARY CHECKS
• Confirm that the correct starting procedure was used by the customer before proceeding with diagnosis.
• Carry out the following preliminary checks:
Vacuum leaks
Fuel quality (concerns such as correct octane, contamination, winter/summer blend)
Intake air system (tubes)
Air cleaner (restrictions)
Battery condition and starter current draw.
Are all checks OK?
Ye s>>Go to the next step.
No
>>Repair as necessary.
Verify the symptom no longer exists.
2.CHECK ECM DTC
• With scan tool X-431, select view DTC and data stream in ECM.
Are there any DTCs present?
Ye s>>See the Diagnostic Trouble Code (DTC) List.
Go to the specific diagnostic test to troubleshoot the DTC.
No
>>Go to the next step.
3.CHECK SECONDARY IGNITION SYSTEM
• Perform the following to test the secondary ignition system:
Disconnect the injector fuse.
Remove any of the 4 spark plugs.
Connect the spark plug to spark plug wire.
Ground the spark plug on the cylinder block.
Crank the engine to test the secondary ignition system with the spark plugs removed.
Is a strong blue spark visible at each spark plug while cranking the engine?
Ye s>>Go to the next step.
No
>>Check Camshaft Position (CMP) sensor signal at ECM.
If CMP sensor is OK, check the following:
Crankshaft Position (CKP) sensor malfunction
Faulty spark plug wires
Faulty spark plugs
ELECTRONIC ENGINE CONTROLS - 2.4L ENGINE SYMPTOM DIAGNOSIS
03
03–549Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4.CHECK SECONDARY IGNITION SYSTEM
• Perform the following to test the secondary ignition system:
Disconnect the injector fuse.
Remove any of the 4 spark plugs.
Connect the spark plug to spark plug wire.
Ground the spark plug on the cylinder block.
Crank the engine to test the secondary ignition system with the spark plugs removed.
Is a strong blue spark visible at each spark plug while cranking the engine?
Ye s>>Go to the next step.
No
>>Check Camshaft Position (CMP) sensor signal at ECM.
If CMP sensor is OK, check the following:
Crankshaft Position (CKP) sensor malfunction
Spark plug wires
Spark plugs
5.CHECK INTAKE AIR SYSTEM
• Check for MAP/MAF sensor.
Is there any contamination?
Ye s>>Clean or replace the sensor.
No
>>Go to the next step.
6.CHECK EXHAUST SYSTEM
• Check the exhaust system for restrictions.
Is there a restriction in the exhaust system?
Ye s>>Repair as necessary.
No
>>Go to the next step.
7.CHECK BASE ENGINE CONCERNS
• Check for base engine concerns (such as improper compression, worn camshaft/valve train, gasket leaks).
Is a fault indicated?
Ye s>>Repair as necessary.
No
>>Go to the next step.
8.CHECK AUTOMATIC/MANUAL TRANSAXLE OPERATION
• Check the operation of the transaxle.
Is the transaxle operation normal?
Ye s>>Go to the next step.
No
>>Repair as necessary.
ELECTRONIC ENGINE CONTROLS - 2.4L ENGINE SYMPTOM DIAGNOSIS
03–554Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Back Fires
The following conditions apply to this symptom:
•The engine will back fire when operated.
• The engine back fire occurs at all operating parameters.
1.PRELIMINARY CHECKS
• Carry out the following preliminary checks:
Vacuum lines (check for damage and correct routing).
Spark plug wire routing (correct firing order).
Are all checks OK?
Ye s>>Go to the next step.
No
>>Repair as necessary.
Verify the symptom no longer exists.
2.CHECK ECM DTC
• Turn the ignition switch on.
• With the scan tool X-431, select view DTC and stream data in ECM.
Are there any DTCs present?
Ye s>>See the Diagnostic Trouble Code (DTC) List.
Go to the specific diagnostic test to troubleshoot the DTC.
No
>>Go to the next step.
3.CHECK SECONDARY IGNITION SYSTEM
• Perform the following to test the secondary ignition system:
Disconnect the injector fuse.
Remove any of the 4 spark plugs.
Connect the spark plug to spark plug wire.
Ground the spark plug on the cylinder block.
Crank the engine to test the secondary ignition system with the spark plugs removed.
Is a strong blue spark visible at each spark plug while cranking the engine?
Ye s>>Go to the next step.
No
>>Check Camshaft Position (CMP) sensor signal at ECM.
If CMP sensor is OK, check the following:
Crankshaft Position (CKP) sensor malfunction
Spark plug wires
Spark plugs
4.CHECK FUEL QUALITY
• Check fuel quality (concerns such as correct octane, contamination).
Is the fuel quality OK?
Ye s>>Go to the next step.
No
>>Repair as necessary.
Verify the symptom no longer exists.
ELECTRONIC ENGINE CONTROLS - 2.4L ENGINE SYMPTOM DIAGNOSIS
03–556Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 6.CHECK SECONDARY IGNITION SYSTEM
• Perform the following to test the secondary ignition system:
Disconnect the injector fuse.
Remove any of the 4 spark plugs.
Connect the spark plug to spark plug wire.
Ground the spark plug on the cylinder block.
Crank the engine to test the secondary ignition system with the spark plugs removed.
Is a strong blue spark visible at each spark plug while cranking the engine?
Ye s>>Go to the next step.
No
>>Check Camshaft Position (CMP) sensor signal at ECM.
If CMP sensor is OK, check the following:
Crankshaft Position (CKP) sensor malfunction
Spark plug wires
Spark plugs
7.CHECK FUEL SYSTEM PRESSURE
• Release the fuel system pressure (See Fuel Pressure Relief Procedure in Section 04 Fuel Delivery).
• Check fuel system pressure (See Fuel Pressure Test in Section 04 Fuel Delivery).
Is fuel pressure correct?
Ye s>>Go to the next step.
No
>>If the fuel pressure is greater than 400 kPa (4.0 bar):
Replace the fuel pressure regulator.
If the fuel pressure is less than 400 kPa (4.0 bar):
Check the fuel supply system for restrictions or leaks.
If no problems, repair or replace fuel filter, pressure regulator or fuel pump assembly.
8.CHECK EXHAUST SYSTEM
• Check the exhaust system for restrictions.
Is there a restriction in the exhaust system?
Ye s>>Repair as necessary.
No
>>Go to the next step.
9.CHECK PCV SYSTEM
• Check the Positive Crankcase Ventilation (PCV) system.
• Remove PCV valve and shake it.
Is PCV valve normal?
Ye s>>Go to the next step.
No
>>Replace the PCV valve.
ELECTRONIC ENGINE CONTROLS - 2.4L ENGINE SYMPTOM DIAGNOSIS
03–560Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine ON-VEHICLE SERVICE
Fuel Pressure Relief Procedure
Description
WARNING!
Fuel in the fuel system remains under high pressure, even when the engine is not running. Before servicing or
disconnecting any of the fuel lines or fuel system components, the fuel system pressure must be relieved to
prevent accidental spraying of fuel. Failure to follow these instructions may result in serious personal injury or
death.
Perform the following procedure to relieve fuel pressure from the fuel system:1. Remove the cover of the front fuse and relay box.
2. Identify and remove the fuel pump relay from the front fuse and relay box.
3. Start and run engine until it stalls.
4. Attempt to restart engine until it will no longer run.
5. Turn the ignition key to the OFF position.
Fuel Pump
Description
The fuel pump assembly contains the fuel pump motor and fuel level sensor.
Operation
The Engine Control Module (ECM) activates the fuel pump relay for several seconds after the ignition switch is
turned ON. When the relay is activated, it provides voltage to the fuel pump. When the ECM receives an engine
speed signal from the Crankshaft Position (CKP) sensor and a signal from the Immobilizer control module, the ECM
will energize the fuel pump relay.
NOTE :
• The electric fuel pump has different flow ratings based on engine requirements
• For service, the part number of the replacement fuel pump must be the equivalent of the original fuel pump
• Do not operate the fuel pump dry, this will damage the fuel pump
• Keep the fuel tank and pipeline clean, and replace the fuel filter if the fuel pump is replaced
Removal & Installation
WARNING!
Release fuel system pressure before servicing fuel system components. Service vehicles in well-ventilated areas
and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or death.
NOTE :
The following special tool is required to perform the repair procedure:
•CH-20032 - Fuel Pump Remover
1. Release the fuel system pressure (See Fuel Pressure Relief Procedure in Section 04 Fuel Delivery).
2. Disconnect the negative battery cable.
3. Remove the rear seat cushion.
04
04–15Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine GENERAL INFORMATION
Description
The starting system consists of the following components:
•Starter motor (including an integral starter solenoid)
• Battery
• Battery cables
• Ignition switch and key lock cylinder
• Wire harnesses and connections
• Starter relay and fuse
• Charge fuse
1.6L & 1.8L & 2.0L
2.4L
LTSM050007T
LTSM050006T
05–2Chery Automobile Co., Ltd.