2009 CADILLAC DTS light

Headlamps on Reminder
A warning chime will sound if the exterior lamp control
is left on in either the headlamp or parking lamp position
and the driver’s door is opened with the ignition off.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
Fully functional daytime running lamps are required
on all vehicles rst sold in Canada.
The DRL system makes the turn signal lamps come on
when the following conditions are met:
It is still daylight and the ignition is on.
The exterior lamp control is in the off position.
The transmission is not in P (Park)
(United States only).
The light sensor is covered or not detecting light.
See “Sensors” underDual Climate Control System
on page 3-40.
When DRL are on, no other exterior lamps such as the
parking lamps, taillamps, etc. will be on when the DRL
are being used. The instrument panel will not be lit
up either.When automatic lighting is on and it is dark enough
outside, the turn signal lamps turn off and normal
low-beam headlamp operation occurs.
When automatic lighting is on and it is bright enough
outside, the regular lamps go off, and the DRL takes over.
If the vehicle is started in a dark garage, the automatic
headlamp system comes on immediately. Once you
leave the garage, it will take approximately one minute
for the automatic headlamp system to change to DRL if
there is light outside. During that delay, the instrument
panel cluster may not be as bright as usual. Make sure
the instrument panel brightness knob is in the full bright
position. SeeInstrument Panel Brightness on page 3-34.
Turning on automatic lighting or the headlamps will
deactivate the DRL. If the parking lamps or the fog lamps
were turned on instead, the DRL will still deactivate.
To idle the vehicle with the DRL off at night, turn off
automatic lighting and shift the transmission into P (Park).
Placing the vehicle in P (Park) disables the DRL. The
DRL will stay off until the vehicle is shifted out of P (Park).
To drive the vehicle with the DRL off, turn off automatic
lighting and manually turn on the parking lamps or
fog lamps, if the vehicle has them.
The regular headlamp system should be turned on
when needed.
3-33

Fog Lamps
Use the fog lamps for better vision in foggy or misty
conditions.
The fog lamps button is located on the exterior lamps
control to the left of the steering column.
#(Fog Lamps):Press the exterior lamps button to
turn the fog lamps on or off. A light comes on in the
instrument panel cluster when the fog lamps are in use.
The ignition must be on for the fog lamps to work.
When the headlamps are changed to high-beam,
the fog lamps will turn off. The fog lamps come back on
again when the high-beam headlamps are turned off.
Some localities have laws that require the headlamps to
be on along with the fog lamps.
Cornering Lamps
The cornering lamps come on when the headlamps
or parking lamps are on and you signal a turn with the
multifunction lever. They provide more light for cornering.
Exterior Lighting Battery Saver
If the exterior lamp button has been left on, the exterior
lamps will turn off about 10 minutes after the ignition is
turned to LOCK/OFF and a door has been opened. This
protects against draining the battery if the headlamps
or parking lamps are accidentally left on. If you need to
leave the lamps on for more than 10 minutes, use the
exterior lamp control to turn the lamps back on after the
ignition is turned to LOCK/OFF and any door is opened.
Instrument Panel Brightness
D(Instrument Panel Brightness):This feature
controls the brightness of the instrument panel and
footwell lights, if equipped.
The button for this control is located below the exterior
lamps control.
Push the button in and release to extend the button.
Turn the button clockwise or counterclockwise to
brighten or dim the lights.
3-34

Courtesy Lamps
The courtesy lamps are located on the headliner above
the rear seat. These lamps come on by turning the
instrument panel brightness knob fully clockwise or when
any door is opened and it is dark outside. Puddle lamps
are located on the bottom of the front and rear door trim.
Professional vehicles have an additional dome lamp
and also opera lamps.
Entry Lighting
This feature turns on the courtesy lamps and the
backlighting for the door switches and the exterior lamp
control when a door is opened or if the remote keyless
entry transmitter unlock button is pressed. If activated
due to the transmitter, the lighting remains active for
about 40 seconds. Since the entry lighting system
uses the light sensor, it must be dark outside in order
for the courtesy lamps to turn on. The courtesy lamps
turn off approximately 25 seconds after the last door is
closed. They will dim to off if the ignition key is turned to
ON/RUN, or immediately deactivate if the power locks
are activated.
Parade Dimming
This feature prohibits dimming of the digital displays and
backlighting during daylight hours when the key is in
the ignition and the headlamps are on. This feature is
fully automatic. When the light sensor reads darkness
outside and the parking lamps are active, the digital
displays can be adjusted by turning the instrument panel
brightness knob counterclockwise to dim and clockwise
to brighten lighting.
Reading Lamps
The reading lamps are located on the overhead console
on the headliner and in the rear door opening. These
lamps come on automatically when any door is opened
and it is dark outside.
For manual operation, press the button to turn them on.
Press it again to turn them off.
If the reading lamps are left on, they automatically shut
off 10 minutes after the ignition has been turned off.
3-35

Footwell Lamps
For vehicles with footwell lamps, they are located
under the instrument panel and at the rear of the
front seats. These lamps provide soft light to the front
and rear oor areas. They dim with the instrument
panel cluster lights.
Footwell lighting brightness can be adjusted with the
instrument panel brightness control located below the
exterior lamps control. SeeInstrument Panel Brightness
on page 3-34. The footwell lights will turn off before
the instrument panel lights are at their lowest level of
brightness.
Battery Load Management
This feature monitors the vehicle’s electrical load and
determines when the battery is in a heavy discharge
condition. During times of high electrical loading, the
engine may idle at a higher revolutions per minute (rpm)
setting than normal to make sure the battery charges.
High electrical loads may occur when several of the
following are on: headlamps, high beams, fog lamps,
rear window defogger, the climate control fan at high
speeds, heated seats and engine cooling fans.If the battery continues to discharge, even with the
engine idling at a higher rpm setting, some electrical
loads will automatically be reduced. When this occurs,
the rear window defogger may take slightly longer
to clear the glass, the heated seats may not get as
warm as they usually do and the climate control fan
may cut back to a lower speed. For more battery
saving information, see “Battery Saver Active Message”
underDIC Warnings and Messages on page 3-73.
Electric Power Management
The vehicle has Electric Power Management (EPM) that
estimates the battery’s temperature and state of charge.
It then adjusts the voltage for best performance and
extended life of the battery.
When the battery’s state of charge is low, the voltage
is raised slightly to quickly bring the charge back up.
When the state of charge is high, the voltage is lowered
slightly to prevent overcharging. If the vehicle has a
voltmeter gage or a voltage display on the Driver
Information Center (DIC), you may see the voltage
move up or down. This is normal. If there is a problem,
an alert will be displayed.
3-36

Automatic Operation
AUTO9(Automatic Fan):When this position is
selected on the fan control, the system adjusts the
fan speed. If the OnStar
®system is activated when
this position is selected, the climate control fan speed
will lower.
AUTO (Automatic Mode):
1. Turn the fan control to the AUTO position.
2. Turn the mode control to the AUTO position.
3. Adjust the temperature to a comfortable setting
between 68°F (21°C) and 78°F (26°C).
Choosing the coldest or warmest temperature
setting will not cause the system to heat or cool
any faster. In cold weather, the system will start at
reduced fan speeds to avoid blowing cold air into
the vehicle until warmer air is available. The system
starts out blowing air at the oor but may change
modes automatically as the vehicle warms up to
maintain the chosen temperature setting. The length
of time needed to warm the interior depends on the
outside temperature and temperature of the vehicle.
4. Wait 20 to 30 minutes for the system to stabilize
in order for the system to regulate automatically.
Then adjust the temperature as necessary to
nd your comfort setting.Do not cover the solar sensor located in the center of
the instrument panel near the windshield. For more
information on the solar sensor, see “Sensors” later
in this section.
After the vehicle is started, the display shows the
interior temperature settings and the outside
temperature.
If the AUTO position is selected on the fan or mode
control, the system automatically controls the air
conditioning compressor. The A/C compressor will
run automatically even at cool outside temperatures
in order to dehumidify the air. The A/C indicator light
is lit when the system is operating automatically, even
at near freezing outside temperatures. Press
#on the
fan control to turn off the A/C. For improved window
clearing performance in defog or defrost modes, the
A/C compressor runs automatically.
h(AUTO RECIRCULATION):If the AUTO position is
selected on either the fan or mode control, the system
automatically controls the air inlet to supply fresh outside
air or recirculate the interior air to cool the car faster.
The light on the recirculation button will come on when
the system changes to recirculation. Outside air can be
forced by pressing
hwhen the light is lit. For vehicles
without rear climate controls, press
:to force outside
air. The next time AUTO fan or mode is selected, the air
inlet will reset back to AUTO operation.
3-41

Manual Operation
9(Off):Turns the entire climate control system off.
Outside air still enters the vehicle and is directed to
the oor. The airow direction and temperature can
be adjusted, as indicated below.
If the temperature is adjusted while the system is off,
the display will light to show the current settings.
wx(Driver’s Temperature Controls):Press the
up or down buttons next to the fan control to manually
increase or decrease the temperature inside the vehicle.
wx(Passenger’s Temperature Controls):
Press the up or down buttons next to the air delivery
mode control to manually increase or decrease the
temperature for the front passenger. If the passenger
climate control system is off, pressing one of these
buttons turns it on.
9(Fan Control):Turn clockwise or counterclockwise
to increase or decrease the fan speed. Turning this
control completely counterclockwise will turn on the
automatic fan operation. If the airow seems low
when the fan speed is at the highest setting, the
passenger compartment air lter may need to be
replaced. SeePassenger Compartment Air Filter
on page 3-48.Air Delivery Mode Control:Turn clockwise or
counterclockwise to change the current airow mode.
Select one of the following:
AUTO:Turns on the automatic delivery mode operation.
F(Vent):Air is directed to the instrument panel
outlets.
*(Bi-Level):Air is divided between the instrument
panel and the oor outlets. In automatic operation,
cooler air is directed to the upper outlets and warmer
air to the oor outlets.
7(Floor):Air is directed to the oor outlets with some
air directed to the side window outlets and the windshield.
If recirculation is selected, it only stays on for
three minutes to reduce windshield fogging.
W(Floor/Defog):This mode clears the windows of fog
or moisture. Air is directed to the oor outlets, with some
air going to the side window outlets and windshield.
When selected, the system turns off recirculation and
runs the air conditioning compressor unless the outside
temperature is at or below freezing. The recirculation
mode cannot be selected while in the oor/defog mode.
3-42

0(Defrost):This mode clears the windshield of
fog or frost more quickly. Air is directed to the windshield
and side window outlets. When selected, the system
automatically turns off recirculation and runs the air
conditioning compressor, unless the outside temperature
is at or below freezing. Recirculation cannot be selected
while in the defrost mode. Do not drive the vehicle until
all the windows are clear.
For professional vehicles, air will be allowed to ow
through the rear outlets. For quicker defrost, press the
AUX button on the front climate control system so that
the light is not lit.
#(Air Conditioning):Press to turn the air
conditioning system on or off and override the automatic
system. When in AUTO, the air conditioning compressor
comes on automatically, as necessary. To avoid window
fogging on rainy and humid days at temperatures above
freezing, run the air conditioning.
The air conditioning system removes moisture from the
air, so a small amount of water may drip under the vehicle
while idling or after turning off the engine. This is normal.
:(Outside Air):Press to turn the outside air mode
on or off. An indicator light comes on to show it is on.
Air is pulled from outside the vehicle. Pressing
?will
cancel this mode.
?(Recirculation):Press to turn the recirculation
mode on or off. An indicator light below the button
comes on to show that this mode is on. This mode
recirculates and helps to quickly cool the air inside the
vehicle. It can be used to prevent outside air and odors
from entering the vehicle. This mode cannot be selected
while in the defog or defrost modes. If you try to select the
recirculation mode, the indicator light ashes three times
and turns off.
Operation in this mode during periods of high humidity
and cool outside temperatures may result in increased
window fogging. If window fogging is experienced, select
the defrost mode.
AUX:For vehicles with a rear climate control system,
press to turn the rear climate control fan on for automatic
operation. After the AUX button is pressed, the indicator
light comes on. Press the button again to turn the
auxiliary fan off. SeeRear Climate Control System
on page 3-46.
PASS (Passenger Climate Control):Press to turn the
passenger climate control systems on or off. When the
passenger climate control system is on, the passenger
temperature setting is displayed. The temperature
selected by the front passenger also controls the rear
system air temperature unless the rear seat passengers
select their own comfort setting.
If the PASS button is pressed to turn the passenger
temperature setting off, the driver’s temperature knob
will control the temperature for the entire vehicle.
3-43

AUX (Auxiliary):Press the AUX button located on
the front climate control panel to turn the rear climate
control system on or off. When turned on the rear system
operates in automatic mode and the temperature settings
selected for the front climate control panel will also be
selected for the rear passengers.
To adjust the rear climate control system, the rear
passenger can select a different temperature, mode
or fan speed. Whenever the rear passengers have
adjusted settings on the rear climate control system,
the AUX light is lit on the front climate control system.
When the front climate control system is turned off
or in defrost mode, the rear climate control system is
turned off. The rear system will turn back on once
another front mode is selected.
For more information on how to use the front climate
control system, seeDual Climate Control System
on page 3-40. For more information on the air outlets,
seeOutlet Adjustment on page 3-46.Automatic Operation
«A ª(Fan Control):Press until AUTO appears on
the display to place the system in automatic mode. When
automatic operation is active, the system automatically
controls the fan speed. If in auto fan mode, pressing the
up arrow button will cancel automatic operation and
places the system in manual mode. If in auto mode,
pressing the down arrow will turn the rear climate
control system off.
«Nª(Air Delivery Mode Control):Press until
AUTO appears on the display to place the system
in automatic mode. When automatic operation is
active, the system controls the air delivery mode.
3-47