2009 CADILLAC CTS brake

Vehicle Symbol Chart
Here are some additional symbols that may be found on
the vehicle and what they mean. For more information
on the symbol, refer to the index.
9:Airbag Readiness Light
#:Air Conditioning
!:Antilock Brake System (ABS)
g:Audio Steering Wheel Controls or OnStar®
$:Brake System Warning Light
":Charging System
I:Cruise Control
B:Engine Coolant Temperature
O:Exterior Lamps
#:Fog Lamps
.:Fuel Gage
+:Fuses
i:Headlamp High/Low-Beam Changer
j:LATCH System Child Restraints
*:Malfunction Indicator Lamp
::Oil Pressure
}:Power
/:Remote Vehicle Start
>:Safety Belt Reminders
7:Tire Pressure Monitor
F:Traction Control
M:Windshield Washer Fluid
v

Memory Seat, Mirrors and
Steering Wheel
On vehicles with the memory package the controls are
located on the driver door. This feature is used to
program and recall memory settings for the driver seat,
outside mirror, and the steering wheel position if the
vehicle has the power tilt wheel and telescopic steering
feature.
1:Saves the seating position for driver 1.
2:Saves the seating position for driver 2.
S:Recalls the easy exit position.To save your positions in memory:
1. Adjust the driver seat, seatback recliner and
lumbar, both outside mirrors, and the steering wheel
to a comfortable position.
2. Press and hold button 1 until two beeps sound
through the driver side front speaker to let you
know that the position has been stored.
3. Repeat the procedure for a second driver using
button 2.
To recall memory positions, the vehicle must be in
P (Park) for an automatic transmission or the parking
brake applied for a manual transmission. Press and
release either button 1 or button 2. A single beep will
sound. The seat, outside mirrors, and steering wheel
will move to the position previously stored for the
identied driver.
If the Remote Keyless Entry (RKE) transmitter is
used to enter the vehicle and the remote recall
memory feature is on, automatic seat and mirror
movement occur.
1-8

On vehicles with the Keyless Access System, automatic
adjustment occurs when the driver door is opened.
See “MEMORY SEAT RECALL” underDIC Vehicle
Customization on page 3-72for more information.
To stop recall movement of the memory feature at any
time, press one of the power seat controls, memory
buttons, power tilt wheel control, or power mirror
buttons.
If something has blocked the driver seat or the steering
column while recalling a memory position, the recall
may stop. Remove the obstruction, then press the
appropriate control for the area that is not recalling for
two seconds. Try recalling the memory position again by
pressing the appropriate memory button. If the memory
position is still not recalling, see your dealer/retailer
for service.Easy Exit Recall
S
:With the vehicle in P (Park) for an automatic
transmission or the parking brake applied for a manual
transmission, press the exit button to recall the exit
position.
If the easy exit seat feature is on in the DIC, automatic
seat and power telescopic steering column movement
occurs when the key is removed from the ignition.
On vehicles with the Keyless Access System, automatic
adjustment occurs when the ignition is turned to OFF
and the driver door is opened.
A single beep sounds. The driver seat moves back, and
if the vehicle has the power tilt wheel and telescopic
steering feature, it moves up and forward.
See “EASY EXIT RECALL” underDIC Vehicle
Customization on page 3-72for more information.
For more programming information, seeDIC Vehicle
Customization on page 3-72.
1-9

Keys...............................................................2-3
Remote Keyless Entry (RKE) System................2-5
Remote Keyless Entry (RKE) System
Operation...................................................2-6
Keyless Access System...................................2-8
Keyless Access System Operation....................2-8
Remote Vehicle Start....................................2-14
Doors and Locks............................................2-16
Door Locks..................................................2-16
Central Door Unlocking System......................2-16
Power Door Locks........................................2-17
Delayed Locking...........................................2-17
Programmable Automatic Door Locks..............2-17
Rear Door Security Locks..............................2-18
Lockout Protection........................................2-19
Trunk..........................................................2-19
Windows........................................................2-22
Power Windows............................................2-23
Sun Visors...................................................2-25
Theft-Deterrent Systems..................................2-26
Theft-Deterrent System..................................2-26
Immobilizer..................................................2-27
Immobilizer Operation (Key Access)................2-28
Immobilizer Operation (Keyless Access)...........2-29Starting and Operating Your Vehicle................2-30
New Vehicle Break-In....................................2-30
Ignition Positions (Key Access).......................2-31
Ignition Positions (Keyless Access)..................2-32
Retained Accessory Power (RAP)...................2-33
Starting the Engine.......................................2-33
Engine Coolant Heater..................................2-35
Automatic Transmission Operation...................2-36
Manual Transmission Operation......................2-40
Parking Brake..............................................2-42
Electric Parking Brake
...................................2-44
Shifting Into Park (Automatic Transmission)......2-47
Shifting Out of Park......................................2-48
Parking the Vehicle (Manual Transmission).......2-49
Parking Over Things That Burn.......................2-49
Engine Exhaust............................................2-50
Running the Vehicle While Parked..................2-51
Mirrors...........................................................2-52
Automatic Dimming Rearview Mirror................2-52
Outside Power Mirrors...................................2-52
Park Tilt Mirrors............................................2-53
Outside Convex Mirror...................................2-53
Outside Heated Mirrors..................................2-53
Section 2 Features and Controls
2-1

Remote Keyless Entry (RKE)
System Operation
The Remote Keyless Entry (RKE) transmitter functions
work up to 65 feet (20 m) away from the vehicle.
There are other conditions that can affect the
performance of the transmitter. SeeRemote Keyless
Entry (RKE) System on page 2-5.
Q(Lock):Press to lock all
the doors.
If enabled through the Driver
Information Center (DIC),
the parking lamps may ash
once to indicate locking has
occurred. The horn may
chirp when
Qis pressed
again within ve seconds.
SeeDIC Vehicle
Customization on page 3-72
for additional information.
K(Unlock):Press to unlock the driver door. IfKis
pressed again within ve seconds, all remaining doors
unlock. The interior lamps come on and stay on for
20 seconds or until the ignition is turned on.If enabled through the DIC, the parking lamps ash
twice to indicate unlocking has occurred. SeeDIC
Vehicle Customization on page 3-72.
V(Remote Trunk Release):Press and hold for
about one second to unlock the trunk. The automatic
transmission must be in P (Park) or the manual
transmission must be in Neutral with the parking
brake set.
L(Vehicle Locator/Panic Alarm):Press and release
to locate the vehicle. The turn signal lamps ash and
the horn sounds three times.
Press and hold
Lfor more than two seconds to activate
the panic alarm. The turn signal lamps ash and the horn
sounds for 30 seconds. The alarm turns off when the
ignition is moved to START or
Lis pressed again.
The ignition must be in LOCK/OFF for the panic alarm
to work.
The vehicle comes with two transmitters. Each
transmitter will have a number on top of it, “1” or “2”.
These numbers correspond to the driver of the vehicle.
For example, the memory seat position for driver 1 will be
recalled when using the transmitter labeled “1”, if enabled
through the DIC. SeeMemory Seat, Mirrors and Steering
Wheel on page 1-8andDIC Vehicle Customization
onpage 3-72.
2-6

For vehicles with the memory feature, pressKon the
keyless access transmitter to program and recall the
memory settings. SeeMemory Seat, Mirrors and Steering
Wheel on page 1-8for more information.
/(Remote Start):Press to operate the remote start
feature. SeeRemote Vehicle Start on page 2-14
for additional information.
G(Trunk):Press and hold for about one second to
unlock the trunk. If the engine is running, the shift lever
must be in P (Park) for an automatic transmission or in
Neutral with the parking brake set for a manual
transmission.
L(Vehicle Locator/Panic Alarm):Press and release
to locate the vehicle. The horn sounds three times
and the turn signal lamps ash three times.
Press and hold
Lfor three seconds to sound the panic
alarm. The horn sounds and the turn signal lamps ash
for 30 seconds. Press and release
Lagain to stop the
alarm.
The vehicle comes with two transmitters. Each
transmitter will have a number on top of it, “1” or “2”.
These numbers correspond to the driver of the vehicle.
For example, the memory seat position for driver 1 will be
recalled when using the transmitter labeled “1”, if enabled
through the DIC. SeeMemory Seat, Mirrors and Steering
Wheel on page 1-8andDIC Vehicle Customization
onpage 3-72.
Programming Transmitters to the
Vehicle
Only keyless access transmitters programmed to the
vehicle will work. If a transmitter is lost or stolen,
a replacement can be purchased and programmed
through your dealer/retailer. The vehicle can be
reprogrammed so that lost or stolen transmitters no
longer work. Each vehicle can have up to four
transmitters matched to it.
Programming with a Recognized
Transmitter
A new transmitter can be programmed to the vehicle
when there is one recognized transmitter. For vehicles
sold in Canada, two recognized transmitters are required
to program a new transmitter.
1. The vehicle must be off.
2. Both the recognized and new transmitters must be
with you.
3. Insert the vehicle key into the key lock cylinder
located on the outside of the driver door.
2-10

Starting the Vehicle with a Low
Transmitter Battery
Replace the battery if the Replace Battery In Remote
Key message displays in the DIC. See “Replace Battery
In Remote Key” underDIC Warnings and Messages
on page 3-58for additional information.
If the transmitter battery is weak, the DIC may display
Electronic Key Not Detected when you try to start the
vehicle. To start the vehicle, place the transmitter in the
center console storage area transmitter pocket with the
buttons facing to the front of the vehicle. Then, with the
vehicle in P (Park) or N (Neutral), press the brake pedal
and the ignition control knob. SeeStarting the Engine on
page 2-33, for additional information about the vehicle’s
electronic keyless ignition with push start. Replace the
transmitter battery as soon as possible.
Battery Replacement
Notice:When replacing the battery, do not touch
any of the circuitry on the transmitter. Static
from your body could damage the transmitter.
1. Separate the transmitter with a at, thin object
inserted into the slot on the side or back of the
transmitter.
2. Remove the old battery. Do not use a metal object.
3. Insert the new battery, positive side facing down.
Replace with a CR2032 or equivalent battery.
4. Snap the transmitter back together.
2-13

Remote Vehicle Start
This vehicle may have a remote starting feature that
allows you to start the engine from outside the vehicle.
It may also start the vehicle’s automatic climate control
system. When the remote start system is active, the
climate control system heats and cools the inside of the
vehicle according to the previous settings of the system
before turning the vehicle off. The windshield defroster
and/or rear window defogger turn on if it is cold outside.
If the vehicle has heated seats, they also turn on if the
interior or exterior temperature is cold enough. See
Heated and Ventilated Seats on page 1-7for additional
information. Normal operation of the climate control
system returns after the ignition is turned to ON/RUN.
SeeDual Climate Control System on page 3-24.
/(Remote Start):This button will be on the
transmitter if the vehicle has remote start.
To start the vehicle using the remote start feature:
1. Aim the transmitter at the vehicle.
2. Press and release the transmitter’s
Q, then
immediately press and hold the transmitter’s
/for at
least four seconds or until the vehicle’s turn signal
lamps ash. The vehicle’s doors will be locked.
When the vehicle starts, the parking lamps turn on
and remain on while the vehicle is running.3. If it is the rst remote start since the vehicle has been
driven, repeat these steps, while the engine is still
running, to extend the engine running time by
10 minutes. Remote start can be extended one time.
If the vehicle is left running it automatically shuts off after
10 minutes unless a time extension has been done.
To manually shut off a remote start:
Aim the transmitter at the vehicle and press the
remote start button until the parking lamps turn off.
Turn on the hazard warning ashers.
Turn the ignition switch on and then off.
When you enter the vehicle during a remote start, press
the brake pedal and turn the ignition to ON/RUN to drive
the vehicle.
Laws in some communities may restrict the use of
remote starters. For example, some laws may require
a person using remote start to have the vehicle in
view when doing so. Check local regulations for any
requirements on remote starting of vehicles.
Do not use the remote start feature if the vehicle is low
on fuel. The vehicle may run out of fuel.
2-14