2009 CADILLAC CTS turn signal

Remote Keyless Entry (RKE)
System Operation
The Remote Keyless Entry (RKE) transmitter functions
work up to 65 feet (20 m) away from the vehicle.
There are other conditions that can affect the
performance of the transmitter. SeeRemote Keyless
Entry (RKE) System on page 2-5.
Q(Lock):Press to lock all
the doors.
If enabled through the Driver
Information Center (DIC),
the parking lamps may ash
once to indicate locking has
occurred. The horn may
chirp when
Qis pressed
again within ve seconds.
SeeDIC Vehicle
Customization on page 3-72
for additional information.
K(Unlock):Press to unlock the driver door. IfKis
pressed again within ve seconds, all remaining doors
unlock. The interior lamps come on and stay on for
20 seconds or until the ignition is turned on.If enabled through the DIC, the parking lamps ash
twice to indicate unlocking has occurred. SeeDIC
Vehicle Customization on page 3-72.
V(Remote Trunk Release):Press and hold for
about one second to unlock the trunk. The automatic
transmission must be in P (Park) or the manual
transmission must be in Neutral with the parking
brake set.
L(Vehicle Locator/Panic Alarm):Press and release
to locate the vehicle. The turn signal lamps ash and
the horn sounds three times.
Press and hold
Lfor more than two seconds to activate
the panic alarm. The turn signal lamps ash and the horn
sounds for 30 seconds. The alarm turns off when the
ignition is moved to START or
Lis pressed again.
The ignition must be in LOCK/OFF for the panic alarm
to work.
The vehicle comes with two transmitters. Each
transmitter will have a number on top of it, “1” or “2”.
These numbers correspond to the driver of the vehicle.
For example, the memory seat position for driver 1 will be
recalled when using the transmitter labeled “1”, if enabled
through the DIC. SeeMemory Seat, Mirrors and Steering
Wheel on page 1-8andDIC Vehicle Customization
onpage 3-72.
2-6

Keyless Unlocking
With the keyless access transmitter in range, approach
the front door to unlock it and pull the handle to open
the door. All doors will unlock when you approach the
vehicle with the keyless access transmitter and open the
driver’s door.
With the keyless access transmitter in range, pull the
rear door handle once to unlock the door and a second
time to open the door.
To customize which doors unlock when the driver’s door
handle is pulled, see “Keyless Unlock” underDIC Vehicle
Customization on page 3-72.
Keyless Locking
The doors lock after several seconds if all doors are
closed and at least one keyless access transmitter
has been removed from the interior of the vehicle.
To customize whether the doors automatically lock
when you exit the vehicle, see “Keyless Locking”
underDIC Vehicle Customization on page 3-72.
Keyless Trunk Opening
Press the trunk release button located on the trunk
lid above the license plate to open the trunk if the
keyless access transmitter is within range.
There are other conditions which can affect the
performance of the transmitter. SeeKeyless Access
System on page 2-8.
Q(Lock):Press once to
lock the doors. The turn
signal indicators ash.
When
Qis pressed twice,
the turn signal indicators
ash twice, and the
horn sounds once
to conrm locking.
To program the vehicle so the turn signal indicators
do not ash and the horn does not sound when pressing
Qon the keyless access transmitter, see “Remote Door
Lock” underDIC Vehicle Customization on page 3-72.
K(Unlock):Press once to unlock only the driver door.
The turn signal indicators ash twice.
Press
Ktwice within ve seconds to unlock all the
doors. The interior lamps may come on.
To program the vehicle so the turn signal indicators do
not ash and the fog lamps and reverse lamps remain on
steady for about 20 seconds when the keyless access
transmitter is used to unlock the vehicle, see″Remote
Door Unlock″underDIC Vehicle Customization on
page 3-72. With Remote Start
Shown, Without Similar
2-9

For vehicles with the memory feature, pressKon the
keyless access transmitter to program and recall the
memory settings. SeeMemory Seat, Mirrors and Steering
Wheel on page 1-8for more information.
/(Remote Start):Press to operate the remote start
feature. SeeRemote Vehicle Start on page 2-14
for additional information.
G(Trunk):Press and hold for about one second to
unlock the trunk. If the engine is running, the shift lever
must be in P (Park) for an automatic transmission or in
Neutral with the parking brake set for a manual
transmission.
L(Vehicle Locator/Panic Alarm):Press and release
to locate the vehicle. The horn sounds three times
and the turn signal lamps ash three times.
Press and hold
Lfor three seconds to sound the panic
alarm. The horn sounds and the turn signal lamps ash
for 30 seconds. Press and release
Lagain to stop the
alarm.
The vehicle comes with two transmitters. Each
transmitter will have a number on top of it, “1” or “2”.
These numbers correspond to the driver of the vehicle.
For example, the memory seat position for driver 1 will be
recalled when using the transmitter labeled “1”, if enabled
through the DIC. SeeMemory Seat, Mirrors and Steering
Wheel on page 1-8andDIC Vehicle Customization
onpage 3-72.
Programming Transmitters to the
Vehicle
Only keyless access transmitters programmed to the
vehicle will work. If a transmitter is lost or stolen,
a replacement can be purchased and programmed
through your dealer/retailer. The vehicle can be
reprogrammed so that lost or stolen transmitters no
longer work. Each vehicle can have up to four
transmitters matched to it.
Programming with a Recognized
Transmitter
A new transmitter can be programmed to the vehicle
when there is one recognized transmitter. For vehicles
sold in Canada, two recognized transmitters are required
to program a new transmitter.
1. The vehicle must be off.
2. Both the recognized and new transmitters must be
with you.
3. Insert the vehicle key into the key lock cylinder
located on the outside of the driver door.
2-10

Remote Vehicle Start
This vehicle may have a remote starting feature that
allows you to start the engine from outside the vehicle.
It may also start the vehicle’s automatic climate control
system. When the remote start system is active, the
climate control system heats and cools the inside of the
vehicle according to the previous settings of the system
before turning the vehicle off. The windshield defroster
and/or rear window defogger turn on if it is cold outside.
If the vehicle has heated seats, they also turn on if the
interior or exterior temperature is cold enough. See
Heated and Ventilated Seats on page 1-7for additional
information. Normal operation of the climate control
system returns after the ignition is turned to ON/RUN.
SeeDual Climate Control System on page 3-24.
/(Remote Start):This button will be on the
transmitter if the vehicle has remote start.
To start the vehicle using the remote start feature:
1. Aim the transmitter at the vehicle.
2. Press and release the transmitter’s
Q, then
immediately press and hold the transmitter’s
/for at
least four seconds or until the vehicle’s turn signal
lamps ash. The vehicle’s doors will be locked.
When the vehicle starts, the parking lamps turn on
and remain on while the vehicle is running.3. If it is the rst remote start since the vehicle has been
driven, repeat these steps, while the engine is still
running, to extend the engine running time by
10 minutes. Remote start can be extended one time.
If the vehicle is left running it automatically shuts off after
10 minutes unless a time extension has been done.
To manually shut off a remote start:
Aim the transmitter at the vehicle and press the
remote start button until the parking lamps turn off.
Turn on the hazard warning ashers.
Turn the ignition switch on and then off.
When you enter the vehicle during a remote start, press
the brake pedal and turn the ignition to ON/RUN to drive
the vehicle.
Laws in some communities may restrict the use of
remote starters. For example, some laws may require
a person using remote start to have the vehicle in
view when doing so. Check local regulations for any
requirements on remote starting of vehicles.
Do not use the remote start feature if the vehicle is low
on fuel. The vehicle may run out of fuel.
2-14

When the System Does Not Seem to
Work Properly
If the URPA system will not activate due to a temporary
condition, the message PARK ASSIST OFF will be
displayed on the DIC and a red light will be shown on
the rear URPA display when the shift lever is moved into
R (Reverse). This occurs under the following conditions:
The driver disables the system.
The ultrasonic sensors are not clean. Keep the
vehicle’s rear bumper free of mud, dirt, snow,
ice and slush. For cleaning instructions, see
Washing Your Vehicle on page 5-110.
A trailer was attached to the vehicle, or a bicycle or
an object was hanging out of the trunk during the
last drive cycle, the red light may illuminate in
the rear display. Once the attached object is
removed, URPA will return to normal operation.
A tow bar is attached to the vehicle.
The vehicle’s bumper is damaged. Take the vehicle
to your dealer/retailer to repair the system.
Other conditions may affect system performance,
such as vibrations from a jackhammer or the
compression of air brakes on a very large truck.
If the system is still disabled after driving forward at least
15 mph (25 km/h), take the vehicle to your dealer/retailer.
OnStar®System
OnStar uses several innovative technologies and live
advisors to provide a wide range of safety, security,
information, and convenience services. If the airbags
deploy, the system is designed to make an automatic
call to OnStar Emergency advisors who can request
emergency services be sent to your location. If the keys
are locked in the vehicle, call OnStar at 1-888-4-ONSTAR
to have a signal sent to unlock the doors. OnStar
Hands-Free Calling, including 30 trial minutes good
for 60 days, is available on most vehicles. OnStar
Turn-by-Turn Navigation service, with one trial route, is
available on most vehicles. Press the OnStar button to
have an OnStar advisor contact Roadside Service.
OnStar service is provided subject to the OnStar Terms
and Conditions included in the OnStar Subscriber glove
box literature.
2-56

3. At the same time, press and hold both the Universal
Home Remote button to be used to control the
garage door and the hand-held transmitter button.
Do not release the Universal Home Remote button or
the hand-held transmitter button until Step 4 has
been completed.
Some entry gates and garage door openers may
require substitution of Step 3 with the procedure
noted in “Gate Operator and Canadian
Programming” later in this section.
4. The indicator light on the Universal Home Remote
will ash slowly at rst and then rapidly after
Universal Home Remote successfully receives the
frequency signal from the hand-held transmitter.
Release both buttons.
5. Press and hold the newly-trained Universal Home
Remote button and observe the indicator light.
If the indicator light stays on continuously, the
programming is complete and the garage door
should move when the Universal Home Remote
button is pressed and released. There is no need to
continue programming Steps 6 through 8.If the Universal Home Remote indicator light
blinks rapidly for two seconds and then turns
to a constant light, continue with the programming
Steps 6 through 8.
It may be helpful to have another person assist with
the remaining steps.
6. After Steps 1 through 5 have been completed,
locate inside the garage the garage door opener
receiver (motor-head unit). Locate the “Learn”
or “Smart” button. The name and color of the button
may vary by manufacturer.
2-62

7. Firmly press and release the “Learn” or “Smart”
button. After you press this button, you will have
30 seconds to complete Step 8.
8. Immediately return to the vehicle. Firmly press and
hold the Universal Home Remote button, chosen in
Step 3 to control the garage door, for two seconds,
and then release it. If the garage door does not
move, press and hold the same button a second time
for two seconds, and then release it. Again, if the
door does not move, press and hold the same button
a third time for two seconds, and then release.
The Universal Home Remote should now activate
the garage door.
To program the remaining two Universal Home Remote
buttons, begin with Step 2 of “Programming the Universal
Home Remote System.” Do not repeat Step 1, as this will
erase all previous programming from the Universal Home
Remote buttons.Gate Operator and Canadian
Programming
If you have questions or need help programming the
Universal Home Remote System, call 1-800-355-3515
or go to www.homelink.com.
Canadian radio-frequency laws require transmitter
signals to time out or quit after several seconds of
transmission. This may not be long enough for Universal
Home Remote to pick up the signal during programming.
Similarly, some U.S. gate operators are manufactured
to time out in the same manner.
If you live in Canada, or you are having difficulty
programming a gate operator or garage door opener by
using the “Programming Universal Home Remote”
procedures, regardless of where you live, replace
Step 3 under “Programming Universal Home Remote”
with the following:
Continue to press and hold the Universal Home Remote
button while you press and release every two seconds
(cycle) the hand-held transmitter button until the
frequency signal has been successfully accepted by the
Universal Home Remote. The Universal Home Remote
indicator light will ash slowly at rst and then rapidly.
Proceed with Step 4 under “Programming Universal
Home Remote” to complete.
2-63

Instrument Panel Overview...............................3-4
Hazard Warning Flashers................................3-6
Horn .............................................................3-6
Tilt and Telescopic Steering Wheel...................3-6
Power Tilt Wheel and Telescopic Steering
Column......................................................3-7
Turn Signal/Multifunction Lever.........................3-7
Turn and Lane-Change Signals........................3-8
Headlamp High/Low-Beam Changer..................3-8
Flash-to-Pass.................................................3-9
Windshield Wipers..........................................3-9
Rainsense™ Wipers......................................3-10
Windshield Washer.......................................3-12
Headlamp Washer........................................3-13
Cruise Control..............................................3-14
Headlamps..................................................3-17
Wiper Activated Headlamps............................3-17
Headlamps on Reminder................................3-17
Daytime Running Lamps (DRL).......................3-18
Adaptive Forward Lighting System...................3-19
Fog Lamps ..................................................3-19
Exterior Lighting Battery Saver........................3-20
Instrument Panel Brightness...........................3-20
Entry Lighting...............................................3-20
Parade Dimming...........................................3-20
Reading Lamps............................................3-21
Electric Power Management...........................3-21Battery Run-Down Protection..........................3-22
Accessory Power Outlet(s).............................3-22
Ashtray(s) and Cigarette Lighter......................3-23
Analog Clock...............................................3-23
Climate Controls............................................3-24
Dual Climate Control System..........................3-24
Outlet Adjustment.........................................3-29
Passenger Compartment Air Filter...................3-29
Warning Lights, Gages, and Indicators............3-30
Instrument Panel Cluster................................3-31
Speedometer and Odometer...........................3-33
Trip Odometers............................................3-33
Tachometer.................................................3-34
Engine Speed Limiter....................................3-34
Safety Belt Reminders...................................3-35
Airbag Readiness Light..................................3-36
Passenger Airbag Status Indicator...................3-37
Charging System Light..................................3-38
Up-Shift Light...............................................3-38
Brake System Warning Light..........................3-39
Antilock Brake System (ABS) Warning Light.....3-40
StabiliTrak
®/Traction Control System (TCS)
Warning Light...........................................3-41
Engine Coolant Temperature Warning Light......3-41
Engine Coolant Temperature Gage..................3-42
Tire Pressure Light.......................................3-42
Section 3 Instrument Panel
3-1