2009 AUDI Q7 ECO mode

[ i J Tips
• The digital c lock and the odometer are turned on for about 30
seconds when the driver's door is opened.
• When the ignition is turned off, the odometer reading and the
digital clock with date display can be switched on for about
30 seconds by pressing the !CHECK] button~
page 16, fig. 5. •
Speedometer with odometer
The speedometer shows you the vehicle speed, and the
odometer shows you how many miles (kilometers) you
have driven.
Fig. 4 Instrument
c luster Odometer and
reset button
The odometer and trip odometer are located inside the speedom ­
eter.
• USA models - Miles
• Canada models -Kilometers
You can switch the disp lay from miles to kilometers and vice versa
via the MMI.
Lower odometer
The lower odometer shows the total number of miles (kilometers)
driven .
Contro ls and eq uip­
ment
Instruments and warning /indicator lights
Upper odometer (trip odometer)
The upper odometer shows the total number of miles (kilometers)
driven since you last reset the odometer to zero. You can use this
odometer when you want to keep track of how many miles (kilome ­
ters) you have driven for a single trip or errand. The last digit indi­
cates 1/10 of a mile (100 meters).
You can reset the trip odometer to zero by pressing the Reset button
~ o.o.
Malfunction message
If there is a malfunction somewhere in the instrument cluster,
dEF
wil l appear in the trip odometer and will stay on . Contact your
authorized Audi dealer to have the problem corrected .
Immobilizer
When the ignition is switched on, the data on the ignition key are
scanned automatically.
If an unauthorized key was used,
SAFE is displayed continuously in
the odometer display field. The vehicle cannot be operated
~ page 51.
[ i J Tips
• The digital clock and the odometer are turned on for about 30
seconds when the driver's door is opened.
• When the ignition is turned off, the odometer reading and the
dig ital clock with date display can be switched on for about
30 seconds by pressing the
I CHECK] button ~ page 16, fig. 5. •
Fuel gauge
The fuel gauge only works when the ignition is on .
When the needle reaches the reserve mark, the~
page 36
symbo l appears in the instrument cluster display as well as the
message
Please refuel. There are approximately between 2.6 and 3.2 ~
Vehicle care I I Technical data

Instrument cluster illumination
The basic brightness of the illumination for the instru­
ments, the center console and the display can be
adjusted.
F ig . 6 Inst rume nt
c lu st er ill um inatio n
-Press the"+" button to increase the brightness during the
hours of darkness.
- Press the" -" button to decrease the brightness during the
hou rs of darkness.
A light sensor in the instrument cluster controls the il lumination for
the instrument cluster, the center conso le and the displays. In a
bright environment, using the buttons to change the brightness has
no effect .
[ i J Tip s
The illumination for the instrument cluster lights up whenever you
switch on the ignition with the vehicle headlights off. As the
daylight fades, the instrument cluster illumination likewise dims
automatically and wil l go out complete ly when the outside light is
very low. This feature is meant to remind you to switch on the head ­
lights when outside l ight conditions become poor. •
Contro ls and eq uip­
ment
In st ru m ents a nd w arnin g/indi cator li ght s
Warning /indicator lights
Overview
The warning/indicator lights indicate different functions
or a p ossible malfunction .
Fig. 7 Instru me nt clu ste r wi th warnin g/in dic at or l igh ts
Your vehicle is equipped with severa l important warning and indi ­
cator lights to he lp you monitor the continued reliable operation of
your vehicle ::::;>& .
AIR
BAG
E lectronic power cont rol ::::;> page 19
Electronic Stabilization Program (ESP) => page 19
U SA model s: => page 19
Airbag system
Vehicle care I I irechnical data

& WARNING (con tinued)
ext reme caution when worki ng un der th e hood => pa ge 32 4,
"Engin e comp artm ent ".
[ i ) Tips
Many functions are monitored by the Auto -Check system
=>
page 30. Malfunctions or faults wil l be identified either with a red
symbo l (pr ior ity 1 -Danger!) or with a yellow symbol (priority 2 -
Warning). •
Electronic power control r
This warning/indicator light monitors the electr oni c
power control.
The warning/indicator light (E lectronic Power Control) illumi -
nates when you turn on the ignition as a function check .
[ i ) Tips
If this warning/indicator light illumi nates whi le you are driving, then
there is a malfunction in the engine electronics . Have the malfunc ­
tion corrected as soon as possible by your authorized Audi dealer or
qualified workshop .•
Electronic stabilization program (ESP) ~
This warning/indicator light monitors the electronic stabi ­
lization program .
The warning/indicator light has the following functions:
• It blinks while you are dr iving when the ESP is working.
• It illuminates when you switch on the ignition for approximately
2 seconds as a function check.
Controls and equip ­
ment
In st rum ent s a nd w arnin g/indi cato r ligh ts
• It illuminates when there is a malfunction in the ESP .
• It illumina tes when ESP or ASR (Anti -Sl ip Regulat ion) is deact i­
vated .
• It illuminates if there is a malfunction in the ABS, since the ESP
is part of the ABS system.
If the battery termina ls were disconnected and re -connected, the
vehicle was jump started or the battery is
very weak, the ESP senso r
system goes through a learn ing process for the first few yards . The
warning/indicator light i lluminates . The warning/indicator light
goes out as soon as the learning process is complete.
If the ESP warning/indicator light i lluminates and stays on after you
have started the engine, this may mean that the control system has
temporarily switched off the ESP. If this is case, you can reactivate
the ESP by turning the ignition off and then on again. The
warning/indicator light should go out to show that the system is
fully functional again.
For more information about the ESP=>
page 288. •
Airbag system
~i (USA models) / !_~-(Canada models)
This warning/indicator light monitors the airbag and the
tensioner systems .
The i (USA models) f! lt (Canada models) warning light i lluminates
for a few seconds each time you switch on the ignition.
I f the
ffl (USA mode ls) l! go out, or if it illuminates whi le you are driving, or if it starts to blink,
then there is a malfunction somewhere in the system. If the light
does not illum inate when you switch on the ignition, this also
means there is a malfunction. ..,_
I • •

Instruments and warning/indicator lights
& WARNING
If you have a malfunct ion in the airbag system, contact your autho­
rized Audi dealer immediately. Otherwise the airbag or the belt
tensioner may not work properly in an accident. •
Tire pressure monitoring system -telltale
indicator lamp '-)
The warning/indicator light appears in the event of a
significant loss of air pressure .
The ( warning/indicator light il luminates for a few seconds after
the ignition is turned on as function check and then goes out.
If the symbo l appears, pressure is too low in at least one tire.
When the system detects a malfunction, the warning/indicator light
will flash for approximately one minute and then remain continu­ ously i lluminated . This sequence wi ll continue upon subsequent
vehic le starts up as long as the malfunction exists. Contact your
authorized Audi dealer and have the malfunction corrected .
For more information
=> page 44. •
Turn signals ¢ Q
The indicator light blinks when you use either turn signal.
Whenever you use the left ¢i or the right¢ turn signal, the ind icator
light blinks. When you use the emergency flashers, both indicator
lights flash .
If one of the turn signal light bulbs burn out, the turn signal will
blink twice as fast as normal.
This does not apply, however, in towing mode . The indicator light
does not flash if a turn signal is out on the trailer or the towing
vehic le. Additional information on the turn signa ls=>
page 77 . •
App lies to vehicles: wi th tow ing h itch
Trailer turn signal assembly ¢ 19
The indicator light also blinks if the turn signal is operated
when towing a trailer.
The indicator light ¢1i> bl inks when the turn signal is used, if a trailer
has been properly connected to the vehicle.
If one of the turn signa l bu lbs on the trailer is burned out or defec ­
tive, the indicator light will not b link when you use the turn signals.
[ i ] Tips
For vehicles with a factory installed towing hitch or a trailer hitch
that was installed later according to factory specifications, the
trailer turn signa l assembly is actuated. •
Malfunction Indicator Lamp (MIL) :,
The Malfunction Indicator Lamp (MIU is part of the On-Board Diag ­
nostic (OBD II) system. The symbo l lights up when the ignition is
turned on and will turn off after the engine has started and has
settled at a constant idle speed . This indicates that the MIL is
working properly.
The warning light il luminates when there is a malfunction in the
engine electronic system. Contact your authorized Audi dealer and
have the malfunction corrected.
An improperly closed fuel filler cap may also cause the MIL light to
illuminate
=> page 327.
For more information => page 29. •

Applies to vehicles : w it h l ane ass ist
Lane assist (system is ready) /:
The indicator light shows that the system is ready to use. A warning
a lerts the driver when the vehicle drives over detected lane
boundary lines .
More information about lane assist=>
page 171. •
Applie s t o vehi cles: wit h lane ass is t
Lane assist (system is not ready) •
The indicator light shows that the system is turned on but unable to
send a warning .
More information about lane assist =>
page 171. •
Safety belts i
This warning/indicator light reminds you to put on y our
safety belt.
The , ff-warning /indicator light i lluminates when the igni tion is
switched on to remind the d river and (on USA models only) any front
passenger to put on the safety belt . Additionally, an acoustic
warning (gong) will also sound.
For more Informa tion=>
page 231 , "Safe ty belt warning light~".•
App lies to vehic les: wit h Adaptive Air Suspe nsion
Adaptive Air Suspension ... :::>
This warning/indicator light has the following functions:
• It illum inates for a few seconds af ter the igni tion is turned on as
function check and then goes out.
Controls and equip ­
ment
In st rum ent s a nd w arnin g/indi cato r ligh ts
• If the warn ing/indicator light illuminates or blinks continuously,
there is a system fau lt in the Adaptive Air Suspension. A system
faul t can result in limited ride comfo rt and
low g ro und cle ar an ce .
Drive safely to the nearest authorized Audi dealer or qualified work ­
shop, and have the fault correc ted.
• If the warning /indicator light flashes, you should not drive the
vehic le . The flashing warning /indicator light points to an extreme
High level. A very
pronounced lifting of the vehic le (extreme High
level) can resu lt, for example, when a heavy load is removed from
the vehicle. As soon as the level has returned to normal, the
warning/indicator light stops flashing, and you can drive away .
• If the warning /indicator light flashes in conjunction with the
a,
warning /indicato r light , you should not drive off immediately in
order to prevent damage to the underbody . The two warning /indi ­
cator lights flashing together points to an extreme Low level. A very
pronounced lowering of the vehicle (extreme Low level) can result,
for examp le, from a heavy load. As soon as the level has returned to
nor mal, th e warning/indicator lights stop flashing, and you can
drive away.
0 Note
If the wa rning/indicator light flashes in conjunction with the a,
warning/indicator light, you should not drive the vehic le because
low -lying vehicle parts can bottom out as you drive over uneven
ground and be damaged as a resul t.•
Applies to ve hic les: w ith A dapt ive Air Suspensi on
Adaptive Air Suspension c.:,
This warning /indicator light has the following functions :
• It illuminates for a few seconds after the ignition is turned on as
function check and then goes out. ..,
I • •

Instruments and warning/indicator lights
• It comes on for approximately 15 seconds as a warning of
reduced ground clearance, if the dynamic mode is activated and if
the ignition is switched on~
page 207, "Chassis controls".
• If the warning/indicator light flashes in conjunction with the ;,
warning/indicator light, you should not drive the vehicle immedi­
ately in order to prevent damage to the underbody. The two
warning/indicator lights flashing together points to an extreme Low
level. A very
pronounced lowering of the vehicle (extreme Low level)
can result, for example, from a heavy load. As soon as the level has
returned to normal, the warning/indicator lights stop flashing, and
you can drive away.
0 Note
If the warning/indicator light flashes in conjunction with the
warning/indicator light, you should not drive the vehicle because
low-lying vehicle parts can bottom out as you drive over uneven
ground and be damaged as a result. •
High beam ~D
The ~D warning/indicator light illuminates when the high beams are
on or when you use the headlight flasher. For more information
about using the high beams, see~
page 77. •
Cruise control
CRUISE (USA models) /(7)'2 (Canada models)
The warning/indicator light illuminates when the cruise control is
activated. •
Anti-lock brake system (ABS)
.. c_ (USA models)/ ~ (Canada models)
This warning/indicator light monitors the ABS and the
electronic differential lock (EDL).
The warning/indicator light will come on for a few seconds when the
ignition is switched on . The light will go out after an automatic
check sequence is completed.
There is a malfunction in the ABS when:
• The warning/indicator light does not illuminate when you switch
on the ignition .
• The warning/indicator light does not go out after a few seconds.
• Th e warning/indicator light illuminates while driving.
The brake system will still respond even without the assistance of
the ABS system. See your authorized Audi dealer as soon as
possible to restore full braking performance.
For more information
regarding the ABS~
page 292.
The ABS warning light and the brake warning light come on
together. The ABS will not work and you will notice a change in
braking response and performance .
Malfunction in the brake system
If the brake warning light~ page 23and the ABS warning illuminate
together there may be a malfunction in the ABS, and there may also
be a malfunction in the brake system itself~& .
In the event of a
malfunction in the brake system the warning/indi ­
cator light
BRAKE (USA models)/ ((D) !Canada models) in the instrument
cluster flashes. By pressing the
!CHECK] button, you can bring up a
driver message which explains the malfunction in more detail.
Please note
~ page 32. .,.,

Instruments and warning/indicator lights
& WARNING (continued)
• Canada models: If the brake warning light «D> and the ABS
warning light come on together, the rear wheels could lock up
first under hard braking . Rear wheel lock-up can cause loss of
vehicle control and an accident. Have your vehicle repaired imme­ diately by your authorized Audi dealer or a qualified workshop .
Drive slowly and avoid sudden, hard brake applications.
• If the brake warning/indicator light does not go out after a few
seconds and the parking brake released, or lights up while you are
driving, the fluid level in the brake fluid reservoir is too low . If you
believe that it is safe to do so, proceed immediately at low speed
to the nearest authorized Audi dealer or qualified repair facility
and have the brake system inspected.
• Always keep in mind that after several brake applications, you
will need greater pressure on the brake pedal to stop your vehicle. Do not rely on strained brakes to respond with maximum stopping
power in critical situations. You must allow for increased braking
distances . The extra distance used up by fading brakes could lead
to an accident. •

Digital speedometer
Fig. 11 Display: Digital
speedometer
Current speed appears in the display . Speed is shown in 1 mph
measures (USA models) or 1 km/h measures (Canada models).
You can switch the display from miles to kilometers and vice versa
via the MMI. •
Open door or trunk lid warning
The pictogram alerts you when doors or the rear lid have
been left open.
Fig . 12 Display: open
door or rear
lid
warning
With the ignition switched on, the open door or rear lid warning illu ­
minates when at least
one door or the hood or the trunk lid is not
Con tro ls and eq uip­
ment
Driver information display
closed. The symbol also shows you which door(s) or lid is not
closed.
In the illustration=> fig. 12 it is the driver's door, the left rear door
and the rear lid. As soon as all the doors, the hood, the rear lid and
the fuel filler cap are properly closed, the door and rear lid warning
turns off and the Driver Information System functions selected are
displayed again .•
Defective light bulb warning
The defective light bulb warning tells you when a vehicle
light bulb has become defective.
Fig. 13 Display: defec­
tive light bulb warning
The defective light bulb warning monitors the function of the light
bulbs . If this symbol illuminates, a brake light, a turn signal (front
or rear), a headlight, the backup light, a fog light or a rear fog light
has failed.
& WARNING
• Light bulbs are pressurized and could explode while they are
being changed causing serious personal injury.
• Work with due care when handling the high-voltage section of
gas discharge (xenon) lights. Failure to do so could result in death
or serious injury . ..,
Vehicle care I I Technical data