2009 AUDI Q7 sensor

• The proximity sensors are deactivated after a few days to save
power. You then have to pull on the door handle once to unlock the
vehicle and a second time to open the vehicle .
• To prevent the ba ttery from being discharged and to preserve
your vehicle's ability to start for as long as possible , the energy
management system gradual ly swi tches off unnecessa ry conve ­
nience functions. It is possib le that you will not be ab le to un lock
your vehicle using these convenience functions .•
Ap plie s to v ehicl es: with Co nven ie nce key
Locking the vehicle
The vehicle can be locke d wi thout operati ng the master
key.
F ig . 4 8 Co nve nien ce
k ey : Lo cking t he
ve hicle
- Move th e se lect or lever to t he P posit ion.
- Press the locking butto n in the doo r handle to lock the
ve hicle ~ & -
The vehicle can be locked at any door. The authorized master key
only has to be within a range of about 5 feet (1 .5 meters) from the
part icular door.
The se lector lever must be in the P position, otherwise the vehicle
can not be locked.
Controls and equip ­
ment
Opening and clo sing
& WARNING
• When you lock your vehicle from out side , nobody -espe cially
children -should remain inside the vehicle . Remember , when you
lock the vehicle from the out side the windo ws ca nnot be opened
from the in side .
• When you leave the vehi cle , al wa ys remo ve the ignition key and
t ak e it with you. Thi s will prevent pa ssenger s (children , for
e x ample ) from a ccident ally b ein g locked in the vehic le should they
accidentally pre ss the power locking swit ch in the front door s.
• Do n ot lea ve ch ildren in side the vehi cle un supe rvis ed . In an
emergency it would be impo ss ible to open the doors from the
out side w ithout the key .
[ i ] Tips
It is not possib le to re -open the door for a brief period directly after
c losing it. This allows you to ensu re that the doo rs are properly
locked .•
Anti-theft alarm system
The anti- theft al arm triggers an alarm if anyone at tempts
to break i nto the vehicle.
The anti -theft a larm system triggers an audible alarm and turns on
the emergency flasher if an unauthorized interference w ith the
vehic le is sensed by the system.
How i s the anti -theft alarm system switched on ?
The anti-theft alarm system is switched on when you lock the
vehicle . The system is activated approximately 30 seconds after the
vehic le is locked. The indicator light on top of the door trim start
flashing rapid ly for 30 seconds and then b link slowly. .,..
I • •

Clear vision
Lights
Switching the headlights on and off ·'t!-·
In the "AUTO" position, a light sensor* automatically
switches the head- and taillights on and off in response to
light conditions.
Fig. 60 Instrument
panel : light switch
The light switch must not be overturned past the stops in
either direction.
Switching on automatic headlight control
-Turn the light switch to AUTO=> fig. 60.
Switching on the side marker lights
-Turn the light switch to ~oo:.
Switching on the headlights and high beam
-Turn the light switch to ~D.
- Push the high beam lever forward towards the instru-
ment panel=>
page 77.
Contro ls and eq uip­
ment
Switching off the lights
- Turn the light switch to 0. Clear vision
The headlights only work when the
ignition is switched on . While
starting the engine or when switching off the ignition, the head ­
lights will go off and only the side marker lights will be on.
After starting the engine, the headlights are automatically adjusted* to the load and angle of the vehicle (for example, during
acceleration, braking). This prevents oncoming traffic from experi­
encing unnecessary headlight glare from your headlights.
If the system is not operating properly, a warning symbol in the
Auto -Check Control is displayed
=> page 37.
With the side marker lights or headlights switched on, the symbol
next to the light switch illuminates
coo:.
Daytime running lights
• USA models:
On vehicles with xenon lights the daytime running
lights will come on automatically when the ignition is turned on and
the light switch=> fig. 60 is in the
O position or the AUTO position
(only in daylight conditions). The
Daytime running lights function
can be turned on and off in the MMI menu
Exterior lighting
=> page 74. On vehicles with halogen fights, daytime running lights
can be activated by your authorized Audi dealer=>
f.1.
• Canada models: The daytime running lights will come on auto ­
matically when the ignition is turned on and the light switch
=> fig. 60 is in the O position or the AUTO position (only in daylight
conditions)
=> /.1 .
Automatic headlight control*
In the switch position AUTO the automatic headlight control is
turned on . The low beams and tail lights are turned on automatically
through a light sensor as soon as ambient brightness (e.g . when
driving into a tunnel) falls below a value preset at the factory. When ..,_
Vehicle care I I irechnical data

Clear vision
ambient brightness increases again, the low beams are turned off
again automatica lly => & .
In the
AUTO pos ition the low beams are switched off automatically
when the ignition is turned off .
L ight S ensor M alfu nction *
In the event of a ligh t sensor mal func tion, the drive r is notified in the
ins trument cluster display :
e. Automatic headlights /autom ati c w ipers defe ctive
For safety reasons the low beams are turned on permanently with
the switch in
AUTO . However , you can continue to turn the lights on
and off using the light switch . Have the light sensor checked as soon
as possible at an authorized Audi dealer or qualified workshop.
& WARNING
• Never use d ayt ime running lights to see where you are going.
The y are no t bright enough and will not let you see far enough
ahead for safety , espe cially at du sk or when it is d ark . Al way s
switch on the low beams at du sk or when it is dark .
• Automati c he adlights* are onl y intended to assist the driver .
They do not relieve the driver of his re sponsibility to check the
headlight s and to turn them on manually a ccording t o th e cur rent
light and visibility condit ion s. For example , fog and ra in cannot be
dete cted by the l ight sen sor s. S o alwa ys sw itch on the headlight s
under th ese weather condition s and wh en driv ing in the dark
t D .
• Cras hes c an happen when y ou cannot see th e road ahead and
when you cannot be seen by other motori sts.
- Alway s turn on the headlights s o that you can see ahead a nd
s o that others can see your c ar from the ba ck.
[ i ] Tips
• With the switch in AUTO front fog lights and rear f og lights
cannot be turned on in addition . • T
he light sensor * for headlight control is located in the rear view
mirror mount . Do no t apply any stickers to the windshie ld in this
area to prevent malfunctions or failures .
• I f you remove the ign itio n from the ign ition lock while the head­
lights are still on, a bu zzer will sound as long as the driver's door is
open to remind you to turn off the lig hts.
• Always observe the specific local regulations for your ar ea as to
when to use you r lights .•
Adjusting exterior lighting
The functions are set in the MM/ .
Fig . 61 MM I display :
E x te rior lighting
- Press the [ CAR ] fu nct io n butto n.
- Selec t
Exterior lighting . The menu Exterior lighting
appears=> fig. 61.
C oming h om e*
T he
Com ing home function ensures that after turn ing off the igni­
tion and op ening the driver's doo r
the vehicle periphery is il lumi ­
nated in the dark. In addition , the front fog lights, the tail lights and
the license plate light are turned on . On- time can be set fo r a period
from
O (off) to 60 seconds. .,,_

Wiper and washer system
Front windshield wipers ~
The windshield wiper lever controls both the windshield
wipers and the washer system.
Fig. 75 Windshield
wiper lever
The windshield wiper lever~ fig. 75 has the following posi­
tions:
Intermittent wiping <5;?1 (activating rain sensor*)
- Move the lever up to position 0).
- Move switch @up or down, to change the intervals or to
adjust the sensitivity of the rain sensor*.
Low wiper speed
-Move the lever up to position ®·
High wiper speed
- Move the lever up to position G).
Con tro ls and eq uip­
ment
Clear vision
One-touch wiping
- Move the lever to position @, when you want to wipe the
windshield
briefly.
Automatic wiper/washer
- Pull the lever to position © (toward the steering wheel)
and hold.
- Release the lever. The washer stops and the wipers keep
going for about four seconds. Depending on how long
the lever is held, different numbers of wash cycles are
performed.
Turning off the wipers
- Move the lever back to position @).
General information
The windshield wipers and the windshield washer system operate
only with the ignition on.
During a temporary stop, e .g. at a tra ffic signal, the set wipe speed
is automatically reduced by one stage.
The windshield washer nozzles are heated at low temperatures
when the ignition is on.
Removing water droplets
About 5 seconds after the wash cycle is complete, the wiper system performs a single automatic wipe cycle to remove any water drop­
lets that remain on the windshield.
If you would like to deactivate this delayed wipe cycle while driving,
you have to pull the lever to position © again within 10 seconds
after this wipe cycle.
Water droplet removal is reactivated after the ignition is switched off and then on again.
~
Vehicle care I I irechnical data

Clear vision
Wint er p osition
To speed up de -icing of the windshie ld w ipers, they move to the
winter position when the ignition is switched off and at an outside
temperature below 39 °F (4 °C). In this position, the windshie ld
w ipers are in an area on the glass which is reached by the air vents
below the glass . It is a lso easier to remove snow and ice from the
windshield wipers in this position .
The wipers leave the winter position, when the ignition is switched on, if the wi ndshield wiper lever is ope rated or the active rain
sensor* reacts to moisture.
Rain sen sor*
The rain sensor operates only in the interval wiper position. When it
s tarts to rai n, the interval wiper m ode is ac tivated aut omatically.
If the windshield wiper lever is in the interval wipe position with the
igni tion switched off, the rain sensor is not activated unti l vehic le
speed is above 4 mph (6 km/h).
To reduce the sensitivity of the rain sensor, the switch@ must be
moved down . T o in crease the se nsitivity of the rain sens or, the
switch must be moved up .
The higher the sensi tiv ity se tting, the so oner the w indshield wipe rs
react to mo isture on the windsh ield. Increased sensitivity is
signa led by the windshie ld wipers making a single pass over the
windsh ield.
The rain sensor wiper intervals depend on the sensitivity setting as
we ll as veh icle speed . D uring b rie f stops, wiper m otio n will adjust in
relation to the amount of rain on the windshield .
& WARNING
• Wiper blades are cru cial for safe driving! Only when they are in
good condition are they able to clear the window s proper ly to
p rovide un comp romised visibil ity . Worn or damaged wiper blades
are a safety hazard =>
page 84, "In stalling new wiper blades "!
& WARNING (continued )
• The rain sensor* is only designed to assist and support the
driver . It remain s entirely the dr iver' s re spon sibility to monitor
out side weather conditions and to manually activate the wipers as
s oon a s rain or driz zle reduce s vi sibility through the wind sh ield .
0 Note
In freezing o r near freez ing conditions:
• Always check that the wiper blades are not frozen to the glass
before you turn the wipers on. Loosen a wiper blade which is frozen
in place before operating the wipers to prevent damage to the wiper
blade or the wipe r motor.
• Do not use the wipers to clear a frosted window. Using the
wipers as a convenient ice scraper wi ll destroy the wiper blades .
• Before you ta ke you r vehicle to an automatic car was h, ma ke s ure
you have the windshield wiper system switched off (lever in position
0), otherwise the windshield wiper system could get damaged in the
car wash if it should sudden ly come on .
[ i ] Tips
• The rain senso r* is part of the interva l wiping syste m. Turning o ff
the ignition will also deactivate the rain sensor. To reactivate the
s en sor, switch o ff the interval wip ing funct ion, then sw itch it bac k
on again.
• Worn or dirty winds hield wiper b lades cause smearing which
can affect the operation of the rain sensor *. Check the condition of
your windshield wiper blades regularly .
• Make sure the washer fluid reservoir in the engine compartment
is topped o ff be fore go ing on a long trip. Look up=>
page 346 for
check ing and filling the washer container. •

Applies to vehicles : wit h automat ically di mmi ng in side mirr or
Automatically dimming inside mirror
The automatic dimming function can be turned on and off
if required.
Disabling auto dimming
Fi g. 8 1 In side r ear
v iew mirror
- Press butto n @ ~ fig. 8 1 briefly, -th e gree n indicator
light @ goes out .
A ctivating /re activ ating auto dimming
- Press button@
briefly, -the green indicato r light @
goes on.
Automa tic dimming func tio n
The automatic dimming function is activated every time the ignition
is turned on . The green indicator light is lit to indicate auto dimming
is active.
When dim ming is activated, the inside m irror will darken
automati ­
cally
in response to the amount of light striking the mirror (such as
headlights from rearwa rd approaching vehicles). Even in dimm ing
mode, the mirror surface turns bright when :
• the interior light is switched on
• reverse gear is engaged .
Controls and equip­
ment
Cl ea r vision
& WARNING
The glas s of the in side re ar vie w mirror i s layered and cont ain s an
electrolyte to a chieve it s properties. Be aware of liquid electrolyte
leaking from a bro ken mirror gl ass. Thi s liquid can cause irrit ation
to skin , eyes , and re spir atory sy ste m . If you get el ectrolyte in your
e ye s or on your skin , immed iatel y rinse w ith plenty of w ater.
If irri ­
t a tion per sists, s eek medical attention .
0 Note
Liquid electrolyte leaked from a broken mirror glass wil l damage any
p lastic surfaces it comes in contact with . C lean up sp illed e lectrolyte
immediately with clear water and a sponge .
[ i ] Tip s
• If you sw it c h off the automati c di m mi ng function on the in side
mirror , autom atic dimming of the out side mirrors* will likewise be
dis abled .
• Check to make sure there are no objects preven ting light from
reaching the inside mirror.
• Do not attach any stickers to the windshie ld in front of the light
sensor*, as this would interfere with the automatic operation of the
headlig hts and the automatic d imming of the inside mirror.
• Be aware that automatic dimming of the inside mirror can only
operate properly if the rear window sun b lind* is retracted. •
I • •

• .___w_ a_ rm __ a_ n_ d_ c_o _l_d ________________________________________________ _
passenger's side and to the outer rear seats. The new temperature
is shown in the display .
By simultaneously pressing and holding the contro l knobs on the
driver's side and front passenger's side, the temperature setting on
the driver's side can be switched to the front passenger's side. The new temperature is shown in the disp lay.
[ i J Tip s
The gri lle between the (ECON ON/OFF] and (SETUP] buttons must
remain unobstructed and must not be taped over. Measur ing
sensors are located behind it. •
Turning on and off [ECON ON/OFF]
Turning the air conditioning on
- Press [ECON ON/O FF] briefly, or
- Press [AUTO].
Turning the air conditioning off
Press the I ECON ON/OFF I button for at least 2 seconds to
switch the a ir cond itioning off and to block the air supply
f rom t he ou tside .
"OFF" appears in the display .
Switching air conditioning on /off
- Switching the a ir conditioning system on/off is done wit h
c limate control switched on .
- Press the [ECON ON/OFF] button just
briefly.
The air conditioner tu rns back on if you press one of the control
buttons or the control knob.
ECON operation is indicated by the glowing LED on the right next to
the word ECON. T
he air conditioning (compressor) is turned off in ECON mode.
"ECON" means "Economy". You save fuel by switching off the air
conditioning=>
page 131.
Please note that vehic le interior temperature cannot be lower than
t he outside temperature in the ECON mode. The air is not cooled or
dehumidified. This can cause the windows to fog up.
[ i J Tip s
With the ignition turned off, you can activate the residual heat func­
tion by pressing the
[ECON ON/OFF] button . The residual heat from
the coolant can be used to heat the vehicle interior. •
Automatic mode [AUTO)
The automatic mode is the standard setting for all
seasons.
Turning on AUTO
Select temperature between 60 °F (+16 °C) and 84 °F
(+28 °C).
P ress [ AUTO I => page 125, fig . 135.
Automatic operation ensures constant temperatures in the interior
and dehumidifies the air inside the vehicle. Air temperature, vo lume
and distribution are contro lled automatica lly to reach or maintain
the desired inter ior temperature as quickly as possible. Fluctuations
in exterior temperature and the effects of temperature from the
pos ition o f the sun are compensated for automatica lly.
T his operating mode works only in the adjustable temperature
r ange, from 60 °F (+ 16 °C) to 84 °F (+28 °C). If a temperature below
60 °F
( + 16 °C) is selected, LO appears in the disp lay. At temperatures
above 84 °F ( +28 °C),
HI is d isplayed . At both extreme settings,
climate contro l runs continuously at maximum cooling or heating
power. There is no temperature regu lation .•

• .___w_ a_ rm __ a_ n_ d_ c_o _l_d ________________________________________________ _
Basic settings (SETUP]
General
The basic settings for the climate control are performed in
the!SETUP] menu.
Fig . 142 MM I D isp lay:
Set up c li m ate control
T he basic settings for the air cond itioning can only be made
with MM I turned on .
- Press the (SETUP) button in the controls to access the menu.
- Selec t the des ired fu nction using t he co ntrol knob (dr iver
or passenger) in t he air conditioning contro ls.
The fol lowing functions can be selected :
• ECON~
page 134
• Auto recirc. ~ page 134
• Synchron. ~ page 135 or~ page 135
• Rear operation*~ page 135
G)ECON
When the EC ON function is on~ page 134, this symbol appears in
the status line.
0 Synch ron.
When the Synchron. function is on~ page 135 or~ page 135, this
symbo l appears in the status line .
© Auto recirc.
When the Auto rec irc. function is on~ page 134, this symbol
appears in the status line. •
ECON
The ECON mode helps to save fuel .
The air conditioning is turned off in ECON mode. "ECON" means
"Economy" . By switching off the air conditioning (compressor) , you
save fuel.
P lease note that vehic le interior temperature cannot be lower than
the outside temperature in the ECON mode. The air is not cooled or
dehum id ified.
If the vehic le interior becomes too hot or if the windows fog up,
ECON mode should be turned off . As soon as the [AUTO ] button in
the air conditioning controls is pressed , the system automatically
leaves the ECO N mode, and the air conditioning compressor is
turned on again .•
Automatic recirculation mode
An air q uality sensor detects increased concentrations of
pollu tants in the outside air and automatically switches
t o recirculation mode.
We recommend that you always keep automatic air recirculation ON
to prevent polluted outside air from entering the vehicle interior.
If the
air quality sensor located in the air conditioning system
detects po lluted outside air, the sensor decides whether the air
po llution can be reduced by the factory -installed pollutant filter or
whether it is necessary to switch to air recirculation. With heavy ...