2009 Alfa Romeo 8C light

148
6
CD
E
F
Remove the cigarette lighter
C, and insert the
connector
D.
Start the engine by pressing the start button (see
page 114).
Press the Fix&Go button
E at position “I”. The
electric compressor will activate and the liquid
with air will inflate the tyre.
A pressure of at least 1.8 bar (26 psi) should
be reached within 20 minutes. If this does not
occur, turn off and remove the Fix&Go kit.
Move the vehicle forward and backward by 10
metres to better distribute the sealant in the tyre.Attach the quick-connector of the compressor
directly on the tyre valve and repeat the inflation
procedure.
If the minimum tyre pressure is not reached,
do not start the vehicle. Contact an Authorised
Service Centre of the Manufacturer’s
Network.
When the correct pressure has been reached,
move the vehicle forward and backward to
evenly distribute the sealant in the tyre.
After 10 minutes, stop and check the tyre
pressure. If the pressure is below 1.3 bar
(19 psi), do not drive the vehicle. The tyre is
excessively damaged. Contact an Authorised Service Centre of the
Manufacturer’s Network.
If the pressure is equal to or greater than 1.3
bar (19 psi), repeat the inflation procedure until
reaching the adequate tyre pressure and resume
driving.
Remove the warning label
F from the bottle and
position it on the dashboard as a reminder to
the driver that the tyre has been treated with
automatic Fix&Go.

149
6
IN AN EMERGENCY
CAUTION
Do not exceed the speed limit
of 110 Km/h (65 miles/h). Have the
tyre checked as soon as possible at
an Authorised Service Centre of the
Manufacturer’s Network.
CAUTION
The sealant may be noxious or
irritating. Do not swallow and avoid
contact with the skin and eyes. In the
event of contact, rinse with abundant
water.
Consult a doctor in case of an allergic
reaction. Keep the sealant out of
children’s reach. Dispose of the empty
sealant bottle at an Authorised Service
Centre of the Manufacturer’s Network.
WARNING: Replace the bottle of sealant before
the expiry date at an Authorised Service Centre
of the Manufacturer’s Network. WARNING: The sealant contained in the bottle
of the Fix&Go kit may damage the sensor fitted
inside the wheel rim on vehicles equipped with
the tyre pressure monitoring system. In such
cases, the sensor must always be replaced
by an Authorised Service Centre of the
Manufacturer’s Network.
IF AN EXTERIOR
LIGHT GOES OUTWARNING: Before replacing a light bulb, make
sure that the corresponding fuse is in proper
working condition. For replacement, use only
genuine new light bulbs having the same
characteristics as the bulb to be replaced.

150
6
E
F
HG
A
B
C
D
HEADLIGHT CLUSTERS
To access the headlight bulbs can be accessed
from underneath the vehicle, after removing the
wheel housing.
The light bulbs of the headlight clusters are
arranged as follows:A - Position light bulb B - Direction indicator light bulbC - Bi-xenon low-beam/high-beam bulbD - DRL bulb (on vehicles manufactured for the
Japanese market, they are not operational;
for all the other markets where by law
they may not be turned on, they can
be deactivated from the multifunction
display).
CAUTION
Have the Xenon lamps and
low-beam/high beam bulbs replaced
and the system checked only at an
Authorised Service Centre of the
Manufacturer’s Network. RISK OF
ELECTRICAL SHOCKS!
It is advisable to contact an Authorised Service
Centre of the Manufacturer’s Network also for
replacement of the DRL, position and direction
indicator bulbs.
TAILLIGHT CLUSTERS
The taillight bulbs are arranged as follows:E - Position and stop lightF - Reverse light bulbG - Rear fog light bulbH - Direction indicator LED
Given the complexity of the operation, we
advise you to have the taillight cluster bulbs
replaced at an Authorised Service Centre of the
Manufacturer’s Network.WARNING: For the countries that drive on the
left, the reverse lights and rear fog lights are
inverted.

151
6
2
1
K
J
L
M
IN AN EMERGENCY
DIRECTION INDICATOR
LIGHTS
To replace the direction indicator light bulb (5W):
1) Push the direction indicator forward to
compress the spring clip
J. 4) Remove the bulb
M and replace it.
5) Refi t the bulb holder turning it clockwise.
6) Refi t the direction indicator inserting fi rst
the retaining tab on the rear part and then
pressing the front part until hearing the
spring clip click into position.
WARNING: Proceed with care when removing
the side direction indicator light to avoid
damages to the vehicle body or to the indicator
itself.
2) Remove the rear part of the indicator by
releasing the catch
K and remove the unit.
3) Remove the bulb holder L by turning it
anticlockwise.

152
6
N
P
3) Replace the snap-fi tted bulb
P.
4) Refi t the bulb holder
N inserting fi rst the
electrical connector side and then pressing
on the other side to hook up the clip. THIRD STOP LIGHT
In order to replace the bulbs, you must remove
the light cluster. It is therefore advisable to
contact an Authorised Service Centre of the
Manufacturer’s Network. NUMBER PLATE LIGHTS
To replace the number plate light bulb (C 5W):
1) Release the dome light by gently prising on
the side with a screwdriver.
2) Remove the unit and turn the bulb holder.

153
6
A
BC
IN AN EMERGENCY
IF AN INTERIOR
LIGHT GOES OUTWARNING: Before replacing a light bulb,
make sure that the corresponding fuse is in
proper working order. For replacement, use
only genuine new light bulbs having the same
characteristics as the bulb to be replaced.
FRONT DOME LIGHT
To replace the bulbs:
1) Gently prise with a screwdriver
A and
remove the dome light.
2) Replace the bulb:
- timed light
B (12V - 10W cartridge lamp)
- reading light C (12V - 3W).3) Refi t the cover inserting fi rst the left part
and then pressing the right part into seat.
WARNING: When refitting the dome light,
make sure that the electric wires are correctly
positioned and do not interfere with the dome
light edges and with the retaining tabs.

154
6
E
F
D
REAR PILLAR LIGHTS
To replace the bulb (12V - 5W cartridge type):
1) Remove the light by levering it out gently
with a screwdriver at point
D.
2) Replace the bulb.
3) Refi t the light inserting fi rst the electrical
connector side and then pressing the other
side until fi tting the light into its seat.GLOVE COMPARTMENT
LIGHT
To replace the bulb:
1) Remove the transparent cover by levering it
out gently, using a screwdriver, at point
E.2) Raise the cover
F.

155
6
H
L
G
IN AN EMERGENCY
3) Replace the bulb
G.
4) Refi t the cover, inserting fi rst the two-tab
side and then pressing on the other side.COURTESY LIGHTS
UNDER THE DOOR AND
THE DASHBOARD
To replace the bulb:
1) Use a screwdriver positioned at point
H to
lever out the light fi xing frame and remove
it.2) Turn the bulb holder
L and remove it.
3) Replace the snap-fi tted bulb
M