2009 Acura TL lock

The engine start/stop button may be
used to stop the engine due to an
emergency situation even while
driving. If you must stop the engine,
do either of the f ollowing operations:
Press the engine start/stop button
twice with your f oot of f the brake
pedal to change the power mode to
VEHICLE OFF (LOCK).
Bef ore leaving the vehicle, make
sure it is of f . You can verif y if the
power is of f by checking the engine
start/stop button LED indicator.
If you open the driver’s door in the
ACCESSORY mode, a beeper will
sound. You will also see a ‘‘TO
TURN VEHICLE OFF:’’ message on
the multi-information display. Press and hold the engine start/
stop button for three seconds.
Firmly press the engine start/stop
button three times.
Do not press the button while driving
unless it is absolutely necessary f or
the engine to be switched of f . If you are driving, the power mode
switches f rom ON to ACCESSORY
or VEHICLE OFF (LOCK)
whenever you perf orm either
procedure. However, the steering
wheel will NOT lock.
Bef ore leaving the vehicle, make
sure it is in VEHICLE OFF (LOCK). If you cannot stop the engine by
pressing the engine start/stop
button once when the vehicle is
stopped and the shif t lever is in Park,
do either emergency engine stop
procedure. In this case, the power
mode will change to VEHICLE OFF
(LOCK), however, the steering
wheel may NOT lock.
K eyless A ccess System
Emergency Engine St op
184
\f—
—y
\f\fy
) \f\fy\f
y
2009 TL

CONT INUED
If you take the keyless access
remote out of the vehicle and close
the door with the power mode ON,
the inside and outside beepers sound
and a ‘‘KEYLESS REMOTE NOT
DETECTED’’ message will be
displayed on the multi-inf ormation
display.The engine does not start if you push
the engine start/stop button when
theremoteisoutsidethevehicle.
Check where the remote is. Make
sure that you carry the remote with
you when you operate the engine
start/stop button.
The displayed message goes away
when you bring the remote back
inside the vehicle.
If the engine is running and you take
the remote out of the vehicle, it will
continue to run. Once the power
mode is changed to VEHICLE OFF
(LOCK), the engine will not restart
until you bring back a remote into
the vehicle.
Even when the remote is inside the
vehicle, the beeper may sound when
the location of the remote is not
detected due to surrounding
conditions. It is not a f ailure. Make
sure that you carry the remote with
you.
K eyless A ccess System
K eyless Remot e Not Det ect ed
Beeper and Message
Inst rument s and Cont rols
185
\f—
—y
\f

y
) \f\fy\f
\fy
2009 TL

Thebatteryintheremotenormally
last about 2 years. To ensure
maximum battery life, do not store
the remote close to electrical devices
such as computers or TVs. When the
multi-inf ormation display shows
‘‘CHANGE KEYLESS REMOTE
BATTERY,’’ replace the battery as
soon as possible (see page ).If the remote battery becomes weak
and the power door lock/unlock
operation is disabled, you should
insert the remote into the keyless
access remote slot to set the power
mode and start the engine. Af ter
inserting the remote to the slot,
operate the engine start/stop button
as previously described (see pages
and ). For more information
on the keyless access slot, see page .
Inserting the remote does not charge
the remote battery. You should
replace the battery as soon as
possible.
The outside beeper sounds when the
power mode is in ACCESSORY, and
a door is opened, then closed.
175178181
189
K eyless A ccess System
K eyless Remot e L ow Bat t ery
186
\f—\f—y
\fy
) \f\fy\f

y
2009 TL

This switch is in the glove box. You
can cancel the keyless access system
f eatures, which are locking/
unlocking the doors, unlocking the
trunk, and starting the engine while
carrying the keyless access remote.
To cancel the system, turn the
keyless access system main switch
of f by pushing it down.Turning of f the keyless
access system will disable lockout
prevention.
With the keyless access remote
system main switch of f , you should
insert the keyless access remote into
the keyless remote slot to start the
engine. For more inf ormation, see
page . According to the message on the
multi-inf ormation display, this
indicator has two indications. A
‘‘CHECK KEYLESS ACCESS
SYSTEM’’ message indicates a
problem with the keyless access
system. A ‘‘CHECK KEYLESS
STARTING SYSTEM’’ message
indicates a problem with the keyless
starting system.
This indicator normally comes on f or
several seconds when you change
the power mode to ON.
189
CONT INUED
K eyless A ccess System
K eyless Access Remote System
Main Switch
K eyless Access System
Indicator
Inst rument s and Cont rols
187
NOTE:
OFF
MAIN SWITCH
\f—\f—\fy
y
) \f\fy\f
y
2009 TL

Have your vehicle checked by your
dealer if :The keyless access system
indicator comes on and stays on
while you are driving.
The indicator comes on af ter the
engine has started. In this case, use the built-in key to
lock/unlock the doors and insert the
keyless access remote into the slot
to start the engine (see page ).
Have your vehicle checked by your
dealer if :
The multi-inf ormation display
shows ‘‘CHECK KEYLESS
ACCESS SYSTEM.’’
The keyless access system
indicator comes on and stays on
while you are driving.
The indicator comes on and stays
on in any power mode.
189
Check K eyless A ccess Syst em
Check K eyless St art ing Syst em
K eyless A ccess System
188
KEYLESS ACCESS SYSTEM
INDICATOR KEYLESS ACCESS SYSTEM
INDICATOR
\f—
—y
\fy
) \f\fy\f
y
2009 TL

In this case, you should not shut of f
your engine until you are in a saf e
location or at your dealer, as your
vehicle may not restart.The multi-inf ormation display
shows ‘‘CHECK KEYLESS
STARTING SYSTEM.’’
If the remote battery becomes
weak and the power door lock/
unlock operation is disabled.
When the keyless access remote
system main switch in the glove
box is set to of f .
In either case, you have to insert the
keyless access remote into the
keyless access remote slot to set the
power mode and start the engine. Always insert the keyless access
remote fully into the slot. To remove
it, place the vehicle in the VEHICLE
OFF (LOCK) mode, then pull out
the keyless access remote.
If the keyless access remote has
been inserted into the slot, it will
lock into place when the power is on.
The slot will unlock when the power
is turned off.
If the keyless access remote
does not come out of the slot easily,
try to push it in bef ore pulling it out.
Make sure the vehicle is in
VEHICLE OFF (LOCK) mode.
CONT INUED
K eyless A ccess System
K eyless A ccess Remote Slot
Inst rument s and Cont rols
189
NOTE:
SLOT
KEYLESS
ACCESS
REMOTE
\f—\f—y

\fy
) \f\fy\f
y
2009 TL

CONT INUED
If the vehicle is lef t in the
ACCESSORY mode, the ‘‘TO TURN
VEHICLE OFF’’ message is shown
on the multi-information display
when you open the driver’s door. If
the vehicle is lef t in the VEHICLE
OFF (LOCK) mode with the keyless
access remote in the slot, the
‘‘REMOVE KEYLESS REMOTE
FROM SLOT’’ message is shown on
the multi-information display.TheshiftlevermustbeinPark
bef ore you can press the engine
start/stop button twice without
pressing the brake pedal to set the
vehicle into the VEHICLE OFF
(LOCK) mode.
Thebuilt-inkeycanbeusedtolock/
unlock the doors and the trunk when
the remote battery becomes weak
and the power door lock/unlock
operation is disabled.
K eyless A ccess System
Built-in key and Remote
Inst rument s and Cont rols
191
\f—
—y
\fy
) \f\fy\f
y
2009 TL

To remove the built-in key, pull it out
while pressing the release button. To
reinstall the built-in key, push the
key into the remote until it clicks.
To avoid damaging the remote and
the built-in key, never pull on the
built-in key unless you are pressing
the release button.The keyless access system uses an
electric f ield to identif y the remote.
If you use medical equipment such
as a cardiac pacemaker, ask your
doctor if the electric f ield used by
the remote will af f ect it.
The trunk and glove box cannot be
opened when you turn the trunk
main switch of f and lock the glove
box and trunk pass-through cover
with the built-in key. Then, the trunk
cannot be opened by using the
remote or the exterior trunk release
switch.
Remove the built-in key from the
remote by pressing the button, then
give that remote to someone else as
a valet key.
Valet Function
K eyless A ccess System
192
RELEASE BUTTONBUILT-IN KEY
\f—\f—y

\fy
) \f\fy\f
y
2009 TL