2009 Acura RL Owner's Manual

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Turn on the headlights to test the
new bulb.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Push the bulb in slightly, and turn
it counterclockwise.
Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ).
Reinstall the engine compartment
side cover.
(Driver’s side)
Reinstall the battery cover. 2.
1.
4.
5.
6.
7.
8.
3.
457
Lights
Replacing a Front T urn Signal
Light Bulb
470
BULB SOCKET
2009 RL

CONT INUED
Remove the left or right side
engine compartment cover (see
page ).
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working. Reinstall the engine compartment
side cover.
(Driver’s side)
Reinstall the battery cover.
(Passenger’s side)
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
windshield washer reservoir.
1.
2.
5.
6. 7.
8.
4.
457
Lights
Replacing a Front Parking/Side
Marker Bulb
Maint enance
471
2009 RL

Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. (Passenger’s side)
Reinstall the windshield washer
reservoir.
Reinstall the engine compartment
side cover.
(Driver’s side)
Reinstall the battery cover.
5.
6.
7.
8.
9.
3.
4.
Lights
ReplacingaFogLightBulb
472
SOCKET
BULB
CLIP
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
2009 RL

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the two undercover bolts
onthesideundercoverand
tighten them securely. Put the
holding clip back on the side
undercover and push on the center
until it locks (the center is f lush
with the head).
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Caref ully push up the side under
cover into the bumper.
Use a Phillips-head screwdriver to
remove the two undercover bolts,
and remove the holding clip with a
f lat-tipped screwdriver. 3.
4. 5.
6.
8.
7.
1.
2.
Lights
Maint enance
473
CLIP CONNECTOR BULB
BOLTS
2009 RL

Open the trunk lid, and remove
the lef t or right maintenance lid.
Remove the mounting nut with an
8mmwrench.Carefully pry in the top or bottom
edge of the trim with a small f lat-
tipped screwdriver, and pull the
trim straight back.
Remove the two mounting bolts
with an 8 mm wrench.
Pull the taillight assembly straight
back out of the body.Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned out bulb by
pulling it straight out of its socket.
2.
1. 3.
4.
5.6.
7.
Lights
Replacing a Rear Turn Signal
Light Bulb
474
MOUNTING NUT
MAINTENANCE LID TAIL LIGHT TRIMBOLTS
BULB
SOCKET
2009 RL

Install the new bulb in the socket
by pushing it straight in the socket
until it bottoms.
Reinstall the socket into the light
assembly. Turn it clockwise to
lock it in place.
Testthelightstomakesurethe
new bulb is working.
Tighten the mounting nut securely,
and reinstall the maintenance lid.
When reinstalling the taillight
assembly, align and pop the snap
f asteners in place. Tighten the two
mounting bolts and reinstall the
trim in place.Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.
Open the trunk.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Remove the light assembly cover
by pulling its outside edge.
9.
8.
10.
11.
12. 1.
2.
3.
4.
CONT INUED
Lights
Replacing a Back-up L ight Bulb
Maint enance
475
COVERS
BULB
SOCKET
2009 RL

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
This f ilter removes the dust and
pollenthatisbroughtinfromthe
outside through the climate control
system.
Have your dealer replace the filter
when this service is indicated by a
maintenance message on the multi-
inf ormation display. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban
areas that have high concentrations
of soot in the air, or if the f low f rom
theclimatecontrolsystembecomes
less than usual.
Reinstall the socket into the light
assembly. Turn it clockwise to
lock it in place.
Testthelightstomakesurethe
new bulb is working.
Reinstall the back-up light cover.
5.
6.
7. Cleaning the Seat Belts
Dust and Pollen Filter
Lights, Dust and Pollen Filter, Cleaning the Seat Belts
476
LOOP
2009 RL

The floor mats that came with your
vehicle hook over the f loor mat
anchors. To lock each anchor, turn
theknobclockwise.Thiskeepsthe
f loor mats f rom sliding f orward
(possibly interf ering with the pedals),
or backwards (making the f ront
passenger’s weight sensors
inef f ective).
If you remove a f loor mat, make sure
tore-anchoritwhenyouputitback
in your vehicle.Make sure the rear f loor mats are
properly hooked to the f loor mat
anchors. Your vehicle is equipped
with front passenger’s seat weight
sensors. If the rear passenger’s f loor
mat is on the seat rail of the front
passenger’s seat, the sensors will
detect the decreased weight on the
seat, and they may not work properly.
If you use a non-Acura f loor mat,
make sure it f its properly and that it
canbeusedwiththefloormat
anchors. Do not put additional f loor
mats on top of the anchored mats.
Floor Mat s
Maint enance
477
DRIVER’S SIDE FLOOR MAT REAR PASSENGER’S FLOOR MAT
UnlockLock Unlock
Lock
ANCHORS ANCHOR
2009 RL