2009.5 Citroen C5 display
[x] Cancel search: displayPage 52 of 314
III
53
C O M F O R T
When starting with the engine
c o l d , a i r fl o w w i l l r e a c h i t s o p t i -
mum level gradually to prevent an
excessive distribution of cold air.
When entering the vehicle after it
has been parked for a fairly long
period, if the interior temperature
is very different from your comfort
setting there is no need to change
the temperature displayed in or-
der to quickly reach the level of
comfort required. The system
automatically uses its maximum
performance to correct the differ-
ence in temperature as quickly as
possible.
The water resulting from the air
conditioning condensation is dis-
charged via an opening provided
for this purpose; therefore, a pud-
dle of water may form underneath
the vehicle when stationary.
In all seasons, if the weather is
cool, the air conditioning is use-
ful as it removes the humidity
from the air and the condensa-
tion. Avoid driving for prolonged
periods with the air conditioning
switched off.
9. Front demisting - defrosting
In certain cases, the
"AUTO" mode may not
b e s u f fi c i e n t t o d e m i s t o r
defrost the windows (hu-
midity, several passen-
gers, ice).
Press control 9 to clear the win-
dows quickly. The indicator lamp
comes on.
This system controls the temperature,
a i r fl o w a n d i n t a k e a n d d i s t r i b u t e s t h e
ventilation to the windscreen and front
side windows.
Resuming manual control exits from
the "Demisting" mode. It must be
cancelled as soon as possible to
permit renewal of the air in the pas-
senger compartment and demisting.
Pressing one of the controls 1a and
1b returns the system to the "AUTO"
mode.
8. Rear demisting - defrosting
Switch off the rear screen and exterior
mirrors demisting when you consider
this necessary as low current con-
sumption reduces fuel consumption.
The heated rear screen
operates independently
of the air conditioning
system.
Press control 8 , with the en-
gine running, to demist the rear
screen and the mirrors. The indi-
cator lamp comes on.
Demisting is switched off automati-
cally to avoid excessive consump-
tion of current and depending on the
exterior temperature.
It may be stopped by pressing con-
trol 8 again or when the engine is
switched off.
In this latter case, the demisting re-
sumes if the engine is switched on
again within one minute.
Page 53 of 314
III
54
C O M F O R T
PROGRAMMABLE HEATING
The programmable heating operates
independently of the engine.
When the engine is off, it pre-heats
t h e c o o l a n t c i r c u i t i n o r d e r t o b e n e fi t
from an optimum engine operating
temperature from the time the en-
gine is switched on.
The programmable heating system
is switched on using the long range
remote control. Activation can be im-
mediate or deferred by means of a
programming function. Programming remote control
The heating system programming
remote control consists of the fol-
lowing buttons and displays:
1. Scrolling functions menu buttons.
2. Function indicator lights: clock,
temperature, operating time, pro-
grammed time, heater operation,
heating management symbols.
3. Digital displays: time, tempera-
ture, duration of operation, pro-
grammed time or level of heating.
4. Off button.
5. On button.
Displays on the remote
control screen Press the buttons
1 in succession to
display the functions.
T h e fi r s t p r e s s o f t h e l e f t - h a n d o r
right-hand button displays the time.
Next, the left-hand button permits ac-
cess to the programming time then to
the level of heating (C1 to C5).
The right-hand button permits ac-
cess to the passenger compartment
temperature then to the duration of
operation of the heater if it is to be
switched on immediately.
If a malfunction of the program-
mable heating system occurs,
contact a CITROËN dealer. Displaying the functions
The passenger compartment tem-
perature information is only avail-
able when the engine is off.
Page 54 of 314
III
55
C O M F O R T
Setting the time
Once the time has been displayed,
by means of the buttons 1 , press
buttons 4 and 5 simultaneously within 10 seconds. Immediate activation
Press button
5 (ON) until the mes-
sage "OK" appears.
When the signal has been received,
the message "OK" is displayed
along with the duration of operation. Press the buttons
1 to display the
duration of operation.
T h i s s y m b o l fl a s h e s .
Set the time using the buttons 1 .
Press buttons 4 and 5 simultane-
ously to save it.
T h i s s y m b o l i s d i s p l a y e d ( fi x e d ) .
The heater starts and this
symbol is displayed.
To deactivate the function, press
button 4 (OFF) until the message
"OK" appears.
This symbol is switched off.
When carrying out these opera-
tions, if the message "FAIL" ap-
pears, the signal has not been
received. Repeat the procedure
after changing your location. Setting the duration of
operation
This symbol is displayed.
Once the duration of operation has
been displayed, press buttons 4 and
5 simultaneously within 10 seconds.
T h i s s y m b o l fl a s h e s .
Set the duration by pressing the but-
tons 1 (adjustment in steps of 10 mins
and max value 30 mins).
Press buttons 4 and 5 simultaneously
to save the duration of operation.
T h i s s y m b o l i s d i s p l a y e d ( fi x e d ) .
The factory setting value is 30 minutes.
Page 55 of 314
III
56
C O M F O R T
Programming the heating
You must programme your depar-
ture time in order for the system to
calculate the optimum heater start
time automatically.
Programming the departure time
Press the buttons 1 to display the
programming time. Activation - deactivation
Once the programming time has
been displayed by means of the but-
tons
1 , press button 5 (ON) until the
message "OK" appears.
This symbol is displayed.
Once the programming time has
been displayed, press buttons 4 and
5 simultaneously within 10 seconds.
T h i s s y m b o l fl a s h e s .
Set the time by pressing the buttons 1
and press buttons 4 and 5 simultane-
ously to save it.
T h i s s y m b o l i s d i s p l a y e d ( fi x e d ) .
This symbol is displayed when
the heater starts.
HTM: Heat Thermo Management.
When the signal has been re-
ceived, the message "OK" is
displayed along with the symbol
"HTM" .
To deactivate the programming, press
button 4 (OFF) until the message
"OK" appears.
The symbol "HTM" is switched off.
When carrying out these operations,
if the message "FAIL" appears,
the signal has not been received.
Repeat the procedure after chang-
ing your location.
Switching off the heating
Press button 5 (ON).
The symbol "HTM" remains on.
Changing the level of heating
The system offers 5 levels of heat-
ing (from the lowest level C1 to the
highest level C5 ).
Once the level of heating has been
displayed by means of the buttons 1 ,
press buttons 4 and 5 simultaneously.
The letter "C" fl a s h e s .
Set the level of heating by pressing
the buttons 1 .
Press buttons 4 and 5 simultane-
ously to save the level selected. The
letter "C" i s d i s p l a y e d ( fi x e d ) .
The factory pre-sets are replaced
by the new settings entered. The
programmed times are stored until
the next time they are changed.
When the departure time is acti-
vated, the level of heating cannot
be changed. The departure time
m u s t b e d e a c t i v a t e d fi r s t .
Page 56 of 314
III
!
57
C O M F O R T
Changing the battery
The remote control is supplied by a
6 V-28L battery, which is supplied.
Information on the display indicates
when it is time to replace this battery.
Unclip the casing then replace the
battery.
The remote control must then be re-
initialised, see below. Always switch off the program-
m a b l e h e a t i n g w h i l e fi l l i n g w i t h
f u e l t o a v o i d a n y r i s k o f fi r e o r e x -
plosion.
To avoid any risk of poisoning and
asphyxiation, the programmable
heating must not be used, even
for short periods, in an enclosed
space such as a garage or work-
shop which is not equipped with an
exhaust gas extraction system.
Do not park the vehicle on an
i n fl a m m a b l e s u r f a c e ( d r y g r a s s ,
dead leaves, paper…), there is a
r i s k o f fi r e .
The programmable heating sys-
tem is supplied by the vehicle's fuel
tank. Before use, ensure that the
q u a n t i t y o f f u e l r e m a i n i n g i s s u f fi -
cient. If the fuel tank is at the re-
serve, we strongly advise that you
do not programme the heating.
Do not discard the used bat-
teries, take them to an ap-
proved collection point.
Reinitialising the remote control
If the vehicle's battery is disconnect-
ed or the remote control's battery is
replaced, the remote control must
be reinitialised.
After switching on the power, press
button 4 (OFF) for 1 second within
the next 5 seconds. If the operation
has taken place correctly the mes-
sage "OK" is displayed on the re-
mote control screen.
If a problem occurs, the message
"FAIL" appears. Repeat the operation.
In addition, your programmable
heating can be used to pre-heat
your vehicle’s passenger com-
partment. The interior volumetric protection
alarm movement sensor may be
d i s t u r b e d b y t h e fl o w o f a i r f r o m
the programmable heating when
it is in operation.
To avoid any unexpected trigger-
ing of the alarm during use of the
programmable heating, it is ad-
visable to deactivate the interior
volumetric protection.
Page 87 of 314
V
84
V I S I B I L I T Y
EXTERIOR LIGHTING CONTROLS
Control stalk for the selection and con-
trol of the various front and rear lamps
providing the vehicle's lighting.
Main lighting
The various front and rear lamps of
the vehicle are designed to adapt
the driver's visibility progressively in
relation to the climatic conditions:
- sidelamps, to be seen,
- dipped beam headlamps to see without dazzling other drivers,
- main beam headlamps to see clearly when the road is clear.
Additional lighting
O t h e r l a m p s a r e fi t t e d t o f u l fi l t h e r e -
quirements of particular driving con-
ditions:
- a rear foglamp to be seen from a distance,
- front foglamps for even better forward vision,
- directional headlamps for im- proved visibility when cornering,
- daytime running lamps to be seen during the day. Programming
Various automatic lighting control
modes are also available depending
on options:
- guide-me-home lighting,
- automatic lighting,
- directional lighting.
Manual controls
lamps off,
automatic illumination of
headlamps,
sidelamps only,
dipped headlamps or
main beam headlamps.
B. Stalk for switching headlamps by
pulling: dipped headlamps/main
beam headlamps.
In the lamps off and sidelamps
modes, the driver can switch on the
main beam headlamps temporarily
( " h e a d l a m p fl a s h " ) b y m a i n t a i n i n g a
pull on the stalk.
Displays
Lighting of the corresponding indi-
cator lamp on the instrument panel
c o n fi r m s t h e s e l e c t i v e s w i t c h i n g o n
of the lighting selected.
The lighting commands are issued
directly by the driver by means of
the ring A and the stalk B .
A. Main lighting mode selection ring,
with:
In some climatic conditions (e.g.
l o w t e m p e r a t u r e o r h u m i d i t y ) , t h e
presence of misting on the inter-
nal surface of the glass of the
headlamps and rear lamps is nor-
mal; it disappears after the lamps
have been on for a few minutes.
Page 128 of 314
VIII
112
S A F E T Y
TYRE UNDER-INFLATION DETECTION
S y s t e m w h i c h a u t o m a t i c a l l y c h e c k s t h e
p r e s s u r e s o f t h e t y r e s w h i l e d r i v i n g . Tyres OK display
Choice of detection
T h i s f u n c t i o n p r o v i d e s w a r n i n g o f t y r e s
t h a t a r e u n d e r - i n fl a t e d o r p u n c t u r e d .
Automatic detection
S e n s o r s m o n i t o r t h e t y r e p r e s s u r e s .
I n t h e e v e n t o f a n a n o m a l y , a m e s -
s a g e w i l l a p p e a r o n t h e i n s t r u m e n t
panel screen.
Driver request detection
Y o u c a n c h e c k t h e t y r e p r e s s u r e s a t
a n y t i m e .
P r e s s o n b u t t o n A (CHECK); the
i n f o r m a t i o n w i l l b e d i s p l a y e d o n
t h e i n s t r u m e n t p a n e l s c r e e n .
P r e s s o n b u t t o n A (CHECK).
T h e s y s t e m i n d i c a t e s t o y o u t h a t t h e
t y r e s a r e c o r r e c t l y i n fl a t e d .
T h i s i n f o r m a t i o n i s o n l y a v a i l a b l e o n
t h e r e q u e s t b y t h e d r i v e r . Under-inflated tyre
automatic detection
detection on request
Automatic detection:
A m e s s a g e i n d i c a t e s w h i c h t y r e i s
u n d e r - i n fl a t e d .
Driver request detection:
T h e v e h i c l e o u t l i n e i n d i c a t e s t h e u n d e r -
i n fl a t e d t y r e ( s ) .
T h e m e s s a g e i s a c c o m p a n i e d b y
lighting of the SERVICE warning
l a m p a n d a n a u d i b l e b e e p .
C h e c k t h e t y r e p r e s s u r e s a s
soon as possible.
Page 137 of 314
VIII
1 2 0
S A F E T Y
Front airbags
S y s t e m w h i c h p r o t e c t s t h e h e a d a n d
chest of the driver and front passen-
g e r i n t h e e v e n t o f a f r o n t i m p a c t .
T h e d r i v e r ' s a i r b a g i s i n c o r p o r a t e d
in the centre of the steering wheel;
t h e f r o n t p a s s e n g e r ' s a i r b a g i s i n c o r -
porated in the dashboard above the
g l o v e b o x .
Activation
T h e a i r b a g s a r e t r i g g e r e d s i m u l t a n e -
o u s l y , u n l e s s t h e p a s s e n g e r ' s f r o n t
airbag is deactivated, in the event of
a s e r i o u s f r o n t i m p a c t t o a l l o r p a r t o f
t h e f r o n t i m p a c t z o n e A , in the lon-
g i t u d i n a l c e n t r e l i n e o f t h e v e h i c l e o n
a h o r i z o n t a l p l a n e a n d d i r e c t e d f r o m
the front to the rear of the vehicle.
T h e f r o n t a i r b a g i n fl a t e s b e t w e e n t h e
f r o n t o c c u p a n t o f t h e v e h i c l e a n d t h e
d a s h b o a r d t o c u s h i o n t h e i r f o r w a r d
m o v e m e n t . Deactivation
T h i s w a r n i n g l a m p c o m e s o n
on the roof console display
w h e n t h e i g n i t i o n i s o n a n d u n -
til the air bag is reactivated.
T o g u a r a n t e e t h e s a f e t y o f y o u r
c h i l d , i t i s i m p e r a t i v e t h a t t h e p a s -
senger airbag is deactivated when
y o u i n s t a l l a " r e a r w a r d s - f a c i n g " c h i l d
seat on the front passenger seat.
O t h e r w i s e , t h e c h i l d w o u l d r i s k b e -
i n g s e r i o u s l y i n j u r e d o r k i l l e d i f t h e
airbag were triggered. Activation
W h e n y o u r e m o v e t h e c h i l d s e a t , t u r n
switch
1 to the "ON" position to re-
a c t i v a t e t h e a i r b a g a n d s o g u a r a n t e e
t h e s a f e t y o f y o u r f r o n t p a s s e n g e r i n
t h e e v e n t o f a n i m p a c t .
Operating fault
I f t h i s s y m b o l a p p e a r s o n
t h e i n s t r u m e n t p a n e l s c r e e n ,
a c c o m p a n i e d b y a n a u d i b l e
w a r n i n g a n d a m e s s a g e ,
c o n t a c t a C I T R O Ë N d e a l e r t o h a v e
t h e s y s t e m c h e c k e d . T h e a i r b a g s
m a y n o l o n g e r b e t r i g g e r e d i n t h e
e v e n t o f a s e r i o u s i m p a c t .
O n l y t h e f r o n t p a s s e n g e r ' s a i r b a g
can be deactivated:
with the ignition off , insert the
key in the passenger airbag de-
activation switch 1 ,
t u r n i t t o t h e "OFF" position,
t h e n , r e m o v e t h e k e y k e e p i n g
the switch in this position. I f t h i s w a r n i n g l a m p fl a s h e s ,
c o n t a c t a C I T R O Ë N d e a l e r .
I f b o t h a i r b a g w a r n i n g l a m p s c o m e
o n c o n t i n u o u s l y , d o n o t i n s t a l l a
"rearwards-facing" child seat on
the front passenger seat.
H a v e i t c h e c k e d b y a C I T R O Ë N
dealer.