2009.5 Citroen C3 PICASSO audio
[x] Cancel search: audioPage 16 of 198
30
MULTIFUNCTION SCREENS
MONOCHROME SCREEN A Controls
Displays on the screen
This displays the following information:
- time,
- date,
- a m b i e n t t e m p e r a t u r e ( t h i s fl a s h e s i f there is a risk of ice),
- state of the openings (doors, boot, ...),
- audio sources (radio, CD, ...),
- trip computer (refer to the end of the section).
Warning messages or information mes-
sages may appear temporarily. These
can be cleared by pressing the "ESC"
button. Main menu
Press the "MENU" button for access
to the main
menu , then press the
" " or " " buttons to scroll through
the various menus:
- radio-CD,
- v e h i c l e c o n fi g u r a t i o n ,
- options,
- display settings,
- language,
- units.
Press the "OK" button to select the
menu required.
From the audio equipment control panel,
you can:
press the "MENU" button for access
to the main
menu ,
press the " " or " " buttons to scroll
through the items on the screen,
press the "MODE" button to change
the permanent application (trip com-
puter, audio source, ...),
press the " " or " " buttons to
change a setting value,
press the "OK" b u t t o n t o c o n fi r m ,
or
press the "ESC" button to abandon
the operation in progress. Radio-CD
With the audio equipment switched on,
once the "Radio-CD" menu has been
selected you can activate or deactivate
the functions linked with use of the radio
( R D S , R E G ) o r t h e C D ( i n t r o s c a n , s h u f fl e ,
CD repeat).
For more information on the "Radio-CD"
application, refer to the Audio system part
of the "Audio and Telematics" section.
Page 19 of 198
i
i
!
!
33
MULTIFUNCTION SCREENS
Options
Once the "Options" menu has been se-
lected, you can start diagnostics of the
status of the equipment (active, not active,
faulty).
Language
Once the "Language" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:
- temperature (°C or °F),
- fuel consumption (l/100 km, mpg or km/l).
Displays on MyWay satellite navigation colour screen
"SETUP" menu
Date and time
This menu allows you to adjust the date
and time, and their format (refer to the
"Audio and telematics section").
Display
This menu allows you to adjust the
brightness of the display, the display
contrast and the colour of the map (day/
night and auto mode).
System parameters
This menu allows you to restore the
factory settings, to display the software
version and to activate scrolling text.
This displays the following information:
- time,
- date,
- audio functions,
- guidance system information.
The chosen language will also be
used on the MyWay satellite navi-
gation colour screen.
Once the fuel consumption unit
has been changed to l/100 km or
km/l, the information relating to
speed and distance also changes
to kilometres.
F o r s a f e t y r e a s o n s , c o n fi g u r a t i o n
of the multifunction screen by the
driver must only be done when
stationary. F o r s a f e t y r e a s o n s , c o n fi g u r a t i o n
of the multifunction screen by the
driver must only be done when
stationary.
Press the SETUP button to access the
"SETUP" menu. It gives you access to
the following functions:
- Date and time,
- Display,
- System parameters.
Page 20 of 198
34
MULTIFUNCTION SCREENS
Displays on the screen
This displays the following information:
- time,
- date,
- a m b i e n t t e m p e r a t u r e ( t h i s fl a s h e s i f there is a risk of ice),
- state of the openings (doors, boot, etc.),
- audio sources (radio, CD, USB socket, etc.),
- trip computer (refer to the end of the section).
Warning messages or information mes-
sages may appear temporarily. These
can be cleared by pressing the "ESC"
button. From the audio equipment control pan-
el, you can:
press the "MENU" button to gain
access to the main
menu ,
press the " " or " " buttons to scroll
through the items on the screen,
press the "MODE" button to change
the permanent application (trip com-
puter, audio source, ...),
press the " " or " " buttons to
change a setting value,
press the "OK" b u t t o n t o c o n fi r m ,
or
press the "ESC" button to abandon
the operation in progress. Main menu
Press the "MENU" button to gain
access to the main
menu :
- audio functions,
- the trip computer (refer to the end of the section),
- p e r s o n a l i s a t i o n - c o n fi g u r a t i o n ,
Press the " " or " " buttons to se-
l e c t t h e m e n u r e q u i r e d , t h e n c o n fi r m
by pressing the "OK" button.
MONOCHROME SCREEN C Controls
"Audio functions" menu
With the audio equipment switched on,
once this menu has been selected you
can activate or deactivate the functions
linked with use of the radio (RDS, REG,
R a d i o T e x t ) , t h e C D ( i n t r o s c a n , s h u f fl e ,
CD repeat) or the MP3 player (USB
port).
For more information on the "Audio
functions" application, refer to the Audio
systems part of the "Audio and Telemat-
ics" section.
Page 135 of 198
132
PRACTICAL INFORMATION
Fuse N° Rating Functions
F8 20 A Multifunction screen, audio system, navigation radio.
F9 30 A A u d i o s y s t e m ( fi t t e d a s a n o p t i o n ) , 1 2 V s o c k e t .
F10 15 A Steering mounted controls.
F11 15 A Ignition, diagnostic socket.
F12 15 A Rain/brightness sensor, trailer relay unit.
F13 5 A Main stop switch, engine relay unit.
F14 15 A Parking sensor control unit, seat belt unfastened
warning lamp, airbag control unit, instrument panel,
a i r c o n d i t i o n i n g , U S B B o x .
F15 30 A Locking.
F16 - Not used.
F17 40 A R e a r s c r e e n a n d e x t e r i o r m i r r o r s d e m i s t / d e f r o s t .
SH - PARC shunt.
Page 142 of 198
i
!
138
PRACTICAL INFORMATION A fl a t b a t t e r y p r e v e n t s t h e e n g i n e
from starting (refer to the corre-
s p o n d i n g p a r a g r a p h ) .
If the telephone is being used at
the same time on the MyWay audio
navigation system, it will be inter-
rupted after 10 minutes.
ENERGY ECONOMY MODE
System which manages the period of
use of certain functions to conserve a
s u f fi c i e n t l e v e l o f c h a r g e i n t h e b a t t e r y .
After the engine has stopped, you can
still use functions such as the audio
e q u i p m e n t , w i n d s c r e e n w i p e r s , d i p p e d
beam headlamps, courtesy lamps, etc.
f o r a m a x i m u m c o m b i n e d p e r i o d o f
thirty minutes.
This period may be greatly reduced if
the battery is not fully charged. Exiting economy mode
These functions are reactivated auto-
m a t i c a l l y t h e n e x t t i m e t h e v e h i c l e i s
driven.
In order to resume the use of these
functions immediately, start the en-
gine and let it run for a few minutes.
The time available to you will then be dou-
ble the period for which the engine is left
running. However, this period will always
b e b e t w e e n fi v e a n d t h i r t y m i n u t e s .
Switching to economy mode
Once this period has elapsed, a mes-
sage appears on the multifunction
screen indicating that the vehicle has
switched to economy mode and the
active functions are put on standby.
CHANGING A FRONT OR REAR WIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
of tools.
Removal
Raise the corresponding wiper arm.
Unclip the wiper blade and remove it.
Fitting
At the front, check the size of the wiper
b l a d e a s t h e s h o r t e r b l a d e i s fi t t e d t o
the passenger side of the vehicle.
Put the corresponding new wiper
blade in place and clip it.
Fold down the wiper arm carefully.
Before removing a front wiper
blade
Within one minute after switching off
the ignition, operate the wiper stalk
to position the wiper blades in the
vertical position.
This position must be used in order to avoid
damaging the wiper blade and the bonnet.
After fitting a front wiper blade
Switch on the ignition.
Operate the wiper stalk again to
park the wiper blades.
Page 146 of 198
i
!
142
PRACTICAL INFORMATION
ACCESSORIES
You can obtain a wide range of accessories and genuine parts from the CITROËN
dealer network.
T h e y a l l b e n e fi t f r o m t h e C I T R O Ë N w a r r a n t y a n d r e c o m m e n d a t i o n .
These accessories and parts, having been tested and approved f or reliability and
safety, are all adapted to your CITROËN vehicle.
T h e p r o d u c t r a n g e i s s t r u c t u r e d a r o u n d 5 c a t e g o r i e s :
"Styling":
seat covers, 15, 16 and 17 inch alloy
wheels, wheel embellishers, styling
strips...
"Protection":
a n t i - t h e f t a l a r m , fi r s t a i d k i t , w a r n i n g t r i -
angle, high visibility jacket, snow chains
and non-slip covers, front foglamp kit,
parking assistance system...
* To avoid any risk of jamming of the p e d a l s :
- ensure that the mat is positioned and secured correctly,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
"In-car technology":
Bluetooth
®
hands free kit, audio sys-
tems, portable navigation system,
a u x i l i a r y a u d i o c a b l e ( e . g . f o r a n M P 3
c o n n e c t i o n ) , l o u d s p e a k e r s , U S B B o x ,
portable video screen...
"Comfort and Leisure":
mats * , boot tray, sun blinds, roof bars,
towbar, bicycle carrier, ski carrier, dog
guard, luggage net, booster seats and
child seats... "Universal":
s c r e e n w a s h fl u i d , m a i n t e n a n c e a n d c l e a n -
i n g p r o d u c t s f o r i n t e r i o r a n d e x t e r i o r .
Depending on the country in which
the vehicle is sold, it is compulso-
ry to have a high visibilty jacket,
warning triangle and spare bulbs
available in the vehicle.
T h e fi t t i n g o f e l e c t r i c a l e q u i p m e n t o r
accessories which are not recom-
mended by CITROËN may result
in a failure of your vehicle's elec-
t r o n i c s y s t e m a n d e x c e s s i v e p o w e r
consumption.
P l e a s e t a k e n o t e o f t h i s s p e c i fi c
warning. You are advised to contact
your dealer to be shown the range
o f r e c o m m e n d e d e q u i p m e n t a n d
accessories.
Page 159 of 198
155
0 3
4
3
2
1
7
6
5
N A V I G A T I O N - G U I D A N C E
R O U T E O P T I O N S
Select the "Route dynamics" function. T h i s f u n c t i o n g i v e s a c c e s s t o t h e " T r a f fi c i n d e p e n d e n t " o r " S e m i -dynamic" options.
Select the "Avoidance criteria" function. This function provides a c c e s s t o t h e A V O I D o p t i o n s ( m o t o r w a y s , t o l l r o a d s , f e r r i e s ) .
Turn the dial and select the "Recalculate" function to take into account the route options selected. P r e s s t h e d i a l t o c o n fi r m .
Press the NAV button.
P r e s s t h e N A V b u t t o n a g a i n o r s e l e c t t h e N a v i g a t i o n M e n u f u n c t i o n a n d p r e s s t h e d i a l t o c o n fi r m .
Select the "Route type" function and p r e s s t h e d i a l t o c o n fi r m . T h i s f u n c t i o n a l l o w s y o u t o c h a n g e t h e r o u t e t y p e .
Select the "Route options" function a n d p r e s s t h e d i a l t o c o n fi r m .
R E C A L C U L A T E
A V O I D A N C E C R I T E R I A
R O U T E D Y N A M I C S
R O U T E T Y P E
R O U T E O P T I O N S
" N A V I G A T I O N " M E N U
The route selected by the MyWay audio/telephone de
pends directly on the route options. C h a n g i n g t h e s e o p t i o n s m a y c h a n g e t h e r o u t e c o m p l e t e l y .
Page 165 of 198
161
0 4
2
1
3
2
1
P R I N C I P A L T M C S Y M B O L S
R e d a n d y e l l o w t r i a n g l e : t r a f fi c i n f o r m a t i o n , p a r
e x a m p l e :
B l a c k a n d b l u e t r i a n g l e : g e n e r a l i n f o r m a t i o n , f o r e x a m p l e :
With the current audio source displayed on the screen, press the dial.
T h e s h o r t c u t m e n u f o r t h e s o u r c e a p p e a r s a n d g i v e s a c c e s s t o : T h e s h o r t c u t m e n u f o r t h e s o u r c e a p p e a r s a n d g i v e s a c c e s s t o :
S e l e c t T r a f fi c A n n o u n c e m e n t s ( T A ) a n d p r e s s t h e d i a l t o c o n fi r m a n d g o t o t h e a s s o c i a t e d s e t t i n g s .
T h e T A ( T r a f fi c A n n o u n c e m e n t ) f u n c t i o n g i v e s p r i o r i t y t o T A a l e r t m e s s a g e s . T o o p e r a t e , t h i s f u n c t i o n n e e d s g o o d r e c e p t i o n o f a r a d i o s t a t i o n t r a n s m i t t i n g t h i s t y p e o f m e s s a g e . W h e n a t r a f fi c r e p o r t i s t r a n s m i t t e d , t h e c u r r e n t a u d i o s o u r c e ( R a d i o , C D , J u k e b o x , . . . ) i s i n t e r r u p t e d a u t o m a t i c a l l y t o p l a y t h e T A m e s s a g e . N o r m a l p l a y b a c k of the audio source resumes at the end of the transmission of the m e s s a g e .
R E C E I V I N G T A M E S S A G E S
TA