2008 YAMAHA TZR50 warning light

SAFETY INFORMATION.....................1-1
DESCRIPTION.....................................2-1
Left view ...........................................2-1
Right view .........................................2-2
Controls and instruments .................2-3
INSTRUMENT AND CONTROL
FUNCTIONS........................................3-1
Main switch/steering lock .................3-1
Indicator and warning lights .............3-1
Speedometer unit .............................3-2
Tachometer .......................................3-3
Handlebar switches ..........................3-3
Clutch lever .......................................3-4
Shift pedal.........................................3-4
Brake lever ........................................3-5
Brake pedal.......................................3-5
Fuel ...................................................3-5
Catalytic converter............................3-6
Fuel tank cap ....................................3-6
Fuel tank breather/overflow hose .....3-7
2-stroke engine oil ............................3-7
Fuel cock ..........................................3-8
Starter (choke) lever “
q” .................3-8
Seat...................................................3-9
Anti-theft device housing..................3-9
Rear view mirrors ..............................3-9
Sidestand ........................................3-10
Ignition circuit cut-off system .........3-10PRE-OPERATION CHECKS...............4-1
Pre-operation check list....................4-2
OPERATION AND IMPORTANT RIDING
POINTS................................................5-1
Starting a cold engine ......................5-1
Starting a warm engine ....................5-2
Shifting ..............................................5-2
Tips for reducing fuel consumption..5-3
Engine break-in.................................5-3
Parking ..............................................5-4
PERIODIC MAINTENANCE AND
MINOR REPAIR...................................6-1
Owner’s tool kit .................................6-1
Periodic maintenance and
lubrication chart ............................6-2
Removing and installing cowlings
and panels .....................................6-5
Checking the spark plug ..................6-7
Transmission oil ................................6-8
Coolant .............................................6-9
Air filter element ..............................6-12
Adjusting the carburetor .................6-12
Adjusting the throttle cable free
play ..............................................6-12
Adjusting the engine idling speed ..6-13
Tires ................................................6-14
Cast wheels ....................................6-16
Adjusting the clutch lever free
play ..............................................6-16Checking the front brake lever free
play ..............................................6-17
Adjusting the brake pedal free
play ..............................................6-17
Adjusting the shift pedal position ...6-18
Adjusting the rear brake light
switch ..........................................6-18
Checking the front and rear brake
pads.............................................6-18
Checking the brake fluid level ........6-19
Changing the brake fluid ................6-20
Drive chain slack.............................6-21
Cleaning and lubricating the drive
chain ............................................6-22
Checking and lubricating the
cables ..........................................6-23
Checking and lubricating the
throttle grip and cable .................6-23
Adjusting the Autolube pump .........6-24
Checking and lubricating the brake
and shift pedals ...........................6-24
Checking and lubricating the brake
and clutch levers .........................6-24
Checking and lubricating the
sidestand .....................................6-25
Checking the front fork ...................6-25
Checking the steering.....................6-26
Checking the wheel bearings .........6-26
Battery ............................................6-27
Replacing the fuse ..........................6-28
Replacing the headlight bulb..........6-28
TABLE OF CONTENTS
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 6

EAU10460
Main switch/steering lock
The main switch/steering lock con-
trols the ignition and lighting systems,
and is used to lock the steering. The
various positions are described
below.
EAU10640
f
All electrical circuits are supplied with
power, and the engine can be started.
The key cannot be removed.
NOTE:
The headlight, meter lighting and tai-
llight come on automatically when the
engine is started.
EAU10660
e
All electrical systems are off. The key
can be removed.
EAU10680
m
The steering is locked, and all electri-
cal systems are off. The key can be
removed.
T
o lock the steering
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “
e”
position, and then turn it to “
m”
while still pushing it.
3. Remove the key.
T
o unlock the steering
Push the key in, and then turn it to
“
e” while still pushing it.EWA10060
s s
WARNING
Never turn the key to “
e” or “m”
while the vehicle is moving, other-
wise the electrical systems will be
switched off, which may result in
loss of control or an accident.
Make sure that the vehicle is stop-
ped before turning the key to “
e”
or “
m”.
EAU11003
Indicator and warning lights
1. Coolant temperature warning light “y”
2. Oil level warning light “z”
3. Neutral indicator light “N”
4. Engine trouble warning light “ ”
5. Turn signal indicator light “
b”
EAU11020
Turn signal indicator light “cd”
This indicator light flashes when the
turn signal switch is pushed to the left
or right.
EAU11060
Neutral indicator light “N”
This indicator light comes on when
the transmission is in the neutral posi-
tion.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-1
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 1

EAU11440
Coolant temperature warning light
“
y”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and
allow the engine to cool.
The electrical circuit of the warning
light can be checked by turning the
key to “
f”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical
circuit.
ECA10020
CAUTION:
Do not operate the engine if it is
overheated.
EAUM1061
Oil level warning light “z”
This warning light comes on when the
key is in the “
f” position or when the
oil level in the 2-stroke engine oil tank
is low during operation. If the warning
light comes on during operation, stop
immediately and fill the oil tank with
2-stroke engine oil of either JASO
grade “FC” or ISO grades “EG-C” or
“EG-D”. The warning light should gooff after the 2-stroke engine oil tank
has been refilled.
NOTE:
If the warning light does not come on
when the key is in the “
f” position or
does not go off after the 2-stroke
engine oil tank has been refilled, have
an Yamaha dealer check the electrical
circuit.
ECA10010
CAUTION:
Do not operate the vehicle until you
know that the engine oil level is suf-
ficient.
EAU11500
Engine trouble warning light “ ”
This warning light comes on or
flashes when an electrical circuit
monitoring the engine is defective.
When this occurs, have a Yamaha
dealer check the self-diagnosis sys-
tem.
The electrical circuit of the warning
light can be checked by turning the
key to “
f”. If the warning light does
not come on for a few seconds, then
go off, have a Yamaha dealer check
the electrical circuit.
EAU11621
Speedometer unit
1. Speedometer
2. Odometer
The speedometer unit is equipped
with a speedometer and an odometer.
The speedometer shows riding spe-
ed. The odometer shows the total dis-
tance traveled.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-2
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 2

EAU15950
EWA10270
s s
WARNING
Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer
regarding any control or func-
tion that you do not thoroughly
understand.
Never start the engine or ope-
rate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of cons-
ciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised comple-
tely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
EAU16050
Starting a cold engine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.
The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EWA10290
s s
WARNING
Before starting the engine,
check the function of the igni-
tion circuit cut-off system
according to the procedure
described on page 3-11.
Never ride with the sidestand
down.
1. Turn the fuel cock lever to “ON”.
2. Turn the key to “
f” and make
sure that the engine stop switch
is set to “
f”.
3. Shift the transmission into the
neutral position.
NOTE:
When the transmission is in the neu-
tral position, the neutral indicator lightshould be on, otherwise have a
Yamaha dealer check the electrical
circuit.
4. Turn the starter (choke) on and
completely close the throttle.
(See page 3-8.)
5. Start the engine by pushing the
start switch.
NOTE:
If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre-
serve the battery. Do not crank the
engine more than 10 seconds on any
one attempt.
ECA11410
CAUTION:
The 2-stroke engine oil level war-
ning light should come on when the
start switch is pushed, and it
should go off when the start switch
is released. If the warning light flic-
kers or remains on after starting,
immediately stop the engine, and
then check the 2-stroke engine oil
level and the vehicle for oil leakage.
5
OPERATION AND IMPORTANT RIDING POINTS
5-1
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 1

If necessary, add 2-stroke engine
oil, and then check the warning
light again. If the warning light does
not come on when pushing the
start switch, or if it does not go off
after starting with sufficient 2-stro-
ke engine oil, have a Yamaha dealer
check the electrical circuit.
6. After starting the engine, move
the starter (choke) back halfway.
ECA11040
CAUTION:
For maximum engine life, never
accelerate hard when the engine is
cold!
7. When the engine is warm, turn
the starter (choke) off.
NOTE:
The engine is warm when it responds
normally to the throttle with the starter
(choke) turned off.
EAU16640
Starting a warm engine
Follow the same procedure as for
starting a cold engine with the excep-
tion that the starter (choke) is not
required when the engine is warm.
EAU16671
Shifting
1. Shift pedal
Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing
hills, etc.
The gear positions are shown in the
illustration.
NOTE:
To shift the transmission into the neu-
tral position, press the shift pedal
down repeatedly until it reaches the
end of its travel, and then slightly rai-
se it.
6
5
4
3
2
N
1
1
5
OPERATION AND IMPORTANT RIDING POINTS
5-2
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 2

NOTE:
The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
2. Check the coolant level in the
coolant reservoir.
NOTE:
The coolant should be between the
minimum and maximum level marks.
3. If the coolant is at or below the
minimum level mark, open thereservoir cap, add coolant to the
maximum level mark, and then
close the reservoir cap.
EWA10380
s s
WARNING
Never attempt to remove the radia-
tor cap when the engine is hot.
NOTE:
If the engine overheats, see page
6-33 for further instructions.
EAU20431
To change the coolant
1. Place the vehicle on the centers-
tand and let the engine cool if
necessary.
2. Remove cowlings A and B. (See
page 6-5.)
3. Place a container under the engi-
ne to collect the used coolant.
1. Radiator cap
2. Coolant drain bolt
4. Remove the radiator cap.EWA10380
s s
WARNING
Never attempt to remove the radia-
tor cap when the engine is hot.
5. Remove the coolant drain bolt to
drain the cooling system.
6. After the coolant is completely
drained, thoroughly flush the
cooling system with clean tap
water.
7. Install the coolant drain bolt, and
then tighten it to the specified
torque.
1
2
MAX
MIN
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 10

EAUT1220
Checking the front brake
lever free play
1. Brake lever free play
The brake lever free play should mea-
sure 2~5 mm (0.08~0.20 in) as shown.
Periodically check the brake lever free
play and, if necessary, have a Yamaha
dealer check the brake system.
EWA10640
s s
WARNING
An incorrect brake lever free play
indicates a hazardous condition in
the brake system. Do not operate
the motorcycle until the brake sys-
tem has been checked or repaired
by a Yamaha dealer.
EAUM1352
Adjusting the brake pedal
free play
1. Brake pedal free play
The brake pedal free play should
measure 10~15 mm (0.39~0.59 in) as
shown. Periodically check the brake
pedal free play and, if necessary, have
a Yamaha dealer adjust it.
EWAM1010
s s
WARNING
You are hereby informed that any
attempt to change the engine or
any other part to increase the sco-
oter’s performance or power is
strictly forbidden by law.
Any change resulting in an
increase of the vehicle’s maxi-
mum speed or in an increase of
the engine’s capacity entails a
category classification shift
from scooter to light motorcy-
cle, with all the consequences
relating to the latter category,
compelling the owner to:
- proceed with a new certifica-
tion,
- have the vehicle registered,
- hold a driving license (pur-
suant to the new legislation).
In addition, you are informed that
such changes will bar you from
insurance coverage insofar as
insurance policies expressly stipu-
late that such technical changes
brought with a view to enhancing
performance are forbidden.
For the above-mentioned reasons,
any violation of the rules forbidding
personal or otherwise third-party
interventions is punishable by law
with penalties (including seizure of
the vehicle) to which, as the case
may be, penalties may be added
relating to the failure to wear a
1
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 17

1. Headlight lead connectors
2. Headlight bulb holder
2. Unhook the headlight bulb hol-
der, and then remove the defecti-
ve bulb.
EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
3. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
ECA10660
CAUTION:
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be adver-
sely affected. Thoroughly clean off
any dirt and fingerprints on the
headlight bulb using a cloth mois-
tened with alcohol or thinner.
4. Connect the headlight lead con-
nectors, and then install the bulb
cover.
5. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAUS1150
Replacing the license plate
light bulb
1. Remove the lens by removing the
screw.
2. Remove the defective bulb by
pulling it out.
3. Insert a new bulb into the socket.
4. Install the lens by installing the
screw.
ECA11190
CAUTION:
Do not overtighten the screw,
otherwise the lens may break.
1
2
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-29
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 29