2008 YAMAHA JOG50R turn signal

SAFETY INFORMATION.....................1-1
Further safe-riding points .................1-4
DESCRIPTION.....................................2-1
Left view ...........................................2-1
Right view .........................................2-3
Controls and instruments .................2-5
INSTRUMENT AND CONTROL
FUNCTIONS........................................3-1
Main switch/steering lock .................3-1
Indicator and warning lights .............3-2
Speedometer ....................................3-3
Multi-function display .......................3-4
Handlebar switches ..........................3-6
Front brake lever...............................3-6
Rear brake lever................................3-7
Fuel and 2-stroke engine oil tank
caps ...............................................3-7
Fuel ...................................................3-8
Catalytic converter............................3-8
2-stroke engine oil ............................3-9
2-stroke engine oil tank ....................3-9
Kickstarter.......................................3-10
Seat.................................................3-10
Storage compartment.....................3-11
Luggage hook .................................3-12
PRE-OPERATION CHECKS...............4-1
Pre-operation check list....................4-2OPERATION AND IMPORTANT
RIDING POINTS..................................5-1
Starting a cold engine ......................5-1
Starting off ........................................5-2
Acceleration and deceleration ..........5-2
Braking..............................................5-3
Tips for reducing fuel
consumption..................................5-3
Engine break-in.................................5-4
Parking ..............................................5-4
PERIODIC MAINTENANCE AND
MINOR REPAIR...................................6-1
Periodic maintenance and
lubrication chart ............................6-2
Removing and installing the
cowling and panel .........................6-5
Checking the spark plug ..................6-6
Final transmission oil ........................6-7
Coolant (only for liquid-cooled
models) ..........................................6-8
Air filter element ................................6-9
Adjusting the carburetor .................6-10
Adjusting the throttle cable
free play .......................................6-10
Tires ................................................6-11
Cast wheels ....................................6-12
Checking the front brake lever
free play .......................................6-13
Adjusting the rear brake lever
free play .......................................6-13Checking the front brake pads
and rear brake shoes ..................6-14
Checking the brake fluid level ........6-15
Changing the brake fluid ................6-16
Checking and lubricating the
throttle grip and cable .................6-16
Lubricating the front and rear
brake levers .................................6-16
Checking and lubricanting the
centerstand .................................6-17
Checking the front fork ...................6-17
Checking the steering.....................6-18
Checking the wheel bearings .........6-19
Battery ............................................6-19
Replacing the fuse ..........................6-20
Replacing the headlight bulb
or a front turn signal light
bulb .............................................6-21
Replacing the tail/brake light
bulb or a rear turn signal light
bulb .............................................6-22
Replacing an auxiliary light
bulb .............................................6-23
Troubleshooting ..............................6-24
Troubleshooting charts ...................6-25
SCOOTER CARE AND STORAGE.....7-1
Matte color caution...........................7-1
Care ..................................................7-1
Storage .............................................7-3
TABLE OF CONTENTS
5RW-F8199-E4.QXD 19/11/07 08:01 Página 5

• Always obey the speed limit
and never travel faster than
warranted by road and traffic
conditions.
• Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
●The posture of the operator and
passenger is important for proper
control.
• The operator should keep both
hands on the handlebar and
both feet on the footboard
during operation to maintain
control of the scooter.
• The passenger should always
hold onto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
feet on the passenger footrests.
• Never carry a passenger
unless he or she can firmly pla-
ce both feet on the passenger
footrests.
●Never ride under the influence of
alcohol or other drugs.
●This scooter is designed for on-
road use only. It is not suitable for
off-road use.Protective apparel
The majority of fatalities from scooter
accidents are the result of head inju-
ries. The use of a safety helmet is the
single most critical factor in the pre-
vention or reduction of head injuries.
●Always wear an approved hel-
met.
●Wear a face shield or goggles.
Wind in your unprotected eyes
could contribute to an impair-
ment of vision which could delay
seeing a hazard.
●The use of a jacket, substantial
shoes, trousers, gloves, etc., is
effective in preventing or redu-
cing abrasions or lacerations.
●Never wear loose-fitting clothes,
otherwise they could catch on
the control levers or wheels and
cause injury or an accident.
●Never touch the engine or
exhaust system during or after
operation. They become very hot
and can cause burns. Always
wear protective clothing that
covers your legs, ankles, and
feet.
●Passengers should also observe
the above precautions.
Modifications
Modifications made to this scooter
not approved by Yamaha, or the
removal of original equipment, may
render the scooter unsafe for use and
may cause severe personal injury.
Modifications may also make your
scooter illegal to use.
Loading and accessories
Adding accessories or cargo to your
scooter can adversely affect stability
and handling if the weight distribution
of the scooter is changed. To avoid
the possibility of an accident, use
extreme caution when adding cargo
or accessories to your scooter. Use
extra care when riding a scooter that
has added cargo or accessories. Here
are some general guidelines to follow
if loading cargo or adding accessories
to your scooter:
Loading
The total weight of the operator, pas-
senger, accessories and cargo must
not exceed the maximum load limit.
1
tSAFETY INFORMATION
1-2
5RW-F8199-E4.QXD 19/11/07 08:01 Página 8

Gasoline and exhaust gas
●GASOLINE IS HIGHLY FLAMMA-
BLE:
• Always turn the engine off
when refueling.
• Take care not to spill any gaso-
line on the engine or exhaust
system when refueling.
• Never refuel while smoking or
in the vicinity of an open flame.
●Never start the engine or let it run
for any length of time in a closed
area. The exhaust fumes are poi-
sonous and may cause loss of
consciousness and death within
a short time. Always operate your
scooter in an area that has ade-
quate ventilation.
●Always turn the engine off before
leaving the scooter unattended
and remove the key from the
main switch. When parking the
scooter, note the following:
• The engine and exhaust sys-
tem may be hot, therefore,
park the scooter in a place
where pedestrians or children
are not likely to touch these hot
areas.• Do not park the scooter on a
slope or soft ground, otherwise
it may fall over.
• Do not park the scooter near a
flammable source (e.g., a kero-
sene heater, or near an open
flame), otherwise it could catch
fire.
●If you should swallow any gasoli-
ne, inhale a lot of gasoline vapor,
or allow gasoline to get into your
eyes, see your doctor immedia-
tely. If any gasoline spills on your
skin or clothing, immediately
wash the affected area with soap
and water and change your clot-
hes.
EAU10371
Further safe-riding points
●Be sure to signal clearly when
making turns.
●Braking can be extremely difficult
on a wet road. Avoid hard bra-
king, because the scooter could
slide. Apply the brakes slowly
when stopping on a wet surface.
●Slow down as you approach a
corner or turn. Once you have
completed a turn, accelerate
slowly.
●Be careful when passing parked
cars. A driver might not see you
and open a door in your path.
●Railroad crossings, streetcar
rails, iron plates on road cons-
truction sites, and manhole
covers become extremely slip-
pery when wet. Slow down and
cross them with caution. Keep
the scooter upright, otherwise it
could slide out from under you.
●The brake pads could get wet
when you wash the scooter. After
washing the scooter, check the
brakes before riding.
1
tSAFETY INFORMATION
1-4
5RW-F8199-E4.QXD 19/11/07 08:01 Página 10

EAU11003
Indicator and warning lights
For CS50/CS50M
1. Left turn signal indicator light “c”
2. Oil level warning light “z”
3. High beam indicator light “j”
4. Right turn signal indicator light “d”
For CS50Z
1. Left turn signal indicator light “c”
2. Coolant temperature warning light “y”
3. Oil level warning light “z”
4. High beam indicator light “j”
5. Right turn signal indicator light “d”
EAU11030
Turn signal indicator lights “c” and
“d”
The corresponding indicator light flas-
hes when the turn signal switch is
pushed to the left or right.
EAU11080
High beam indicator light “j”
This indicator light comes on when
the high beam of the headlight is swit-
ched on.
EAU11180
Oil level warning light “z”
This warning light comes on when the
key is in the “h” position or when the
oil level in the 2-stroke engine oil tank
is low during operation. If the warning
light comes on during operation, stop
immediately and fill the oil tank with
Yamalube 2 or equivalent 2-stroke
engine oil of either JASO grade “FC”
or ISO grades “EG-C” or “EG-D”. The
warning light should go off after the 2-
stroke engine oil tank has been refi-
lled.
NOTE:
If the warning light does not come on
when the key is in the “h” position or
does not go off after the 2-stroke
engine oil tank has been refilled, have
a Yamaha dealer check the electrical
circuit.
ECA10010
CAUTION:
Do not operate the vehicle until you
know that the engine oil level is suf-
ficient.
km/h
01020304050607080
1
2345
km/h
01020304050607080
1
234
INSTRUMENT AND CONTROL FUNCTIONS
3-2
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 18

EAU12347
Handlebar switches
1. Dimmer switch “j/k”
2. Turn signal switch “c/d”
3. Horn switch “a”
1. Start “g”
EAU12400
Dimmer switch “j/k”
Set this switch to “j” for the high
beam and to “k” for the low beam.
EAU12460
Turn signal switch “c/d”
To signal a right-hand turn, push this
switch to “d”. To signal a left-hand
turn, push this switch to “c”. When
released, the switch returns to the
center position. To cancel the turn
signal lights, push the switch in after it
has returned to the center position.
EAU12500
Horn switch “a”
Press this switch to sound the horn.
EAUM1131
Start switch “g”
Push this switch while applying the
front or rear brake to crank the engine
with the starter.
ECA10050
CAUTION:
See page 5-1 for starting instruc-
tions prior to starting the engine.
EAU12900
Front brake lever
1. Front brake lever
The front brake lever is located on the
right handlebar grip. To apply the
front brake, pull this lever toward the
handlebar grip.
1
Right
1
2
3 Left
INSTRUMENT AND CONTROL FUNCTIONS
3-6
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 22

EAU16761
Starting off
NOTE:
Before starting off, allow the engine to
warm up.
1. While pulling the rear brake lever
with your left hand and holding
the grab bar with your right hand,
push the scooter off the centers-
tand.
1. Grab bar
2. Rear brake lever
2. Sit astride the seat, and then
adjust the rear view mirrors.
3. Switch the turn signals on.4. Check for oncoming traffic, and
then slowly turn the throttle grip
(on the right) in order to take off.
5. Switch the turn signals off.
EAU16780
Acceleration and
deceleration
The speed can be adjusted by ope-
ning and closing the throttle. To incre-
ase the speed, turn the throttle grip in
direction (a). To reduce the speed,
turn the throttle grip in direction (b).
(b)
(a)
ZAUM0199
OPERATION AND IMPORTANT RIDING POINTS
5-2
5
5RW-F8199-E4.QXD 19/11/07 08:01 Página 33

EAU18740
Removing and installing the
cowling and panel
1. Cowling
1. Panel A
The cowling and panel shown above
need to be removed to perform some
of the maintenance jobs described inthis chapter. Refer to this section
each time a cowling or panel needs to
be removed and installed.
EAUT1140
Cowling A
T
o remove the cowling
1. Remove the cowling screws.
1. Cowling
2. Screw
2. Disconnect the headlight coupler,
the turn signal lead couplers, and
the auxiliary light lead coupler.
1. Headlight coupler
2. Auxiliary light lead coupler
3. Turn signal light lead coupler
3. Pull the cowling off as shown.
T
o install the cowling
1. Connect the headlight coupler,
the turn signal lead couplers, and
the auxiliary light lead coupler.
2. Place the cowling in the original
position, and then install the
screws.
PERIODIC MAINTENANCE AND MINOR REPAIR
6-5
6
5RW-F8199-E4.QXD 19/11/07 08:01 Página 40

EAUS1430
Replacing the headlight bulb
or a front turn signal light
bulb
If a bulb burns out, replace it as
follows.
ECA10670
CAUTION:
It is advisable to have a Yamaha
dealer perform this job.
Headlight bulb
1. Remove cowling A.
2. Disconnect the headlight leads,
and then unhook the headlight
bulb holder as shown.
1. Headlight couplers
2. Headlight bulb holder
3. Remove the bulb holder by
pulling it and then, remove the
defective bulb by turning it coun-
terclockwise.
1. Bulb holder
2. Push in and turn counterclockwise.
3. Remove the bulb.
4. Headlight bulb
EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
4. Insert a new headlight bulb into
the bulb holder and turn it clock-
wise.
5. Place the bulb holder in its origi-
nal position, and then secure it
with its holder as shown.
6. Connect the headlight leads and
install the cowling.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
GGYYBB
1 2
3
4
GYB
1
2
PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
6
5RW-F8199-E4.QXD 19/11/07 08:01 Página 56