Page 17 of 72
EAU10460
Main switch/steering lock
The main switch/steering lock con-
trols the ignition and lighting systems,
and is used to lock the steering. The
various positions are described
below.
EAU10640
ON “f”
All electrical circuits are supplied with
power, and the engine can be started.
The key cannot be removed.
NOTE:
The headlight, meter lighting and tai-
llight come on automatically when the
engine is started.
EAU10660
OFF “ e”
All electrical systems are off. The key
can be removed.
EAU10670
h
The 2-stroke engine oil level warning
light should come on. (See page 5-1.)
EAU10680
LOCK “ m”
The steering is locked, and all electri-
cal systems are off. The key can be
removed.
T
o lock the steering
1. Turn the handlebars all the way to the left.
1. Push
2. Turn
2. Push the key in from the “ e”
position, and then turn it to “ m”
while still pushing it.
3. Remove the key.
T
o unlock the steering
1. Push
2. Turn
Push the key in, and then turn it to
“ e ” while still pushing it.
EWA10060
s s
WARNING
Never turn the key to “ e
e
” or “ m
m
”
while the vehicle is moving, other-
wise the electrical systems will be
switched off, which may result in
loss of control or an accident.
Make sure that the vehicle is stop-
ped before turning the key to “ e e
”
or “ m
m
”.
m
INSTRUMENT AND CONTROL FUNCTIONS
3-1
3
5RW-F8199-E4.QXD 19/11/07 20:04 Página 17
Page 18 of 72
EAU11003
Indicator and warning lights
For CS50/CS50M
1. Left turn signal indicator light “c”
2. Oil level warning light “z”
3. High beam indicator light “j”
4. Right turn signal indicator light “d”
For CS50Z
1. Left turn signal indicator light “c”
2. Coolant temperature warning light “y”
3. Oil level warning light “z”
4. High beam indicator light “j”
5. Right turn signal indicator light “d”
EAU11030
Turn signal indicator lights “c” and
“d”
The corresponding indicator light flas-
hes when the turn signal switch is
pushed to the left or right.
EAU11080
High beam indicator light “j”
This indicator light comes on when
the high beam of the headlight is swit-
ched on.
EAU11180
Oil level warning light “z”
This warning light comes on when the
key is in the “h” position or when the
oil level in the 2-stroke engine oil tank
is low during operation. If the warning
light comes on during operation, stop
immediately and fill the oil tank with
Yamalube 2 or equivalent 2-stroke
engine oil of either JASO grade “FC”
or ISO grades “EG-C” or “EG-D”. The
warning light should go off after the 2-
stroke engine oil tank has been refi-
lled.
NOTE:
If the warning light does not come on
when the key is in the “h” position or
does not go off after the 2-stroke
engine oil tank has been refilled, have
a Yamaha dealer check the electrical
circuit.
ECA10010
CAUTION:
Do not operate the vehicle until you
know that the engine oil level is suf-
ficient.
km/h
01020304050607080
1
2345
km/h
01020304050607080
1
234
INSTRUMENT AND CONTROL FUNCTIONS
3-2
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 18
Page 19 of 72
EAU11431
Coolant temperature warning light
“y” (for CS50Z)
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and
allow the engine to cool.
ECA10020
CAUTION:
Do not operate the engine if it is
overheated.
EAU11591
Speedometer
1. Speedometer
1. Speedometer
UK ONLY
1. Speedometer
1. Speedometer
The speedometer shows the riding
speed.
km/hmph
0
10
20
3040
50
01020304050
60
70
80
CS50Z
1
km/hmph
0
10
20
3040
50
01020304050
60
70
80
1
CS50/CS50M
km/h
010
20
30405060
70
80
CS50Z
1
km/h
010
20
30405060
70
80
CS50/CS50M
1
INSTRUMENT AND CONTROL FUNCTIONS
3-3
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 19
Page 20 of 72
EAUS1420
Multi-function display
1. Button
2. Odometer/Tripmeter
3. Digital clock
4. Fuel meter
EWA12311
s s
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function display.
The multi-function display is equip-
ped with the following:
●a digital clock
●an odometer (which shows the
total distance traveled)
●a tripmeter (which shows the dis-
tance traveled since it was last
set to zero)
●a fuel gauge
●a self-diagnosis device
●a function button (which selects
and resets various modes of the
multi-function display)
NOTE:
●Be sure to turn the key to “f”
before using the button.
●For the U.K. only: The odometer
and tripmeter are displayed in
miles.
To set the clock:
1. Select the odometer and push
the button for at least two
seconds.
2. When the hour digits start flas-
hing, push the button to set the
hours.3. To change the tens digit, push
the button for at least seconds.
4. When the tens digit starts flas-
hing, push the button to set the
tens digit.
5. To change the unit digit, push the
button for at least two seconds.
6. When the unit digit starts flas-
hing, push the button to set the
minutes.
km/h
01020304050607080
12
3
4
INSTRUMENT AND CONTROL FUNCTIONS
3-4
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 20
Page 21 of 72
7. Push the button for at least two
seconds to start the clock.
NOTE:
After setting the clock, be sure to
push the button for at least two
seconds before turning the key to
“e”, otherwise the clock will not be
set.
Odometer and tripmeter modes
Pushing the button switches the dis-
play between the odometer mode
“ODO” and the tripmeter “TRIP” in
the following order:
ODO
TRIP ODO
1. Odometer
2. Tripmeter
To reset the tripmeter, select it by
pushing the button, and then push it
again for at least two seconds.
Fuel gauge
The fuel gauge indicates the amount
of fuel in the fuel tank. The display
segments of the fuel gauge disappear
towards “E” (Empty) as the fuel level
decreases. When only one segment is
left near “E”, refuel as soon as possi-
ble.
Self-diagnosis device
This model is equipped with a self-
diagnosis device for the fuel electrical
circuit.If the fuel electrical circuit is defective,
all LCD segments of the fuel gauge
will flash. If this occurs, have a Yama-
ha dealer check the vehicle.
PRESS
BUTTON
PRESS
BUTTON
INSTRUMENT AND CONTROL FUNCTIONS
3-5
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 21
Page 22 of 72
EAU12347
Handlebar switches
1. Dimmer switch “j/k”
2. Turn signal switch “c/d”
3. Horn switch “a”
1. Start “g”
EAU12400
Dimmer switch “j/k”
Set this switch to “j” for the high
beam and to “k” for the low beam.
EAU12460
Turn signal switch “c/d”
To signal a right-hand turn, push this
switch to “d”. To signal a left-hand
turn, push this switch to “c”. When
released, the switch returns to the
center position. To cancel the turn
signal lights, push the switch in after it
has returned to the center position.
EAU12500
Horn switch “a”
Press this switch to sound the horn.
EAUM1131
Start switch “g”
Push this switch while applying the
front or rear brake to crank the engine
with the starter.
ECA10050
CAUTION:
See page 5-1 for starting instruc-
tions prior to starting the engine.
EAU12900
Front brake lever
1. Front brake lever
The front brake lever is located on the
right handlebar grip. To apply the
front brake, pull this lever toward the
handlebar grip.
1
Right
1
2
3 Left
INSTRUMENT AND CONTROL FUNCTIONS
3-6
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 22
Page 23 of 72
EAU12950
Rear brake lever
1. Rear brake lever
The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the hand-
lebar grip.
EAU13201
Fuel and 2-stroke engine oil
tank caps
1. Oil tank cap
2. Fuel tank cap
The fuel tank cap and the 2-stroke
engine oil tank cap are located under
the seat. (See page 3-10.)
Fuel tank cap
To remove the fuel tank cap, turn it
counterclockwise, and then pull it off.
To install the fuel tank cap, turn it
clockwise.
2-stroke engine oil tank cap
To remove the 2-stroke engine oil tank
cap, pull it off.
To install the 2-stroke engine oil tank
cap, push it into the oil tank opening.
EWA10140
s s
WARNING
Make sure that the fuel and 2-stro-
ke engine oil tank caps are properly
installed before riding the scooter.
INSTRUMENT AND CONTROL FUNCTIONS
3-7
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 23
Page 24 of 72
EAU13211
Fuel
1. Fuel tank filler tube
2. Fuel level
Make sure that there is sufficient fuel
in the tank. Fill the fuel tank to the
bottom of the filler tube as shown.
EWA10880
s s
WARNING
●Do not overfill the fuel tank,
otherwise it may overflow
when the fuel warms up and
expands.
●Avoid spilling fuel on the hot
engine.
ECA10070
CAUTION:
Immediately wipe off spilled fuel
with a clean, dry, soft cloth, since
fuel may deteriorate painted surfa-
ces or plastic parts.
EAU13270
Your Yamaha engine has been desig-
ned to use regular unleaded gasoline
with a research octane number of 91
or higher. If knocking (or pinging)
occurs, use a gasoline of a different
brand or premium unleaded fuel. Use
of unleaded fuel will extend spark
plug life and reduce maintenance
costs.
EAU13431
Catalytic converter
This model is equipped with a cataly-
tic converter in the exhaust system.
EWA10860
s s
WARNING
The exhaust system is hot after
operation. Make sure that the
exhaust system has cooled down
before doing any maintenance
work.
ECA10700
CAUTION:
The following precautions must be
observed to prevent a fire hazard or
other damages.
●Use only unleaded gasoline.
The use of leaded gasoline will
cause unrepairable damage to
the catalytic converter.
●Never park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.
●Do not allow the engine to idle
too long.
Recommended fuel:
REGULAR UNLEADED GASOLINE
ONLY
Fuel tank capacity:
5.5 L (1.45 US gal) (1.21 Imp.gal)
Fuel reserve amount:
1.9 L (0.50 US gal) (0.42 Imp.gal)
1
2
ZAUM0020
INSTRUMENT AND CONTROL FUNCTIONS
3-8
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 24
