2008 TOYOTA LAND CRUISER ECO mode

256
3−1. Using the air conditioning system and defogger
Rear window and outside rear view mir ror defoggers
nThe rear window and outside rear vi ew mirror defoggers can be oper
ated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
CAUTION
nWhen the outside rear view mirror defoggers are on
Do not touch the rear view mirror surfaces, as they can become very hot and
burn you.
These features are used to defog the rear window, and to remove
raindrops, dew and frost from the outside rear view mirrors.
With navigation system
On/off
The defoggers will automati−
cally turn off after 15 to 225
minutes. The operation time
changes according to the
ambient temperature and vehi−
cle speed. Pressing the switch
again also turns the defoggers
off.
Without navigation system

257
3−1. Using the air conditioning system and defogger
3
Interior features
W indshield wiper de−icer
nThe windshield wiper deicer can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
CAUTION
nWhen the windshield wiper deicer is on
Do not touch the glass at the lower part of the windshield or to the side of the
front pillars as the surfaces can become very hot and burn you.
This feature is used to prevent ice from building up on the wind
shield and wiper blades.
With navigation system
On/off
The windshield wiper de−icer
will automatically turn off after
approximately 15 minutes.
Pressing the switch again also
turns the de−icer off.
Without navigation system

277
3−2. Using the audio system
3
Interior features
nLens cleaners
Do not use lens cleaners. Doing so may damage the CD player.
nMP3 and WMA files
MP3 (MPEG Audio LAYER3) is a standard audio compression format.
Files can be compressed to approximately 1/10 of their original size by using
MP3 compression.
WMA (Windows Media
TM Audio) is a Microsoft audio compression format.
This format compresses audio data to a size smaller than that of the MP3
format.
There is a limit to the MP3 and WMA file standards and to the media/formats
recorded by them that can be used.
lMP3 file compatibility
Compatible standards
MP3 (MPEG1 LAYER3, MPEG2 LSF LAYER3)
Compatible sampling frequencies
MPEG1 LAYER3: 32, 44.1, 48 (kHz)
MPEG2 LSF LAYER3: 16, 22.05, 24 (kHz)
Compatible bit rates
MPEG1 LAYER3: 64, 80, 96, 112, 128, 160, 192, 224, 256, 320 (kbps)
MPEG2 LSF LAYER3: 64, 80, 96, 112, 128, 144, 160 (kbps)
* Compatible with VBR
Compatible channel modes: stereo, joint stereo, dual channel and
monaural
lWMA file compatibility
Compatible standards
WMA Ver. 7, 8, 9
Compatible sampling frequencies
32, 44.1, 48 (kHz)
Compatible bit rates
Ver. 7, 8: CBR 48, 64, 80, 96, 128, 160, 192 (kbps)
Ver. 9: CBR 48, 64, 80, 96, 128, 160, 192, 256, 320 (kbps)
* Only compatible with 2−channel playback

278 3−2. Using the audio system
lCompatible media
Media that can be used for MP3 and WMA playback are CD−Rs and CD−
RWs.
Playback in some instances may not be possible, depending on the status
of the CD−R or CD−RW. Playback may not be possible or the audio may
jump if the disc is scratched or marked with fingerprints.
lCompatible disc formats
The following disc formats can be used.
Disc formats: CD−ROM Mode 1 and Mode 2
CD−ROM XA Mode 2, Form 1 and Form 2
File formats: ISO9660 Level 1, Level 2, (Romeo, Joliet)
MP3 and WMA files written in any format other than those listed above
may not play correctly, and their file names and folder names may not
be displayed correctly.
Items related to standards and limitations are as follows.
Maximum directory hierarchy: 8 levels
Maximum length of folder names/file names: 32 characters
Maximum number of folders: 192 (including the root)
Maximum number of files per disc: 255
lFile names
The only files that can be recogniz
ed as MP3/WMA and played are those
with the extension .mp3 or .wma.
lMulti−sessions
As the audio system is compatible with multi−sessions, it is possible to play
discs that contain MP3 and WMA files. However, only the first session can
be played.
lID3 and WMA tags
ID3 tags can be added to MP3 files, making it possible to record the track
title and artist name, etc.
The system is compatible with ID3 Ver. 1.0, 1.1, and Ver. 2.2, 2.3 ID3 tags.
(The number of characters is based on ID3 Ver. 1.0 and 1.1.)
WMA tags can be added to WMA files, making it possible to record the
track title and artist name in the same way as with ID3 tags.

287
3−3. Using the rear seat entertainment system
3
Interior features
nTilting the display
The display angles change as
follows each time is
pressed.
The display angle is memorized
and will be recalled when the
“ENGINE START STOP” switch is
turned to ACCESSORY or IGNI−
TION ON mode again.
nCaution screen
This screen appears for a few
seconds when the rear display is
opened. During this time, only
can be operated.
Headphone jacks
To listen to the rear audio, use
headphones.
To use the headphones
Connect them to the jack.
To adjust the volume
Turn the knob clockwise to
increase the volume. Turn the
knob counterclockwise to
decrease the volume.

289
3−3. Using the rear seat entertainment system
3
Interior features
nThe rear seat entertainment system can be used when
The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON
mode.
nJam protection function
The display will stop closing and return to its previous position if something
gets in the way of it closing.
nWhen
appears on the screen
It indicates that the selected icon cannot be used at this time.
n
”Navigation System Owner ’s Manual”
n
Before using the controller (for new vehicle owners)
nWhen the controller batteries are fully depleted
nHeadphones
With some headphones generally available in the market, it may be difficult
to catch signals properly. Toyota recommends the use of Toyota genuine
wireless headphones.
Contact your Toyota dealer for further details.
An insulating sheet is set to prevent the
batteries from being depleted. Remove
the insulating sheet before using the
remote control.
Remove the depleted batteries and install
new batteries.

373
4−3. Do−it−yourself maintenance
4
Maintenance and care
CAUTION
The engine compartment contains many mechanisms and fluids that may
move suddenly, become hot, or become electrically energized. To avoid death
or serious injury.
nWhen working on the engine compartment
lKeep hands, clothing, and tools away from the moving fan and engine
drive belt.
lBe careful not to touch the engine, inverter, radiator, exhaust manifold, etc.
right after driving as they may be hot. Oil and other fluids may also be hot.
lDo not leave anything that may burn easily, such as paper or rags, in the
engine compartment.
lDo not smoke, cause sparks or expose an open flame to fuel or the bat−
tery. Fuel and battery fumes are flammable.
lBe extremely cautious when working on the battery. It contains poisonous
and corrosive sulfuric acid.
nWhen working near the electric cooling fan or radiator grille
Be sure the ignition is off. With the “ENGINE START STOP” switch in IGNI−
TION ON mode, the electric cooling fan may automatically start to run if the
air conditioning is on and/or if the coolant temperature is high.
(P. 383)
nWhen working on or under the vehicle
lDo not get under the vehicle with just the jack supporting it.
Always use automotive jack stands or other solid supports.
lUse eye protection to prevent flying or falling material, fluid spray, etc. from
getting in your eyes.
NOTICE
nIf you remove the air cleaner filter
Driving with the air cleaner filter removed may cause excessive engine wear
due to dirt in the air. Also a backfire could cause a fire in the engine compart−
ment.

380 4−3. Do−it−yourself maintenance
nEngine oil consumption
lThe amount of engine oil consumed depends on the oil viscosity, the
quality of the oil and the way the vehicle is driven.
lMore oil is consumed under driving conditions such as high speeds and
frequent acceleration and deceleration.
lA new engine consumes more oil.
lWhen judging the amount of oil consumption, keep in mind that the oil
may have become diluted, making it difficult to judge the true level accu−
rately.
nResetting the engine oil maintenance data
The oil change system should be reset. Perform the following procedures:
Switch the display to the trip meter A when the engine is running.
( P. 161)
Turn the “ENGINE START STOP” switch OFF.
While pressing the trip meter reset button, set the “ENGINE START
STOP” switch to IGNITION ON mode (but do not start the engine
because otherwise the reset mode will be cancelled). Continue to
press and hold the button until the multi−information display indi−
cates that the reset is complete.
STEP1
STEP 2
STEP 3