2008 TOYOTA LAND CRUISER Shift lock

191
2−4. Using other driving systems
2
When driving
Shifting between “H4”and “L4”
nShifting from “H4” to “L4”
Stop the vehicle completely.
Shift the shift lever to “N”.
Push and turn the four−wheel drive control switch fully clock−
wise.
Maintain this condition until the low speed four−wheel drive indica−
tor light turns on.
nShifting from “L4” to “H4”
Stop the vehicle completely.
Shift the shift lever to “N”.
Turn the four−wheel drive control switch fully counterclock−
wise.
Maintain this condition until the low speed four−wheel drive indica−
tor light turns off.
STEP1
STEP 2
STEP 3
STEP 1
STEP 2
STEP 3

192 2−4. Using other driving systems
Neutral position
Shifting to the neutral position cuts drive power to the wheels.
n
Shifting from “H4” to the neutral position
Stop the vehicle completely.
Make sure the vehicle is stopped in a safe place while carrying out
the following procedure.
Confirm the following:
lThe four wheel−drive control switch is in “H4”. (The low speed four−
wheel drive indicator light is not illuminated.)
If the switch is in “L4”, turn it to “H4”. (
P. 190)
lThe center differential is unlocked. (The center differential lock indi−
cator light is not illuminated.)
If the center differential is locked,
press the center differential lock/
unlock switch to unlock the center differential. ( P. 190)
Set the parking brake firmly and put the shift lever in “N”.
Turn the engine off if the engine is running, then turn the
“ENGINE START STOP” switch to the IGNITION ON mode.
Do not start the engine till the end of the procedure.
Shift the shift lever to “P”.
Depress and release the brake pedal 3 times.
Depress the pedal firmly each time, then keep the pedal depressed
the third time.
Shift the shift lever to “N”.
Depress and release the brake pedal 3 times.
Release the brake pedal once and then depress and release the
brake pedal 3 times.
Depress the pedal firmly each time, then keep the pedal depressed
the third time.
STEP1
STEP 2
STEP 3
STEP 4
STEP 5
STEP6
STEP 7
STEP 8

194 2−4. Using other driving systems
nThe fourwheel drive control switch can be operated when
lThe “ENGINE START STOP” switch is in IGNITION ON mode.
lThe shift lever is in the “N” position.
lThe vehicle is stopped completely.
nAdvice for driving on slippery roads in “L4” (low speed position)
lIf you shift the four−wheel drive control switch to “L4” and the shift lever to
the “2” range of “S” while driving in steep off−road areas, the output of the
brake can be controlled effectively by the active traction control system,
which assists the driver to control the driving power of 4 wheels.
lUse the “1” range of “S” of the shift lever for maximum power and traction
when your wheels get stuck or when driving down a steep incline. In the
following cases, the output of the brake can be controlled by the active
traction control system if the engine speed is under 3,000 rpm (normally
under 3,000 rpm when the wheels get unstuck).
The four−wheel drive control switch is in the “L4” position and the shift
lever is in the “1” range of “S” or the shift lever is in “D” or “S” with the
transmission downshifted to first gear.
The four−wheel drive control switch is in the “L4” position and the shift
lever is in the “R” position.
nThe center differential lock/unlock button can be operated when
lThe “ENGINE START STOP” switch is in IGNITION ON mode.
lThe vehicle speed is less than 60 mph (100 km/h).
nLocking/unlocking the center differential
lWhen the center differential is locked, VSC (vehicle stability control) is
automatically turned off. (The center di
fferential lock and “VSC OFF” indi−
cator lights come on.)
lIf the operation is not completed, the center differential lock indicator
blinks. If the indicator light does not turn off when unlocking the center
differential, drive straight ahead while accelerating or decelerating, or
drive in reverse.
lIf the center differential lock/unlock is not completed within 5 seconds
while the cruise control system is on, cancel the cruise control system.

195
2−4. Using other driving systems
2
When driving
nIf the low speed fourwheel drive in dicator light or the center differen
tial lock indicator light blinks
lIf the low speed four−wheel drive indicator light continues to blink when
using the four−wheel drive control switch, stop the vehicle completely,
move the shift lever to “N” and operate the switch again.
lIf the shift lever is moved before the low speed four−wheel drive indicator
light has turned on/off, a beep sounds and the transfer position may not
successfully change. In this case, stop the vehicle completely, return the
shift lever to “N” and operate the switch again.
lIf the engine coolant temperature is too low, the four−wheel drive control
system may not be able to shift. When the engine is warmer press the
switch again.
If the low speed four−wheel drive indicator light or the center differential lock
indicator light continues to blink even after attempting the above, there may
be a malfunction in the engine, the brake system or the four−wheel drive sys−
tem. In this case, you may not be able to shift between “H4” and “L4”, and
the center differential lock may not be operable. Have the vehicle inspected
by your Toyota dealer immediately.

213
2−5. Driving information
2
When driving
NOTICE
nTo prevent the water damage
Take all necessary safety measures to ensure that water damage to the
engine or other components does not occur.
lWater entering the engine air intake will cause severe engine damage.
lWater entering the automatic transmission will cause deterioration in shift
quality, locking up of your transmission accompanied by vibration, and ulti−
mately damage.
lWater can wash the grease from wheel bearings, causing rusting and pre−
mature failure, and may also enter the differentials, transmission and
transfer case, reducing the gear oil’s lubricating qualities.
nWhen you drive through water
If driving through water, such as when crossing shallow streams, first check
the depth of the water and the bottom of the river bed for firmness. Drive
slowly and avoid deep water.
nInspection after offroad driving
l
Sand and mud that has accumulat ed in brake drums and around brake
discs may affect braking efficiency and may damage brake system compo−
nents.
l
Always perform a maintenance inspection after each day of off−road driv−
ing that has taken you through rough terrain, sand, mud, or water. For
scheduled maintenance information, refer to the “Scheduled Maintenance
Guide” or “Owner ’s Manual Supplement”.

218 2−5. Driving information
CAUTION
n Things that must not be carried in the luggage compartment
The following things may cause a fire if loaded in the luggage compart−
ment.
lReceptacles containing gasoline
lAerosol cans
n Storage precautions
lDo not stack anything in the luggage compartment higher than the
seatbacks.
Such items may be thrown about and possibly injure people in the
vehicle during sudden braking or in an accident.
lDo not place cargo or luggage in or on the following locations as the
item may get under the brake or accelerator pedal and prevent the
pedals from being depressed properly
, block the driver ’s vision, or hit
the driver or passengers, causing an accident.
Feet of the driver
Front passenger or rear seats (when stacking items)
Instrument panel
Dashboard
Auxiliary box or tray that has no lid
lSecure all items in the occupant compartment, as they may shift and
injure someone during an accident or sudden braking.
lNever allow anyone to ride in the luggage compartment. It is not
designed for passengers. They should ride in their seats with their seat
belts properly fastened. Otherwise, th
ey are much more likely to suffer
death or serious injury, in the event of sudden braking or a collision.

235
2−5. Driving information
2
When driving
lAlways place wheel blocks under both the vehicle and the trailer
wheels when parking. Apply the parking brake firmly, and put the
transmission in “P”. Avoid parking on a slope, but if unavoidable,
do so only after performing the following:
Apply the brakes and keep them applied.
Have someone place wheel bloc
ks under both the vehicle and
trailer wheels.
When the wheel blocks are in pl
ace, release the brakes slowly
until the blocks absorb the load.
Apply the parking brake firmly.
Shift into “P” and turn off the engine.
lWhen restarting after parking on a slope:
With the transmission in the “P ” position, start the engine. Be
sure to keep the brake pedal pressed.
Shift into “3”, “2”, “1”, or “R” position (if reversing).
Release the parking brake and
brake pedal, and slowly pull or
back away from the wheel blocks. Stop and apply the brakes.
Have someone retrieve the blocks.
STEP1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 1
STEP 2
STEP 3
STEP 4

368 4−2. Maintenance
Vehicle interior
Items Check points
Accelerator pedalMoves smoothly (without uneven
pedal effort or catching)?
Automatic transmission “Park”
mechanismCan the vehicle be hold securely
on an incline with the shift lever in
“P”?
Brake pedalMoves smoothly?
Does it have appropriate clear−
ance and correct amount of free
play?
BrakesPulls to one side when applied?
Loss of brake effectiveness?
Spongy feeling brake pedal?
Pedal almost touches floor?
Head restraintsMove smoothly and lock
securely?
Indicators/buzzersFunction properly?
LightsDo all the lights come on?
Headlights aimed correctly?
Parking brakeMoves smoothly?
Can hold the vehicle securely on
an incline?
Seat beltsDoes the seat belt system oper−
ate smoothly?
Are the belts undamaged?
SeatsDo the seat controls operate
properly?
Steering wheel
Moves smoothly?
Has correct free play?
No strange noises?