2008 TOYOTA LAND CRUISER start stop button

31
1−2. Opening, closing and locking the doors
1
Before driving
nSwitching the door unlock function
If it is possible to set which doors the entry function unlocks.
Turn the “ENGINE START STOP” switch OFF.
When the indicator on the key surface is turned off, press and hold
, or for approximately 5 seconds while pressing
on the key.
The setting changes each time an operation is preformed, as shown below.
(When changing the setting continuously, release the buttons, wait for at least
5 seconds, and repeat step 2.)
STEP1
STEP 2
Multi−information
displayUnlocking function Beep
Hold the driver ’s door han−
dle to unlock only the
driver ’s door.Exterior: Beeps three
times
Interior: Pings once
Hold either door handle to
unlock all doors.
Exterior: Beeps twice
Interior: Pings once

44 1−2. Opening, closing and locking the doors
Locking the driver ’s doors from the outside without a key
Move the inside lock button to the lock position.
Close the door.
The door cannot be locked if the “ENGINE START STOP” switch is in
ACCESSORY or IGNITION ON mode, or the electronic key is left
inside the vehicle.
The key may not be detected correctly and the door may be locked.
Rear door childprotector lock
The door cannot be opened from
inside the vehicle when the locks
are set.
These locks can be set to prevent
children from opening the rear
doors. Press down rear door
switches to lock the rear doors.
STEP1
STEP 2
ITY12C032

63
1−3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before performing
the following:
Using the wireless remote control
Turn the “ENGINE START STOP” switch to OFF and close
the driver ’s door.
While pressing the desired but−
ton (“1”, “2” or “3”), press
on the wireless remote control
until the signal beeps.
The driving position is recalled
when the driver ’s door is
unlocked using the entry function
or wireless remote control and the
driver ’s door is opened.
STEP1
1SET23
ITY13C130
STEP2
nCanceling the linked door unlock operation
Turn the “ENGINE START STOP” switch to OFF and close the
driver ’s door.
Using the wireless remote control: While pressing “SET” button,
press button on the wireless remote control until the signal
beeps.
STEP1
STEP 2

64 1−3. Adjustable components (seats, mirrors, steering wheel)
nRetained accessory power
Each memorized position (except for the steering wheel position) can be
activated within 30 seconds after the driver ’s door is opened, even if the
“ENGINE START STOP” switch turns off.
nTo cancel seat position recall
Perform any one of the following operations.
lPress the “SET” button
lPress button “1”, “2” or “3”.
lAdjust the seat using the switches (only cancels seat position recall)
nIf the battery is disconnected
The memorized positions must be reset because the computer ’s memory is
erased when the battery is disconnected.
CAUTION
nSeat adjustment caution
Take care during seat adjustment that the seat does not strike the rear pas−
senger or squeeze your body against the steering wheel.

98 1−6. Theft deterrent system
nItems to check before locking the vehicle
To prevent unexpected triggering of the alarm and vehicle theft, make sure
of the following.
lNobody is in the vehicle.
lThe windows and moon roof are closed before the alarm is set.
lNo valuables or other personal items are left in the vehicle.
nTriggering of the alarm
The alarm may be triggered in the following situations.
(Stopping the alarm deactivates the alarm system.)
lA person inside the vehicle opens a door or hood.
lThe battery is recharged or replaced when the vehicle is locked.
n
Panic mode
nDeactivating or stopping the alarm
Do one of the following to deactivate or stop the alarm.
lUnlock the doors using the smar t key system or the wireless
remote control.
lStart the engine. (The alarm will be deactivated or stopped after
a few seconds.)
When is pressed for longer than
about one second, the headlights/tail
lights/emergency flashers will flash, the
front and rear interior lights will come on,
and an alarm will sound for about 60 sec−
onds to deter any person from trying to
break into or damage your vehicle.
To stop the alarm, press any button on
the wireless remote control.

194 2−4. Using other driving systems
nThe fourwheel drive control switch can be operated when
lThe “ENGINE START STOP” switch is in IGNITION ON mode.
lThe shift lever is in the “N” position.
lThe vehicle is stopped completely.
nAdvice for driving on slippery roads in “L4” (low speed position)
lIf you shift the four−wheel drive control switch to “L4” and the shift lever to
the “2” range of “S” while driving in steep off−road areas, the output of the
brake can be controlled effectively by the active traction control system,
which assists the driver to control the driving power of 4 wheels.
lUse the “1” range of “S” of the shift lever for maximum power and traction
when your wheels get stuck or when driving down a steep incline. In the
following cases, the output of the brake can be controlled by the active
traction control system if the engine speed is under 3,000 rpm (normally
under 3,000 rpm when the wheels get unstuck).
The four−wheel drive control switch is in the “L4” position and the shift
lever is in the “1” range of “S” or the shift lever is in “D” or “S” with the
transmission downshifted to first gear.
The four−wheel drive control switch is in the “L4” position and the shift
lever is in the “R” position.
nThe center differential lock/unlock button can be operated when
lThe “ENGINE START STOP” switch is in IGNITION ON mode.
lThe vehicle speed is less than 60 mph (100 km/h).
nLocking/unlocking the center differential
lWhen the center differential is locked, VSC (vehicle stability control) is
automatically turned off. (The center di
fferential lock and “VSC OFF” indi−
cator lights come on.)
lIf the operation is not completed, the center differential lock indicator
blinks. If the indicator light does not turn off when unlocking the center
differential, drive straight ahead while accelerating or decelerating, or
drive in reverse.
lIf the center differential lock/unlock is not completed within 5 seconds
while the cruise control system is on, cancel the cruise control system.

380 4−3. Do−it−yourself maintenance
nEngine oil consumption
lThe amount of engine oil consumed depends on the oil viscosity, the
quality of the oil and the way the vehicle is driven.
lMore oil is consumed under driving conditions such as high speeds and
frequent acceleration and deceleration.
lA new engine consumes more oil.
lWhen judging the amount of oil consumption, keep in mind that the oil
may have become diluted, making it difficult to judge the true level accu−
rately.
nResetting the engine oil maintenance data
The oil change system should be reset. Perform the following procedures:
Switch the display to the trip meter A when the engine is running.
( P. 161)
Turn the “ENGINE START STOP” switch OFF.
While pressing the trip meter reset button, set the “ENGINE START
STOP” switch to IGNITION ON mode (but do not start the engine
because otherwise the reset mode will be cancelled). Continue to
press and hold the button until the multi−information display indi−
cates that the reset is complete.
STEP1
STEP 2
STEP 3

478
5−2. Steps to take in an emergency
If the shift lever cannot be shifted from P
If the shift lever cannot be shifted with your foot on the brake, there
may be a problem with the shif
t lock system (a system to prevent
accidental operation of the shift lever). Have the vehicle inspected by
your Toyota dealer immediately.
The following steps may be used as an emergency measure to
ensure that the shift
lever can be shifted.
Set the parking brake.
Set the “ENGINE START STOP” switch to the ACCES−
SORY mode.
Depress the brake pedal.
Pry the cover up with a flat−
head screwdriver or equiva−
lent.
Press the shift lock override
button.
The shift lever can be shifted
while the button is pressed.
STEP1
STEP 2
STEP 3
STEP 4
P
R
N
+
SD
ITY51C041
P
R
N
+
SD
ITY51C042
STEP5