2008 SUZUKI GRAND VITARA heating

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
A. WARNING
(Continued) • Always return the ignition switch to the "LOCK" position and remove
the ignition key and the remote controller (if equipped) when leav­ing the vehicle even if a short time. Also do not leave children or pets alone in a parked vehicle. Unat­
tended children could cause acci­dental movement of the vehicle or could tamper with power windows or power sunroof. They also could suffer from heat stroke in warm or hot weather. These could result in
severe injury or even death.
CAUTION
• Do not use the starter motor for more than 15 seconds at a time.
For diesel engine model, do not use the starter motor for more than 30 seconds at a time. If the engine
does not start, wait 15 seconds
before trying again. If the engine
does not start after several attempts, check the fuel and igni­tion systems or consult your SUZUKI dealer.
• Do not leave the ignition switch in
the "ON" position if the engine is not running as the battery will dis­charge.
3-7
Parking Brake Lever
EXAMPLE
(1) To set (2) To release (3) To release
64J081
The parking brake lever is located between the seats. To set the parking brake, hold the brake pedal down and pull the parking
brake lever all the way up. To release the parking brake, hold the brake pedal down, pull up slightly on the parking brake lever, push the button on the end of the lever with
your thumb, and lower the lever to its origi­nal position. For
automatic transmission
vehicles,
always set the parking brake before mov­ing the gearshift lever to the "P" (PARK) position. If you park on an incline and shift
into "P" before setting the parking brake, the weight of the vehicle may make it diffi­cult to shift out of "P" when you are ready to drive the vehicle.
When preparing to drive the vehicle, move the gearshift lever out of the "P" position
before releasing the parking brake.
A. WARNING
• Never drive your vehicle with the
parking brake on: rear brake effec­
tiveness can be reduced from over­
heating, brake life may be
shortened,
or permanent brake
damage may result.
• If
the parking brake does not hold the vehicle securely or does not fully release, have your vehicle inspected immediately by an autho­
rized SUZUKI dealer.

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
A. WARNING
Do not "ride" the brakes by applying
them continuously or resting your
foot
on the pedal. This will result in overheating of the brakes which
could cause unpredictable braking
action, longer stopping distances, or
permanent brake damage.
Accelerator Pedal (3) This pedal controls the speed of the
engine. Depressing the accelerator pedal
increases power output
and speed.
3-9
Starting the Engine
Before Starting the Engine
64J140
1} Make sure the parking brake is set fully. 2} Manual transmission -Shift into UN" (Neutral) and depress the clutch pedal
all the way to the floor. Hold the clutch
pedal while starting the engine.
Automatic transmission -
If the gear­
shift lever is not in Up" (Park) position,
shift into Up" (Park). (If you need to re­start the engine while the vehicle is moving, shift into UN".)
NOTE: Automatic transmission vehicles have a starter interlock device which is designed to keep the starter from operating if the transmission is in any of the drive posi­
tions.
A. WARNING
Make sure that the parking brake is set fully and the transmission is in Neutral (or Park for vehicles with an automatic transmission) before
attempting to start the engine.

Downloaded from www.Manualslib.com manuals search engine ES~ systems (other than ABS) will be
canceled to provide improved vehicle
traction, and the
~'ESP OFF" indicator
light will come on. When the transfer switch (if equipped) is
turned to the "4L LOCK" position, brake­
traction control can be activated. Brake­
traction control brakes the spinning
wheel to distribute drive power to the other wheels for increased climbing abil­
ity or for better performance on a rolling
hill or a slipe,ery surface .. • If the ESpE> systems operate continu­ously, such as when driving on slippery roads, the traction control functions of the ES~ systems may be canceled
temporarily to avoid overheating the brake pads, and the "ESP OFF" indicator
light will come on. After a short period of time, the ES~ systems (other than ABS) will turn on automatically and the "ESP OFF" indicator light will go out. • If your vehicle is equipped with a hill
descent control system and a hill hold
control system, these systems will not be
turned off
when the "ESP OFF" switch is pushed to turn off the ES~ systems.
E'::.F' OFF I-Qf - -a.'ND S\l',/IT'_ H V"/I)R~;',. I-6-t ONL ',' IN 4HL
79K084
NOTE: If, you push the "ESP OFF" switch when the transfer switch is in the "4H" position, the ES~ systems will not be turned off, and the message shown in the above illus­
tration will appear on the information dis­play. You should turn the transfer switch to the "4H LOCK" position to turn off the ES~ systems. Refer to "Using the Transfer Switch" in this section.
ABS Warning Light I Brake System
Warning Light
See 'Braking" in the "OPERATING YOUR VEHICLE" section.
OPERATING YOUR VEHICLE
Hill descent control System
(if equipped)
The hill descent control system is designed
to reduce the driver's workload when going
down steep, rough and/or slippery hills where the vehicle cannot decelerate enough by engine braking alone. The hill descent control system helps to control
vehicle speed by automatically engaging
the vehicle's brakes, as needed, so you can concentrate on steering the vehicle.
A WARNING
Do not rely excessively on the hill
descent control system. The hill
descent control system may not con­trol vehicle speed on a hill under all load or road conditions. Always be prepared to control vehicle speed by applying the brakes. Failure to pay
attention and control vehicle speed
using the brakes when necessary
may
result in loss' of control or an accident.
3-36