2008 SUZUKI GRAND VITARA light

Downloaded from www.Manualslib.com manuals search engine Center Interior Light (if equipped)
64J159
Pull down the lens by using a plane screw
driver covered with a soft cloth as shown. To install it, simply push it back in.
The bulb can be removed by simply pulling it out. When replacing the bulb, make sure
that the contact springs are holding the bulb securely.
Rear Interior Light (if equipped)
64J160
Pull down the lens by using a plane screw
driver covered with a soft cloth as shown. To install it, simply push it back in. .
The
bulb can be removed by simply pulling it out.
INSPECTION AND MAINTENANCE
Spot Light (if equipped) . Pull down the lens by using a plane screw
driver covered with a soft cloth as shown.
Ceiling-mount type (if equipped)
79K061
Remove the bulb holder by turning it coun­terclockwise. Pull out the bulb.
7-36

Downloaded from www.Manualslib.com manuals search engine INSPECTION AND M AINTENANCE
Headlight
For 3 door model
7-37
Open the . coupler R engine hood O' 65D150 P . emove the seaiin Isconnect the
ush the r .. grubber.
unhook it T
etalnlng sprin
new bulb'. hen remove th 9 ~orward and In the reverse ord e ulb. Install a
er of removal.
For5doo=r~m=-o~de-I-------------­
Low beam • Halogen head lamp
79K089

Downloaded from www.Manualslib.com manuals search engine Open the engine hood. Disconnect the Front Fog Light coupler. Remove the sealing rubber.
Push the retaining spring forward and
unhook it. Then remove the bulb. Install a
new bulb in the reverse order of removal.
•
Discharge head lamp
Since special procedures are required, we recommend you take your vehicle to your SUZUKI dealer for bulb replacement.
High beam
78F072
Open the engine hood. Disconnect the coupler while pushing the lock release. Turn the bulb holder counterclockwise to remove it.
II~
~1
79K090
1) Insert a flat blade screw driver into the hole (2) and remove the clips (1) by twist the driver as shown in the illustra-tion. .
2) Remove the bolt (3) by a Phillips-head screw driver. .
INSPECTION AND MAINTENANCE
79K091
3) Remove the clip (4) with the same way as No.1).
7-38

Downloaded from www.Manualslib.com manuals search engine INSPECTION AND MAINTENANCE
78F072
4) Open the fender cover. Disconnect the
coupler with pushing the lock release.
Turn the bulb holder counterclockwise
and remove it.
7-39
Other General Lights
Bulb holder
EXAMPLE 0 "'"
o (2~
~
(2) ,~
(1) ~.
(1) Removal (2) Installation
54G123
To remove a bulb holder from a light hous­
ing, turn the holder counterclockwise and
pull
it out. To install the holder, push the
holder in and turn it clockwise.
Bulb
EXAMPLE~
.. O~y
X?3
-< ~~
~& "~d
(1) • B>~
.(3) r<0' Q(4) V-=-(2)
(3) Removal
(4) Installation
54G124
There are two types of bulb, "Full glass type" (1) and "Glass/metal type" (2).
To remove and install a full glass type bulb
(1), simply pull out or push in the bulb.
To remove a glass metal type bulb (2) from
a bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
You can access the individual bulb or bulb
holders as follows.

Downloaded from www.Manualslib.com manuals search engine Parking light Front turn signal light
For 3 door model
64J193
For 5 door model
To replace the bulb of parking/turn signal
light, follow the procedure for the bulb
replacement of the "Front Fog Light".
Rear combination light
78K124
Side turn signal light
64J195
INSPECTION AND MAINTENANCE
As the bulb is built-in type, the light assem­bly must be replaced. Remove the light
assembly by sliding the light housing left­ward with your finger.
License plate light
65J345
Turn the cover (1) counterclockwise to
remove it.
NOTE: When reinstalling, put the packing . (2)
between the cover and bulb holder.
7-40

Downloaded from www.Manualslib.com manuals search engine INSPECTION AND MAINTENANCE
Door illumination light (for 5 door model)
Luggage compartment light
7-41
64J166
High-mount stop light (if equipped) The followings are the general procedure
for replace the bulbs of high-mount stop
light.
Since special procedures are required, we recommend you take your vehicle to your SUZUKI dealer for the bulbs of high-mount
stop light replacement.
To remove a high-mounted stop light hous­
ing the following procedure:
1) Open the tailgate, and remove the trim
(1) as shown in the illustration.
64J182
2) Release the claws of the light housing
by the flat head etc. through the service
holes as shown
in the illustration.

Downloaded from www.Manualslib.com manuals search engine (2)
64J183
3) Close the tailgate. Remove a high­
mounted stop light housing (2) from the tailgate.
64J184
4) Remove the each bulb. 5) Replace the bulbs. To install a high-mounted stop light housing in the reverse order of removal.
INSPECTION AND MAINTENANCE
Wiper Blades
54G129
If the wiper blades become brittle or dam­
aged, or make streaks when wiping,
replace the wiper blades.
To install new wiper blades, follow the pro­
cedures below.
CAUTION
To avoid scratching or breaking the
window, do not let the wiper arm
strike the window while replacing the
wiper blade.
NOTE: Some wiper blades may be different from
the ones described here depending on
vehicle specifications.
If so, consult your SUZUKI dealer for proper replacement
method.
7-42