2008 SATURN VUE Owners Manual

8(Mist):Pull the lever down and release it for a
single wiping cycle. The lever will return to its original
position. For more cycles, hold the lever down
before releasing it.
9(Off):Move the lever to this position to turn off
the wipers.
&(Intermittent):Move the lever to this position to
set a delay between wipes. To set for a shorter or longer
delay between wipes, move the switch on top of the
lever left or right to decrease or increase wiper
movement.
a(Low):Move the lever to this position for slow,
steady wiping cycles.
1(High):Move the lever to this position for rapid
wiping cycles.
Rainsense™ II Wipers
If your vehicle has Rainsense™ II windshield wipers, the
moisture sensor is located next to the inside rearview
mirror and is mounted on the windshield. When active,
these sensors are able to detect moisture on the
windshield and automatically turn on the wipers.To turn on the Rainsense™ feature, the wipers must be
set to one of the ve delay settings on the multifunction
lever. Each of the ve settings adjusts the sensitivity
of the rainsensor.
Since different drivers have different setting preferences,
it is recommended that the mid-range setting (position 3)
be used initially. For more wipes, select the higher
settings; for fewer wipes, select the lower settings located
closer to the off position on the multifunction lever.
The rainsensor will automatically control the frequency
of the wipes from the off setting to the high speed
setting according to the weather conditions. The wipers
can be left in a rainsense mode even when it is not
raining.
When Rainsense™ is active, the headlamps will turn
on automatically if the exterior lamp control is in
the AUTO position and the wipers are active.
Notice:Going through an automatic car wash with
the wipers on can damage them. Turn the wipers
off when going through an automatic car wash.
3-9
ProCarManuals.com

Windshield Washer
{CAUTION:
In freezing weather, do not use your washer
until the windshield is warmed. Otherwise the
washer uid can form ice on the windshield,
blocking your vision.
Pull the windshield wiper lever toward you to spray
washer uid on the windshield. The wipers will run for
a few cycles to clear the windshield. For more wash
cycles, pull the lever forward and hold.
Heated Windshield Washer
If your vehicle has the Rainsense™ windshield wiper
system, the windshield washer uid is heated. For more
information about Rainsense™ wipers, seeRainsense™
II Wipers on page 3-9. The heated windshield washer
only works with the front wiper system, not the rear
wiper system. This feature helps to clear ice, snow,
tree sap, or bugs from the windshield.
The heated windshield washer uid system
automatically turns on when the windshield washer
uid is used while the rear window defogger is turned on.
For more information about the rear window defogger,
seeClimate Control System on page 3-19orAutomatic
Climate Control System on page 3-23. This activation
begins four heated wash/wipe cycles. The rst heated
wash/wipe cycle can take up to 40 seconds to occur,
depending on outside temperature. After the rst wash/
wipe cycle, it can take up to 20 seconds for each of the
remaining cycles.
When the heated windshield washer uid system is
activated under certain outside temperature conditions,
steam might ow out of the washer nozzles for a
short period of time before washer uid is sprayed.
This is a normal condition.
3-10
ProCarManuals.com

Rear Window Wiper/Washer
The rear wiper and rear wash button is located on the
instrument panel above the climate control system.
=(Rear Wiper/Washer):Press this button to wash
and wipe the rear window.
The rear window washer uses the same reservoir as
the windshield washer. Check the windshield washer
reservoir level if the front windshield can be worked, but
no uid is sprayed when the rear washer is activated.
SeeWindshield Washer Fluid on page 5-32.
5(Delay):Press this button to turn the delayed wiping
on or off.
Cruise Control
With cruise control, the vehicle can maintain a speed
of about 25 mph (40 km/h) or more without keeping your
foot on the accelerator. This can really help on long
trips. Cruise control does not work at speeds below
25 mph (40 km/h).
{CAUTION:
Cruise control can be dangerous where you
cannot drive safely at a steady speed. So, do
not use your cruise control on winding roads
or in heavy traffic.
Cruise control can be dangerous on slippery
roads. On such roads, fast changes in tire
traction can cause excessive wheel slip, and
you could lose control. Do not use cruise
control on slippery roads.
3-11
ProCarManuals.com

Setting Cruise Control
{CAUTION:
If you leave your cruise control on when you
are not using cruise, you might hit a button
and go into cruise when you do not want to.
You could be startled and even lose control.
Keep the cruise control switch off until you
want to use cruise control.
The cruise control buttons
are located on the left side
of the steering wheel.
E(On/Off):Press this button to turn the cruise control
system on and off. An indicator light comes on.
RES+ (Resume/Accel):Press the thumbwheel up to
resume a set speed or to accelerate to a higher speed.
−SET (Set/Coast):Press the thumbwheel down to
set a speed or to decrease the speed.
To set a speed do the following:
1. Press the on/off symbol to turn cruise control on.
The indicator light on the button comes on.
2. Get to the speed desired.
3. Press the thumbwheel toward−SET and release it.
4. Take your foot off the accelerator pedal.
When the brakes are applied, the cruise control
shuts off.
Resuming a Set Speed
If the cruise control is set at a desired speed and then
the brakes are applied, the cruise control is disengaged.
The indicator light on the instrument panel cluster goes
out when the cruise is no longer engaged. To return to
the previously set speed, press the thumbwheel up
toward RES+ briey when the vehicle has reached a
speed of about 25 mph (40 km/h) or more.
This accelerates your vehicle to the previously selected
speed.
3-12
ProCarManuals.com

Increasing Speed While Using Cruise
Control
There are two ways to go to a higher speed.
Disengage the cruise control, but do not turn it off.
If the cruise control system is already engaged,
press the thumbwheel up toward RES+ and hold it
until your vehicle accelerates to the desired speed,
and then release the switch. To increase the speed
in very small amounts, press the thumbwheel up
toward RES+ briey and then release it. Each
time this is done, the vehicle will go about 1 mph
(1.6 km/h) faster.
Reducing Speed While Using Cruise
Control
If the cruise control system is already engaged,
Push the thumbwheel toward−SET and hold until
the desired lower speed is reached, then release it.
To slow down in very small amounts, push the
thumbwheel toward−SET briey. Each time this is
done, the vehicle goes about 1 mph (1.6 km/h)
slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase the vehicle’s
speed. When you take your foot off the pedal, the
vehicle will slow down to the previously set cruise
control speed.
Using Cruise Control on Hills
How well the cruise control works on hills depends upon
the vehicle’s speed, load, and the steepness of the
hills. When going up steep hills, you might have to
step on the accelerator pedal to maintain the vehicle’s
speed. When going downhill, you might have to brake
or shift to a lower gear to maintain the vehicle’s
speed. Of course, applying the brakes ends cruise
control. Many drivers nd this to be too much trouble
and do not use cruise control on steep hills.
Ending Cruise Control
There are three ways to disengage the cruise control:
Step lightly on the brake pedal or clutch; when
cruise control disengages, the indicator light on
the instrument panel cluster goes out.
Press the on/off button, this will turn off the cruise
control system.
3-13
ProCarManuals.com

Erasing Speed Memory
The cruise control set speed memory is erased when
the cruise control or the ignition is turned off.
Exterior Lamps
The exterior lamp control is
located on the instrument
panel to the left of the
steering wheel.
The exterior lamp control can be turned to the following
positions:
9(Off):This position turns off the exterior lamps.
The knob returns to the AUTO position after it is
released.
AUTO (Automatic):This position is the automatic
mode for headlamps. The exterior lamps turn on and
off, depending on outside lighting.
;(Parking Lamps):This position turns on the
parking lamps together with the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
2(Headlamps):This position turns on the
headlamps, together with the previously listed lamps
and lights.
Lamps On Reminder
A warning chime sounds, if the driver’s door is opened
while the ignition is off and the lamps are on.
Wiper Activated Headlamps
This feature automatically turns on the headlamps and
parking lamps if the exterior lamp control is set in the
AUTO position and the windshield wipers are turned on
and have completed eight wipe cycles. SeeExterior
Lamps on page 3-14for additional information.
When the ignition is turned off, the wiper-activated
headlamps immediately turn off. They also turn off if
the windshield wiper control is turned off.
3-14
ProCarManuals.com

Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during the day.
DRL can be helpful in many different driving conditions,
but they can be especially helpful in the short periods
after dawn and before sunset. Fully functional daytime
running lamps are required on all vehicles rst sold
in Canada.
The DRL system makes the low-beam headlamps come
on in daylight when the following conditions are met:
The engine is running,
The exterior lamp band is in AUTO, and
The light sensor determines it is daytime.
When the DRL are on, the low-beam headlamps will be
on. The taillamps, sidemarker, and other lamps will
not be on. The instrument panel will not be lit up either.
When the exterior lamp band is turned to the headlamp
position, the regular headlamps will come on. The other
lamps that come on with the headlamps will also
come on.
When the headlamps are turned off, the regular lamps
also turn off, and the low-beam headlamps turn on.
The regular headlamp system should be used when
needed.
Automatic Headlamp System
When it is dark enough outside, the headlamps come
on automatically.
There is a light sensor located on top of the instrument
panel. Make sure it is not covered, or the headlamps
will come on when they are not needed.
The system may also turn on the headlamps when
driving through a parking garage or tunnel.
3-15
ProCarManuals.com

Fog Lamps
If your vehicle has this feature, use the fog lamps for
better visibility in foggy or misty conditions.
Push the button with this
symbol to turn the fog
lamps on or off.
The fog lamp button is located on the instrument panel
next to the exterior lamps switch.
The fog lamp indicator in the instrument panel comes
on when the fog lamps are in use.
The parking lamps or low-beam headlamps must be on,
before the fog lamps can be turned on.
If the exterior lamp control is set to AUTO mode, the
parking lamps and low-beam headlamps come on
simultaneously when the fog lamps are turned on.When the high-beam headlamps are turned on, the fog
lamps turn off automatically. When the high-beam
headlamps are turned off, the fog lamps come on again.
Some localities have laws that require the headlamps
to be on along with the fog lamps.
Instrument Panel Brightness
This feature controls the brightness of the instrument
panel lights.
The thumbwheel for this
feature is located on the
left side of the steering
wheel next to the exterior
lamps control.
Turn the thumbwheel to the right to brighten the lights
or to the left to dim them.
3-16
ProCarManuals.com