2008 RENAULT SCENIC sensor

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-57
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-57V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
5/ TYRE PRESSURE MONITORING SYSTEM FUNCTION
5.1 PROGRAMMING PROCEDURE FOR THE 4 VALVE CODES (SC002)
SC002:
Programming the four valve codes
IMPORTANT:
Any operation involving the replacement of a wheel sensor, requires perfect knowledge of the
recommendations defined in Repair Manual 364 (for Mégane II) or 370 (for Scénic II), section 35.
●Inflate the four tyres to 3.8 bar.
●Establish communication with the UCH using the diagnostic tool.
●Select the Repair mode menu.
●Select the Programming menu.
●Select line SC002 in the Tyre function.
●The stored codes and valve sets detected are displayed.
●Select the Valve set selection menu, then Summer or Winter.
●Confirm to display the Valve programming conditions table.
●Confirm by selecting next to obtain the Find valve codes menu.
●Excite each valve by holding the valve exciter against the tyre just below the valve in question.
●Start with the front left-hand wheel.
●Wait for the new code to appear on the screen before moving on to the next valve.
●The order for programming the codes is as follows:
Front left-hand Front right-hand Rear right-hand Rear left-hand
●Click on the "Confirm" button to transmit the codes to the UCH.
●Inflate the tyres to the recommended pressures.
●Carry out a road test: speed > 12 mph (20 km/h) for 10 minutes.
●Check that no message appears on the instrument panel.
IMPORTANT:
When swapping wheels over, reprogram the UCH with the new valve positions using the diagnostic tool and
program the valve codes.
The coloured rings will then have to be placed back in the location marked on the label on the driver's door.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-62
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-62V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8/ UCH TYPE CONFIGURATION PROCEDURE (SC008)
8.1 Vdiag 44, 48
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
–CF097 Vehicle type (3-door/4-door/5-door/cabriolet/extended MPV/MPV/Estate),
–confirm, follow the procedure and enter the following data:
–CF010 Hands-free function (WITH or WITHOUT),
–CF023 Tyre pressure monitoring system function (WITH or WITHOUT),
–CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
–CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
–CF027 Type of windscreen (TINTED, HEAT INSULATING),
–CF035 Rain/light sensor (WITH or WITHOUT),
–CF014 Daytime running lights (WITH or WITHOUT),
–CF022 Factory fitted perimeter protection (WITH or WITHOUT): function only available on vehicles for the
Mexican market,
–CF173 One-touch window(s)/Sunroof (WITH or WITHOUT),
–confirm, follow the procedure and enter the following data:
–CF036 Selective opening of the opening elements (WITH or WITHOUT) Only if CF010 = WITHOUT
–confirm, follow the procedure and enter the following data:
–CF085 Valet card function (WITH or WITHOUT) Function only available in Mexico,
–(This status will only be available if the following conditions are met: CF036 Selective opening of opening
elements = WITH),
–check that the options configured are those desired and finish.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-63
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-63V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8.2 Vdiag 4C and 4D:
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
CF097 Vehicle type (3-door/4-door/5-door/cabriolet/extended MPV/MPV/Estate).
CF011 Gearbox type (BVA or BVM).
CF020 Type of driving style (Right-hand or Left-hand).
CF028 Engine type (F or K)
–confirm, follow the procedure and enter the following data:
CF010 Hands-free function (WITH or WITHOUT),
CF023 Tyre pressure monitoring system (WITH or WITHOUT),
CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
CF027 Type of windscreen (TINTED, HEAT INSULATING),
CF087 Front fog light (WITH or WITHOUT),
CF014 Daytime running lights (WITH or WITHOUT),
CF012 Rain sensor (WITH or WITHOUT),
CF029 External temperature sensor (WITH or WITHOUT).
–confirm, follow the procedure and enter the following data:
CF036 Selective opening of opening elements (WITH or WITHOUT): Only if CF010 = WITHOUT.
CF016 PAX system type tyre (WITH or WITHOUT): Only if CF097 = MPV or extended MPV or cabriolet and if
CF023 = WITH.
CF100 Deadlocking (WITH or WITHOUT).
CF013 Light sensor (WITH or WITHOUT): Only if CF014 = WITHOUT.
CF022 Factory fitted
perimeter protection (WITH or WITHOUT). Function only available on vehicles sold in
Mexico. CF083 One touch window(s) (WITH or WITHOUT): Absent if CF097 = Cabriolet.
–confirm, follow the procedure and enter the following data:
CF085 Valet card function (WITH or WITHOUT) Function only available in Mexico. Only if CF036 = WITH and
CF023 = WITHOUT.
–check that the options configured are those desired and finish.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-64
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-64V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8.3 Vdiag 4F and 50:
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
–CF097 Vehicle type (3-door/4-door/5-door/cabriolet/Estate) except for Scénic (extended MPV/MPV).
–confirm, follow the procedure and enter the following data:
CF010 Hands-free function (WITH or WITHOUT),
CF023 Tyre pressure monitoring system (WITH or WITHOUT),
CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
CF027 Type of windscreen (TINTED, HEAT INSULATING),
CF035 Rain/light sensor (WITH or WITHOUT),
CF014 Daytime running lights (WITH or WITHOUT),
CF189 Protection type (TYPE 1, TYPE 2 or WITHOUT): TYPE 1 = with factory
fitted perimeter protection, TYPE
2 = with Cobra type alarm and WITHOUT = without factory fitted perimeter protection and without Cobra alarm.
–confirm, follow the procedure and enter the following data:
CF173 One-touch window(s)/sunroof (1 OTW* phase 1/1 OTW* phase 2/2 or 4 OTW*/WITHOUT): Absent if
CF097 = Cabriolet.
1 OTW* phase 1 = 1 driver side one touch window with a phase 1 bodywork vehicle.
1 OTW* phase 2 = 1 driver side one touch window with a phase 2 bodywork vehicle.
2 or 4 OTW = 2 or 4 one touch windows.
WITHOUT = no one touch windows on the vehicle.
–confirm, follow the procedure and enter the following data:
CF188 Production number type (Jxxxxxx or OTHER): only if CF097 = 4-doors and CF173 = 1 OTW* Phase 1.
The production number is located on the oval plate on the vehicle's right-hand side B-pillar. The production number
consists of 7 characters: 1 letter indicating the production plant followed by 6 figures.
–If the production number starts with the letter J, select Jxxxxxx.
–If the production number does not start with the letter J, select Other.
–Confirm, follow the procedure and enter the following data:
CF036 Selective opening of opening elements (WITH or WITHOUT): Only if CF010 = WITHOUT CF016 PAX
System type tyre (WITH or WITHOUT): Only if CF097 = MPV or Extended MPV and if CF023 = WITH.
–confirm, follow the procedure and enter the following data:
CF085 Valet card function (WITH or WITHOUT): Only if CF036 = WITH and CF023 = WITHOUT.
–check that the options configured are those desired and finish.
OTW*: One-touch window(s)IMPORTANT
Only configure WITH valet card function when the vehicle is electrically pre-equipped with the valet option.
Incorrect configuration may cause certain pieces of equipment to malfunction.
Note:
After having finished the UCH configuration, run command AC037 "TRANSMITTING AERIALS FAULT FINDING"
and check that there are no faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-65
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-65V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
9) CONFIGURATION PROCEDURE FOR THE TYRE PRESSURE MONITOR FUNCTION (CF023)
10) INSTRUMENT PANEL CONFIGURATION PROCEDURE (CF145)CF023:
TYRE PRESSURE MONITOR FUNCTION
(in programming command SC008 "UCH type")
WRITING THE CONFIGURATION WITH
OR WITHOUT TYRE PRESSURE MONITOR:
●Select the Repair mode menu.
●Select the Programming menu.
●Select line SC008 then line CF023, then With or Without.
●Confirm the selection.
●Check that sure the configuration has been properly stored by checking the Read configuration menu at line
LC017 Tyre pressure monitor function.
IMPORTANT:
CONFIGURATION INCONSISTENCY BETWEEN THE INSTRUMENT PANEL AND UCH
1st case–The instrument panel detects that the tyre pressure monitor is programmed in the UCH but
not its proper configuration. The message ELECTRONIC FAULT appears, then the
4 wheels disappear on the instrument panel display, and the Service warning light comes
on.
2nd case–The instrument panel detects that the tyre pressure monitor is programmed in its own
configuration but the UCH fails to respond to any requests from the instrument panel (not
configured in UCH). The message TYRE SENSOR FAULT will appear, the four wheels
will disappear from the instrument panel display and the Service warning light will come
on.
CF145:
TYRE PRESSURE MONITOR
●After the multiplex network test, select Instrument panel.
●Select Repair mode.
●Select Write configuration.
●Select line CF145, then With or Without.
●Confirm the selection.
●Check that the configuration has been properly stored in the Read configuration menu at line LC056 Tyre
pressure monitor.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-66
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-66V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
The UCH configurations performed in accordance with the vehicle's equipment level are configured using
the CLIP tool:
Configuration
readingConfigurationName of
configurationChoice of
configurationVdiag
LC001Hands-free functionSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC002External temperature
sensorCF029WITH/WITHOUT 4C, 4D, 4F and 50
LC003DeadlockingCF009WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC004One-touch window(s)SC008 UCH typeWITH/WITHOUT 4C and 4D
LC005Gearbox typeCF011Manual/
Automatic44, 48, 4C, 4D, 4F
and 50
LC006Rain detectorSC008 UCH typeWITH/WITHOUT 44, 48, 4C, 4D
LC007Light sensorSC008 UCH typeWITH/WITHOUT 44, 48, 4C, 4D
LC008Daytime running lightsCF014WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC009Hazard warning lights
illuminated upon impactAutomatic
configurationWITH/WITHOUT 44, 48, 4C, 4D
LC010Tyre type Run flat tyreSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC011Vehicle typeSC008 UCH typeCabriolet/3-door/
All except E and
C44, 48, 4C, 4D
LC012Automatic relockingCF018WITH/WITHOUT 44, 48, 4C, 4D
LC013Type of air conditioningSC008 UCH typeHeating/
Automatic/
Manual 44, 48, 4C, 4D, 4F
and 50
LC014Type of driving styleCF020LEFT-HAND/
RIGHT-HAND 44, 48, 4C, 4D, 4F
and 50
LC015Front fog lightsCF021WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC016Valet card functionSC008 UCH type WITH/WITHOUT 4C, 4D, 4F and 50

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-67
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-67V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
UCH configurations (continued):
T.O*: Sunroof.Configuration
readingConfigurationName of
configurationChoice of
configurationVdiag
LC017Tyre Pressure Monitor
FunctionSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC018Hazard warning lights
switched on by ABS CF024WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC019Rear screen wiper park
position controlAutomatic
configurationWITH/WITHOUT 44, 48, 4C, 4D
LC020Factory fitted perimeter

protection SC008 UCH typeWITH/WITHOUT 4C, 4D, 4F and 50
LC021Type of windscreen
SC008 UCH typeTINTED/HEAT
INSULATING44, 48, 4C, 4D, 4F
and 50
LC023 Engine type CF028F ENGINE/K
ENGINE/M
ENGINE44, 48, 4C, 4D, 4F
and 50
LC025See-me-home lighting CF032WITH/WITHOUT 44, 48, 4C, 4D
LC029 Selective door opening SC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC030Heating resistor type SC008 UCH typeNONE/1000 W/
1800 W 44, 48, 4C, 4D, 4F
and 50
LC035Child safety lockSC016 Child safety
lockWITH/WITHOUT 4C, 4D, 4F and 50
Automatic
configurationWITH/WITHOUT 44 and 48
LC041New vehicle storage modeVP016 ACTIVE/
INACTIVE 4F and 50
LC044 Rain/light sensor SC008 UCH typeWITH/WITHOUT 4F and 50
LC064 Rear screen wiper CF166 WITH/WITHOUT 4F and 50
LC070One-touch window(s)/
sunroof SC008 UCH typeWITH/WITHOUT 4F and 50
LC122Rear access aerialsCF224WITH/WITHOUT 50

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
87B
87B-69
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
87B
87B-69V9 MR-372-J84-87B000$258.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
Tool fault Diagnostic tool title Vdiag
DF001UCH
44, 48, 4C, 4D, 4F, 50 DF002Steering lock
DF003Clutch switch circuit'
DF004Brake light switch circuit
DF005Card
DF006Front left-hand wheel valve sensor
DF007Front right-hand wheel valve sensor
DF008Rear right-hand wheel valve sensor
DF009Rear left-hand wheel valve sensor
DF010Steering column control unit circuit
DF011Rain/light sensor circuit
DF012Right-hand direction indicator circuit
DF013Left-hand direction indicator circuit
DF014Card reader circuit
DF015Optical sensor circuit
DF016At least 2 identical codes/summer set
DF017At least 2 identical codes/winter set
DF018Programming of 4 codes in summer set not performed
DF019Programming of 4 codes in winter set not performed
DF020Front internal aerial circuit
DF021Rear internal aerial circuit
DF022Centre internal aerial circuit
MR-372-J84-87B000$258.mif