2008 RENAULT SCENIC light

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 17V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF004
PRESENT
OR
STOREDRIGHT-HAND OUTER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking distance
control function is ACTIVE (ready): the parking distance control warning light is not lit,
see the interpretation of status ET003 Parking distance control function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
When dealing with a combination of faults on the sensors:
Check the connection and the status of the intermediate connectors (the sensors up to the computer). Repair if
necessary.
Check for + 12 V, after ignition, between tracks 1 and 3 of all the sensors.
Computer with 1 connector:
Check the insulation, continuity and the absence of interference resistance of the supply for each sensor
(between tracks 1 and 3) and for the computer (between tracks 9 and 10).
Computer with 2 connectors:
Check the insulation, continuity and absence of interference resistance of the supply between tracks 1 and 3
for each sensor and between tracks 8 and 11 of the computer 12-track connector.
In the case where only one sensor is faulty:
Swap the defective sensor with a non-defective sensor.
Check for faults:
If the sensor is no longer faulty, replace the defective sensor.
If the fault is still present, with the ignition off, disconnect the parking distance control computer connector to
check the insulation, continuity and the absence of interference resistance on the following connections:
1 connector:
Parking distance control computer Right-hand outer sensor
Track 9 Track 1
Track 16 Track 2
Track 10 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF004/AAP_V08_DF004

PARKING DISTANCE CONTROL
87F
87F - 19V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF005
PRESENT
OR
STOREDRIGHT-HAND INNER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking distance
control function is ACTIVE (READY): the parking distance control warning light is not
lit, see the interpretation of status ET003 Parking distance control function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
If a combination of faults are present on the sensors:
Check the connection and condition of the intermediate connectors (the sensors up to the computer). Repair if
necessary.
Check for + 12 V, after ignition, between tracks 1 and 3 of all the sensors.
Computer with 1 connector:
Check the insulation, continuity and the absence of interference resistance of the supply for each sensor
(between tracks 1 and 3) and for the computer (between tracks 9 and 10).
Computer with 2 connectors:
Check the insulation, continuity and absence of interference resistance of the supply between tracks 1 and 3
for each sensor and between tracks 8 and 11 of the computer 12-track connector.
In the case where only one sensor is faulty:
Swap the defective sensor with a non-defective sensor.
Check for faults:
If the sensor is no longer faulty, replace the defective sensor.
If the fault is still present, with the ignition off, disconnect the parking distance control computer connector to
check the insulation, continuity and the absence of interference resistance on the following connections:
1 connector:
Parking distance control computer Right-hand inner sensor
Track 9 Track 1
Track 13 Track 2
Track 10 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF005/AAP_V08_DF005

PARKING DISTANCE CONTROL
87F
87F - 21V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF006
PRESENT
OR
STOREDBUZZER
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking distance
control function is ACTIVE (READY): the parking distance control warning light is not
lit, see the interpretation of status ET003 Parking distance control function.
Special notes:
The fault is indicated by the absence of the 1-second beep normally emitted by the
buzzer when reverse gear is selected.
Computer with 1 connector:
Switch off the ignition and disconnect the computer's 16-track connector.
Measure the internal resistance of the computer between tracks 2 and 6.
If the value measured is not 314 ΩΩ Ω Ω
or if there is a short circuit across the specified tracks, contact your Techline.
Computer with 2 connectors:
Switch off the ignition and disconnect the computer's 16-track connector.
Measure the internal resistance of the computer between tracks 2 and 10.
If the value measured is not 314 ΩΩ Ω Ω
or if there is a short circuit across the specified tracks, contact your Techline.
Check the connection and condition of the connector on the buzzer.
Replace the connector if necessary.
Switch off the ignition, and disconnect the parking distance control computer 16-track connector to check the
insulation and continuity and ensure the absence of interference resistance on the following connections:
1 connector:
Parking distance control computer Buzzer
Track 2 Track 2
Track 6 Track 1
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF006/AAP_V08_DF006

PARKING DISTANCE CONTROL
87F
87F - 27V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF012
PRESENT
OR
STOREDPARKING DISTANCE CONTROL SWITCH INDICATOR LIGHT
CC.0 : short circuit to earth or open circuit
CO.1 : open circuit or short circuit to + 12 volts
NOTESConditions for applying the fault finding procedure to stored faults:
A fault is declared present after reverse gear is engaged and the parking distance
control deactivation switch is pressed.
Remove the parking distance control switch and check the connections and condition of its connector.
Repair if necessary.
Check for an earth on track B3 of the parking distance control switch connector.
Repair if necessary.
Switch off the ignition, and disconnect the parking distance control computer 16-track connector to check the
insulation and continuity and the absence of interference resistance on the following connection:
Laguna II ph2, Espace IV ph2, Vel-Satis ph2, Mégane II, Scénic II, Laguna II ph1 (1 connector),
Espace IV ph1 (1 connector), Vel-Satis ph1 (1 connector), Laguna II ph1 (2 connectors),
Vel- Satis ph1 (2 connectors), Clio III, Modus ph2:
Parking distance control switch connector Parking proximity sensor computer connector
Track B2 Track 5
Repair if necessary.
Espace IV ph1 (2 connectors):
Parking distance control switch connector16-track parking distance control computer
connector
Track B2 Track 13
Repair if necessary.
If the fault is still present, replace the parking distance control switch.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF012/AAP_V08_DF012

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 31V4 MR-372-J84-87F000$660_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
1 connector:ET001
REVERSE GEAR ENGAGED
NOTESSpecial note:
Only carry out the checks if the YES and NO statuses are not consistent with the
position of the gear lever.
Check that the reversing lights are working correctly: they should come on when reverse gear is selected and go
out when it is not.
If the reversing lights fail to function as specified:
With the ignition switched off, disconnect the parking distance control computer connector to check the
insulation (against + 12 V), and the continuity and absence of interference resistance on the following
connection:
Laguna II ph1 ph2, Espace IV ph1 ph2, Vel-Satis ph2, Clio III, Modus ph2:
Parking distance control computer connector Rear lights connector
Track 4 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Vel-Satis ph1, Scénic II:
Parking distance control computer connector Rear left hand lights connector
Track 4 Track 2
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ET001/AAP_V08_ET001
MR-372-J84-87F000$660_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 32V4 MR-372-J84-87F000$660_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
ET001
(CONTINUED 1)
Mégane II:
Only for 3 and 5-door hatches:
Parking distance control computer connector
(white)Left-hand rear light connector
Track 4 Track 5
Parking distance control computer connector
(white)Right-hand rear light connector
Track 4 Track 1
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Only for 4-door hatches:
Parking distance control computer connector
(white)Left-hand rear light connector
Track 4 Track 5
Parking distance control computer connector
(white)Right-hand rear light connector
Track 4 Track 2
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Only for cabriolets:
Parking distance control computer connector
(white)Left-hand rear light connector
Track 4 Track 6
Parking distance control computer connector
(white)Right-hand rear light connector
Track 4 Track 1
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 33V4 MR-372-J84-87F000$660_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
2 connectors:ET001
(CONTINUED 2)
Only for estates:
Parking distance control computer connector
(white)Left-hand rear light connector
Track 4 Track 5
Parking distance control computer connector
(white)Right-hand rear light connector
Track 4 Track 5
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Laguna II ph1, Espace IV ph1, Vel-Satis ph2, Clio III:
Parking distance control computer connector Rear light connector
Track 6 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Vel Satis ph1:
Parking distance control computer connector Rear light connector
Track 6 Track 2
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 34V4 MR-372-J84-87F000$660_eng.mif
Vdiag No: 04-08
ET002
BUZZER CONTROL
NOTESThere must be no present or stored faults.
ET002
remains OFF
ET002
ON but buzzer does
not sound
Check that the parking distance control system is switched on using status ET003
"Parking distance control function" (parking distance control switch warning light
goes out). If the status displays “suspended” or “deactivated”, restart the system by
pressing for 1 or 3 seconds, consult the interpretation of status ET003 “Parking
distance control function”.
Check that the parking distance control configuration is correct for the vehicle on
which it is fitted (LC005 Vehicle identification). If necessary, reconfigure the
computer using command CF005 Vehicle identification.
Check, when the vehicle is close to an obstacle (between 20 and 150 cm), that the
distance evaluated corresponds to the distance displayed by the diagnostic tool
(PR001 to PR004).
If the distance reading does not match or the distance parameters stay at 255 cm,
contact your Techline.
Check that the buzzer volume is not at a zero setting LC001 Buzzer volume.
If the configured volume is ZERO or DEACTIVATED, reconfigure the computer using
command CF001 Buzzer volume. Select the volume required by the customer.
Switch off the ignition, and disconnect the parking distance control computer 16-track
connector to check the insulation and continuity and ensure the absence of
interference resistance on the following connections:
Laguna II ph2, Espace IV ph2, Espace IV ph1 (1 connector), Vel-Satis ph2,
Vel-Satis ph1 (1 connector), Laguna II ph1 (1 connector),
Parking distance control computer Buzzer
Track 2 Track 1
Track 6 Track 2
Repair if necessary (refer to vehicle wiring diagrams).
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ET002/AAP_V08_ET002