2008 RENAULT SCENIC CD changer

86A-9
MR-372-J84-86A050$177.mif
V3
86A
RADIO
Fault finding - Role of components
Role of main components
–Display: displays various multimedia system data such as the station selected, time, CD listing and satellite
guidance information.
–Steering column control: allows the various system functions to be used via the steering wheel control.
–Speakers and tweeters: relay the sound from the multimedia system into the vehicle.
–CD changer: enables compact discs to be loaded and music to be relayed to the receiver.
–AM/FM aerial: receives radio signals from various transmitters.
–GPS aerial: receives various data transmitted by satellites.
–Radio/navigation computer: manages the various multimedia system functions according to user requests and
transmits audio data to the vehicle via the speakers.
–Cartographic map DVD: loads maps into the navigation computer.
–AM/FM aerial amplifier: improves the reception of AM/FM signals.
–Multimedia network interface unit: enables information to be exchanged between the "vehicle" and "multimedia"
multiplex networks. This computer is involved in activating the multimedia system.
MR-372-J84-86A050$177.mif
LPN RADIO
Vdiag No: C4

86A-10
MR-372-J84-86A050$236.mif
V3
86A
RADIO
Fault finding - Operating diagram
Layout of the main components of the LPN* Radio system:
*LPN: Low Price NavigationV M multiplex line
diagnostic socketUCH
FEED (Kangoo 2)Electric mirror,
passenger side
(Trafic II ph2)
Other computersMultimedia network
interface unit
Multifunction aerial
(Trafic II ph2)Steering column
control
GPS aerialLPN* radio
navigation
Aerial amplifier
(Espace IV ph2,
Scénic II ph2,
Kangoo 2)Passenger
compartment fuse
box and relay
ABS, ABS/ESP or
wheel speed
computer depending
on equipment levelRadio navigation
display
Microphone
CD changer
(if an option)Speakers
Vehicle multiplex network
Multimedia multiplex network
MR-372-J84-86A050$236.mif
LPN RADIO
Vdiag No: C4

86A-12
MR-372-J84-86A050$354.mif
V3
86A
RADIO
Fault finding - Configurations and programming
SETTINGS
VP001: Write VIN
This command permits manual entry of the vehicle's VIN into the computer. Use this command each time
the computer is replaced. The VIN number is inscribed on the manufacturer's plate.
Procedure for writing the VIN
–Establish dialogue with the navigation computer.
–Select the Repair mode menu.
–Select the Other parameters menu.
–Select line VP001 Write VIN.
–Enter the VIN.
–Exit fault finding mode.
–Switch off the ignition.
–Wait for the end of power latch.
–Reread the VIN in the Identification menu for confirmation (ID014 VIN code).
VP003: "Enter After-Sales operation date"
This command is used to enter the date of the last After-Sales operation on the LPN* radio navigation
system.
VP005: Computer calibration and commissioning
This command is used to configure the LPN* radio navigation computer following its replacement. When
the command is complete, switch off the ignition, wait 2 minutes and switch on the ignition again. Check
that the configuration has registered correctly by re-reading the following configuration readings:
–LC008 "Vehicle configuration",
–LC012 "CD changer",
–LC015 "Vehicle type",
–LC016 "Distance units".
The radio is in factory mode after configuration (FM 87.5 MHz in scrambled mode for 2 minutes).
CONFIGURATIONS
CF013: CD changer
This command is used to indicate whether or not a CD changer is present under the front left-hand seat.
CF018: Distance units
This command is used to change the measurement unit for the distances displayed on the radio navigation
screen.
PROGRAMMING
There is no programming on the navigation system.
Important: After activating the system, the delay before establishing dialogue can last 20 seconds.
*LPN: Low Price NavigationNote:
Use the following commands if the configurations are incorrect after having used VP005 Computer calibration
and commissioning.
MR-372-J84-86A050$354.mif
LPN RADIO
Vdiag No.: C4

86A-14
MR-372-J84-86A050$472.mif
V3
86A
RADIO
Fault finding - Fault summary table
Tool fault Associated DTC Diagnostic tool title
DF001 930DFront right-hand speaker
DF002 930FFront left-hand speaker
DF003 930BRear right-hand speaker
DF004 9311Rear left-hand speaker
DF006 9315FM1 ampli
DF022 9368CD changer
DF027 936AComputer
DF028 936BComputer
DF029 936CComputer
DF030 9341Computer configuration
DF032 9341Computer
DF033 9344Computer
DF034 9345Computer
DF035 9346Computer
DF036 9347Computer
DF037 9349Computer
DF038 934AComputer
DF040 93D4No audio CD changer signals
DF056 9328Microphone
DF057 9358Disc error
DF059 93D3Screen
DF060 93D3No display multiplex signal
DF061 93F0Power supply
DF062 9326Power supply
DF064 9327Activation signal
DF065 9324GPS aerial circuit
DF066 934FComputer
DF067 935AComputer
DF068 935CComputer
DF069 934EComputer
DF071 93CFButton jammed
DF072 9325FM1 ampli
MR-372-J84-86A050$472.mif
LPN RADIO
Vdiag No: C4

86A-20
MR-372-J84-86A050$531.mif
V3
RADIO
Fault finding - Interpretation of faults
LPN RADIO
Vdiag No.: C4
86A
DF022
PRESENT
OR
STOREDCD CHANGER
1.DEF: Disc cannot be read
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button,
–a CD is played in the CD changer.
Special notes:
The CD changer is located under the front left-hand seat and is fitted as an option only
on Scénic II ph2.
The CD changer is only compatible with audio CDs.
Check that the CD is not scratched.
Check that the CD format is compatible with the system.
If the fault is still present, replace the CD changer.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
LPN_VC4_DF022

86A-21
MR-372-J84-86A050$531.mif
V3
RADIO
Fault finding - Interpretation of faults
LPN RADIO
Vdiag No.: C4
86A
DF027
DF028
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
–the + after ignition feed is activated,
–a CD is played in the CD changer.
Special notes:
The CD changer is located under the front left-hand seat and is fitted as an option only
on Scénic II ph2.
The CD changer is only compatible with audio CDs.
Check the condition of the CD and its compatibility with the CD changer.
Replace the CD if not correct.
If the fault is still present, replace the CD changer.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
LPN_VC4_DF027/LPN_VC4_DF028

86A-22
MR-372-J84-86A050$531.mif
V3
RADIO
Fault finding - Interpretation of faults
LPN RADIO
Vdiag No.: C4
86A
DF029
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
–the + after ignition feed is activated,
–a CD is played in the CD changer.
Special notes:
The CD changer is located under the front left-hand seat and is fitted as an option only
on Scénic II ph2.
The CD changer is only compatible with audio CDs.
Check that there are no objects that could obstruct the CD changer's ventilation.
Explain to the customer that the CD changer's capacity has been reached (high temperatures).
If the fault is still present, replace the CD changer.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
LPN_VC4_DF029

86A-32
MR-372-J84-86A050$531.mif
V3
RADIO
Fault finding - Interpretation of faults
LPN RADIO
Vdiag No.: C4
86A
*LPN: Low Price NavigationDF040
PRESENT
OR
STORED
NO AUDIO CD CHANGER SIGNALS
1.DEF: No communication with the CD changer
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button,
–a CD is played in the CD changer.
Special note:
If the vehicle does not have a CD changer, check the configuration of the LPN* radio
navigation computer (see Configuration and programming).
Use the wiring diagrams Technical Note for Scénic II ph2.
Look for any damage to the wiring harness and check the condition and connection of the connectors for
components 261 and 1272.
Manipulate the wiring harness in order to observe a change in the fault status (present → stored).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–connection code 34AZ,
–connection code 34BA,
–connection code 34BL,
–connection code 34BC,
–connection code 34BD,
–connection code 34BG,
–connection code 34BH,
between components 261 and 1272.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
LPN_VC4_DF040