2008 RENAULT SCENIC display

86D-23
MR-372-J84-86D000$560.mif
V2
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding - Conformity check
Multimedia network
interface unit
Vdiag No: 04, 14
86D
SUB-FUNCTION: DISPLAY
*LPN: Low Price Navigation
NOTESOnly check conformity after a full check with the diagnostic tool. The values shown
in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
FunctionParameter, Status checked or
ActionDisplay and notes Fault finding
LightingPR005:Dimmed lightingUse the
backlighting wheel
to vary the
parameter value.
Lights on:
from 0 to 100 %
Lights off: 102 %
If there is a fault, refer to ALP 6 "No
LPN* radionavigation backlighting".
Power supplyET004:+ 12 V side lightsINACTIVE
SIGNAL
OFF
ON
LightingET007:BrightnessDAY: Lights off
NIGHT: Lights on
External
temperaturePR004:External
temperatureUnit: ˚CIn the event of a fault, refer to the
interpretation of parameter PR004
Exterior temperature.

86D-25
MR-372-J84-86D000$672.mif
V2
86D
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding - Interpretation of statuses
ET005
SILENCE MODE
NOTESThere must be no present or stored faults.
Engine stopped, ignition on.
Use the wiring diagrams Technical Note for Scénic II ph2, Espace IV ph2,
Trafic II ph2 or Kangoo 2.
Note:
For vehicles which do not have the "Silence" button on the steering column switch,
pressing the +/- twice displays status ET005.
Check the condition and connection of the connector of component 325 (Scénic II ph2 and Kangoo 2: 1519)
and of the black 24-track connector of component 1714.
If the connectors are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Scénic II ph2 and Kangoo 2:
–connection code 34AT,
–connection code 34AR,
–connection code 34AS,
–connection code 34AQ,
–connection code 34AU,
–connection code 34AP,
between components 1714 and 1519.
Trafic II ph2 and Espace IV ph2:
–connection code 34AT,
–connection code 34AR,
–connection code 34AS,
–connection code 34AQ,
–connection code 34AU,
–connection code 34AP,
between components 1714 and 325.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
BIC_V04_ET005/BIC_V14_ET005
Multimedia network
interface unit
Vdiag No: 04, 14
MR-372-J84-86D000$672.mif

86D-37
MR-372-J84-86D000$896.mif
V2
86D
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding - Customer complaints
*LPN: Low Price NavigationNO DIALOGUE WITH THE MULTIMEDIA NETWORK INTERFACE
COMPUTERALP 1
MULTIMEDIA SYSTEM NOT SWITCHING ON ALP 2
INCORRECT DIRECTION OF VEHICLE TRAVEL ALP 3
STEERING COLUMN SWITCH FAULT ALP 4
EXTERNAL TEMPERATURE DISPLAY FAULT ALP 5
NO LPN* RADIO NAVIGATION BACKLIGHTING ALP 6
Multimedia network
interface unit
Vdiag No: 04, 14
MR-372-J84-86D000$896.mif

86D-45
MR-372-J84-86D000$952.mif
V2
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding - Fault Finding Chart
Multimedia network
interface unit
Vdiag No.: 04, 14
86D
ALP 5 Exterior temperature display fault
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Use the W iring Diagrams Technical Note, Trafic II ph2.
Carry out a fault finding procedure on the computer sending the exterior temperature signal:
–Scénic II ph2, Kangoo 2, see 87B, Passenger compartment connection unit.
–Espace IV ph2, see 83A, Instrument panel.
For Trafic II ph2, check the condition and connection of the connector of component 1714 and the connector of
component 240.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance of the following connections:
–connection code 47C,
–connection code 47D,
between components 1714 and 240.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the temperature measured by the sensor does not correspond to the external temperature, measure the sensor
resistance between connections 47C and 47D.
The resistance should be approximately 3000 Ω ± 300 Ω at 20˚C.
Replace the sensor if it is not correct (see MR 408, TRAFIC, Mechanical, 84A, Control - Signals, Temperature
sensor: Removal - Refitting).
If the fault is still present, contact the techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
BIC_V04_ALP5/BIC_V14_ALP5