2008 RENAULT SCENIC brake

AUTOMATIC TRANSMISSION
Fault finding – Conformity check23A
23A - 73V4 MR-372-J84-23A050$462.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
SUB-FUNCTION: STATIONARY DECLUTCHING (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status checked
or ActionDisplay and Notes Fault finding
4Brake pedal
pressedET142:Brake pedal pressedYES, if the brake pedal
is depressed
NO, if the brake pedal
is not depressedIn the event of a
fault, refer to the
interpretation of this
status.
5Brake pedalET003:Brake light switch
(opening)OPEN, brake pedal
released.
CLOSED, brake pedal
depressedIn the event of a
fault, refer to the
interpretation of this
status.
6Brake pedalET004:Brake light switch
(closure)CLOSED, brake pedal
released.
OPEN, brake pedal
depressed.In the event of a
fault, refer to the
interpretation of this
status.

AUTOMATIC TRANSMISSION
Fault finding – Conformity check23A
23A - 75V4 MR-372-J84-23A050$462.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
SUB-FUNCTION: CREEPING AT IDLE SPEED (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
6Standard pedal
positionPR135:Standard pedal
position% In the event of a
fault, consult the
interpretation of this
parameter.
7Brake pedalET003:Brake light
switch (opening)OPEN, brake pedal
released.
CLOSED, brake pedal
depressed.In the event of a
fault, refer to the
interpretation of this
status.
8Brake pedalET004:Brake light
switch (closure)CLOSED, brake pedal
released.
OPEN, brake pedal
depressed.In the event of a
fault, refer to the
interpretation of this
status.
9Gear engagedET013:Gear engagedR for reverse.
1P for 1
st locked.
2P for 2nd locked.
3P for 3rd locked.
4P for 4th locked.
1G for 1st slipping.
2G for 2nd slipping.
3G for 3rd slipping.
4G for 4th slipping.
1 for 1st unlocked.
2 for 2nd unlocked.
3 for 3rd unlocked.
4 for 4th unlocked.In the event of a
fault, refer to the
interpretation of this
status.

AUTOMATIC TRANSMISSION
Fault finding – Status summary table23A
23A - 76V4 MR-372-J84-23A050$528.mif
SIEMENS TA2000
Vdiag No.: 10-11-15AUTOMATIC TRANSMISSION
Fault finding – Status summary table
*SV: solenoid valveTool status Diagnostic tool title
ET001Solenoid valve supply
ET003Brake light switch (opening)
ET004Brake light switch (closure)
ET010Oil too hot signal
ET012Gear lever position
ET013Gear engaged
ET020Exchanger flow control SV* control
ET021Sequence solenoid 1 control
ET022Sequence solenoid 2 control
ET023Sequence solenoid valve 3 control
ET024Sequence solenoid valve 4 control
ET025Sequence solenoid valve 5 control
ET026Sequence solenoid valve 6 control
ET071Torque converter
ET079Economy mode
ET083Old oil
ET097Manual mode
ET108Torque reduction
ET123Multifunction switch S2
ET124Multifunction switch S3
ET125Multifunction switch S4
ET126Multifunction switch P/N
ET127Lower sequential lever switch
ET128Upper sequential lever switch
ET142Brake pedal pressed
ET155Third gear hold contact
ET157Gear lever unlocking
MR-372-J84-23A050$528.mif

AUTOMATIC TRANSMISSION
Fault finding – Interpretation of statuses23A
23A-78V4 MR-372-J84-23A050$594.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ET003
BRAKE LIGHT SWITCH (OPENING)
NOTESThere must be no present or stored faults.
The status displays OPEN with the pedal released and changes to CLOSED with the brake pedal depressed.
Check the cleanliness and the condition of the brake light switch connections.
Check the positioning, setting and correct operation of the brake light switch (Pay attention to the floor carpet which
can block the switch).
Disconnect the battery.
Disconnect the computer. Check the cleanliness and condition of the connections.
Use the Universal bornier Elé. 1681 to check the insulation, continuity and the absence of interference resistance
on the following connection:
●Connection code 5A, between components 119 and 160.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the correct status is not displayed, replace the switch.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2000_V10_ET003/DP0TA2000_V11_ET003/DP0TA2000_V15_ET003

AUTOMATIC TRANSMISSION
Fault finding – Interpretation of statuses23A
23A-79V4 MR-372-J84-23A050$594.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ET004
STOP LIGHT SWITCH (CLOSURE)
NOTESThere must be no present or stored faults.
The status displays CLOSED with the pedal released and changes to OPEN with the brake pedal depressed.
Check the cleanliness and the condition of the brake light switch connections.
Check the positioning, setting and correct operation of the brake light switch (Pay attention to the floor carpet
which can block the switch).
Disconnect the battery.
Disconnect the computer. Check the cleanliness and condition of the connections.
Use the Universal bornier Elé. 1681 to check the insulation, continuity and the absence of interference
resistance on the following connection:
●Connection code 5A, between components 119 and 160.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Repair if necessary.
If the correct status is not displayed, replace the switch.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2000_V10_ET004/DP0TA2000_V11_ET004/DP0TA2000_V15_ET004

AUTOMATIC TRANSMISSION
Fault finding – Parameter summary table23A
23A - 97V4 MR-372-J84-23A050$660.mif
SIEMENS TA2000
Vdiag No.: 10-11-15AUTOMATIC TRANSMISSION
Fault finding – Parameter summary table
ET142
BRAKE PEDAL DEPRESSED
NOTESThere must be no present or stored faults.
This status indicates the position of the brake pedal
The status is YES when the brake pedal is pressed.
The status is NO when the brake pedal is not pressed.
If the status does not function as specified above, use the interpretation of fault DF119 Brake pedal position.
Disconnect the computer.
Check the cleanliness and condition of the connections.
Check the continuity, insulation and the absence of interference resistance on the following connections:
●Connection code 5A between components 119 and 160.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the brake sensor.
If the fault is still present, contact the Techline.
DP0TA2000_V10_ET142/DP0TA2000_V11_ET142/DP0TA2000_V15_ET142
MR-372-J84-23A050$660.mif

AUTOMATIC TRANSMISSION
Fault finding – Parameter summary table23A
23A - 99V4 MR-372-J84-23A050$660.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ET157
GEAR LEVER UNLOCKING
NOTESThere must be no present or stored faults.
This status indicates whether or not the gear lever is unlocked.
Lever in position P.
The status is YES when the brake pedal is pressed.
The status is NO when the brake pedal is not pressed.
Lever in any position except P.
The status is YES whether or not the brake pedal is pressed.
Check that the instrument panel indicates that the lever is in position P.
Check that, when the brake pedal is pressed, the "Press brake pedal" message disappears from the instrument
panel.
Check the gear lever operation up to the multifunction switch.
Adjust the cable if necessary.
Check that statuses ET154, ET123, ET124 and ET125 Multifunction switch are correct.
If the correct status is not displayed, use the interpretation of fault DF095 Gear lever locking electromagnet
circuit.
If the fault is still present, contact the Techline.
DP0TA2000_V10_ET157/DP0TA2000_V11_ET157/DP0TA2000_V15_ET157

AUTOMATIC TRANSMISSION
Fault finding – Customer complaints23A
23A - 114V4 MR-372-J84-23A050$858.mif
SIEMENS TA2000
Vdiag No.: 10-11-15AUTOMATIC TRANSMISSION
Fault finding – Customer complaints
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
NO DIALOGUE WITH THE COMPUTER ALP1
ENGINE STARTING FAULTSALP2
AUTOMATIC TRANSMISSION OPERATING FAULTS ALP3
AUTOMATIC TRANSMISSION MALFUNCTIONING ON
GEAR CHANGINGALP4
ERRATIC GEAR CHANGESALP5
REVERSING LIGHTS DO NOT WORK ALP6
OIL UNDER THE VEHICLEALP7
NO GEAR LEVER LOCK IN POSITION ALP8
GEAR LEVER JAMMED IN "PARK" POSITION (CANNOT
UNLOCK BY DEPRESSING THE BRAKE PEDAL)ALP9
MR-372-J84-23A050$858.mif