2008 PONTIAC G8 ignition

4. Turn the cap counterclockwise
and pull it straight up.
5. When the engine is hot, the level
should be at the hot MAX level.
When the engine is cold, the
uid level should be between
MIN and MAX on the dipstick.
6. Replace the cap.
Adding Power Steering Fluid
To determine what kind of uid
to use, seeRecommended Fluids
and Lubricants on page 11-12.
Always use the proper uid. Failure
to use the proper uid can cause
leaks and damage hoses and seals.
1. Turn the ignition to LOCK/OFF.
2. Top off with power steering
uid. Do not overll the reservoir.
3. Push the cap straight down
and turn clockwise to tighten.
Windshield Washer Fluid
What to Use
When you need windshield washer
uid, be sure to read the
manufacturer’s instructions before
use. If you will be operating
your vehicle in an area where the
temperature may fall below freezing,
use a uid that has sufficient
protection against freezing.
Adding Washer Fluid
Open the cap with the washer
symbol on it. Add washer uid
until the tank is full. SeeEngine
Compartment Overview on page 9-6
for reservoir location. V8 Engine
9-22 Vehicle Service and Care
2008 - Pontiac G8 Owner Manual

Notice:
When using concentrated
washer uid, follow the
manufacturer’s instructions for
adding water.
Do not mix water with
ready-to-use washer uid.
Water can cause the solution
to freeze and damage your
washer uid tank and other
parts of the washer system.
Also, water does not clean as
well as washer uid.
Fill the washer uid tank only
three-quarters full when it is
very cold. This allows for uid
expansion if freezing occurs,
which could damage the tank if
it is completely full.
Do not use engine coolant
(antifreeze) in your windshield
washer. It can damage the
vehicle’s windshield washer
system and paint.
Windshield Wiper Blade
Replacement
Windshield wiper blades should be
inspected for wear or cracking.
To replace the windshield wiper
blades:
1. Turn the wiper switch to the off
position.
2. Turn the ignition to the
LOCK/OFF position.
3. Raise the wiper arm away from
the windshield.4. Press the two clips at either side
of the wiper blade then tilt the
wiper blade at 90° to the
wiper arm and remove.
5. Replace the wiper blade by
pressing in the clip and turning
the blade toward the arm to reset
the clip with the wiper arm.
6. Lower the wiper arm on to the
windshield.
Vehicle Service and Care 9-23
2008 - Pontiac G8 Owner Manual

Fuses UsageF1 Airbag
F2 Trunk Release
F3 Door Locks
F4 Inadvertent
Power LED
F5 Courtesy/Turn
Signal Lamps/Front
Passenger Turn
Signal
F6 Rear and Side
Passenger Side
Turn Signal
F7 Spare
F8 Driver Side Turn
Signal
F9 Body Control
Module
F10 Stoplamps
F11 Interior Lamps
F12 Discrete Logic
Ignition Sensor/Theft
Deterrent System
F13 Rear Cigarette
Lighter
F14 Auxiliary Power
Instrument Panel Fuse Block - Fuse Puller Shown
9-34 Vehicle Service and Care
2008 - Pontiac G8 Owner Manual

Fuses Usage
F10Driver Side
Low-Beam
Headlamp
F11 Spare
F12Passenger Side
Low-Beam
Headlamp
F13 Spare
F14 Spare
F15 Front Wiper
F16 Spare
F17 Theft Horn
F18 Spare
F19Passenger Side
High-Beam
Headlamp
F20 Spare
F21 Windshield Washer
F22Canister Vent
Solenoid
F23Driver Side
High-Beam
Headlamp
F24 SpareFuses Usage
F25 Reverse Lockout
F26 Spare
F27 Spare
F28Engine Control
Module 1
F29 Even Coils/Injectors
F30 Spare
F31 Spare
F32 Emission 2
F33 Emission 1
F34 Spare
F35 Odd Coils/Injectors
F36 Spare
F37 HVAC Ignition
F38Heated
Seats/OnStar
®
Ignition
F39 Engine Ignition
F40 Airbags
F41 Spare
F42Passenger Side
Park Lamp
Fuses Usage
F43Driver Side
Park Lamp
FUSE
PULLERFuse Puller
Relays Usage
R1 Spare
R2 Comm Enable
R3 Spare
R4 Back-up Lamps
R5 Fog Lamp
R6Low-Beam
Headlamps
R7 Spare
R8 Defogger
R9Windshield
Wiper High
R10Windshield
Wiper Low
R11High-Beam
Headlamps
R12 Crank
R13 Powertrain
R14 Ignition Main
Vehicle Service and Care 9-37
2008 - Pontiac G8 Owner Manual

The TPMS operates on a radio
frequency and complies with
RSS-210 of Industry and Science
Canada. Operation is subject to the
following two conditions:
1. This device may not cause
interference.
2. This device must accept any
interference received, including
interference that may cause
undesired operation of the
device.
Changes or modications to this
system by other than an authorized
service facility could void
authorization to use this equipment.Tire Pressure Monitor
Operation
The Tire Pressure Monitor System
(TPMS) is designed to warn the
driver when a low tire pressure
condition exists. TPMS sensors are
mounted onto each tire and
wheel assembly, excluding the
spare tire and wheel assembly. The
TPMS sensors monitor the air
pressure in the vehicle’s tires and
transmit the tire pressure readings to
a receiver located in the vehicle.
When a low tire pressure condition is
detected, the TPMS turns on the
7
low tire pressure warning light.
At the same time a message to
check the pressure in a specic tire
appears on the Driver Information
Center (DIC) display. The low
tire pressure warning light and the
DIC warning message come on
at each ignition cycle until the tires
are inated to the correct ination
pressure. Using the DIC, tire
pressure levels can be viewed bythe driver. For additional information
and details about the DIC operation
and displays seeDIC Operation
and Displays on page 4-23andDIC
Warnings and Messages on
page 4-27.
The low tire pressure warning light
may come on in cool weather
when the vehicle is rst started, and
then turn off as you start to drive.
This could be an early indicator that
the air pressure in the tire(s) are
getting low and need to be inated
to the proper pressure.
A Tire and Loading Information label
shows the size of the vehicle’s
original equipment tires and
the correct ination pressure for the
vehicle’s tires when they are
cold. SeeLoading the Vehicle on
page 8-28, for an example of
the Tire and Loading Information
label and its location on the vehicle.
Also seeInflation - Tire Pressure
on page 9-46.
Vehicle Service and Care 9-51
2008 - Pontiac G8 Owner Manual

The vehicle’s TPMS system can
warn about a low tire pressure
condition but it does not replace
normal tire maintenance. See
Tire Inspection and Rotation on
page 9-54andTires on page 9-39.
Notice:Using non-approved
tire sealants could damage
the Tire Pressure Monitor System
(TPMS) sensors. TPMS sensor
damage caused by using an
incorrect tire sealant is not
covered by the vehicle warranty.
Always use the GM approved
tire sealant available through your
dealer/retailer.
TPMS Malfunction Light and
Message
The TPMS will not function properly
if one or more of the TPMS
sensors are missing or not
operating.
When the system detects a
malfunction, the
7low tire warning
light ashes for about one minute
and then stays on for the remainderof the ignition cycle. A DIC warning
message also displays. The low tire
warning light and DIC warning
message come on at each ignition
cycle until the problem is corrected.
Some of the conditions that can
cause the malfunction light and DIC
message to come on are:
One of the road tires has been
replaced with the spare tire. The
spare tire does not have a TPMS
sensor. The TPMS malfunction
light and DIC message should go
off once the road tire containing
the TPMS sensor is re-installed.
The TPMS sensor matching
process was started but not
completed or not completed
successfully after installing
replacement tires or rotating the
vehicle’s tires. The DIC message
and TPMS malfunction light
should go off once the TPMS
sensor matching process is
performed successfully.
One or more TPMS sensors are
missing or damaged. The DIC
message and the TPMS
malfunction light should go off
when the TPMS sensors are
installed and the sensor matching
process is performed
successfully. See the dealer/
retailer for service.
Replacement tires or wheels do
not match the vehicle’s original
equipment tires or wheels. Tires
and wheels other than those
recommended for the vehicle
could prevent the TPMS from
functioning properly. SeeBuying
New Tires on page 9-56.
Operating electronic devices or
being near facilities using radio
wave frequencies similar to the
TPMS could cause the TPMS
sensors to malfunction.
9-52 Vehicle Service and Care
2008 - Pontiac G8 Owner Manual

If the TPMS is not functioning it
cannot detect or signal a low
tire condition. See the dealer/retailer
for service if the TPMS malfunction
light and DIC message comes
on and stays on.
TPMS Sensor Matching
Process
Each TPMS sensor has a unique
identication code. Any time one or
more of the TPMS sensors are
replaced or the vehicle’s tires are
rotated, the identication codes
need to be matched to the
new tire/wheel location. The sensors
are matched, to the tire/wheel
locations, in the following order:
driver side front tire, passenger side
front tire, passenger side rear
tire, and driver side rear tire using a
TPMS diagnostic tool. See your
dealer/retailer for service.The TPMS sensors can also be
matched to each tire/wheel position
by increasing or decreasing the
tire’s air pressure. When increasing
the tire’s pressure, do not exceed
the maximum ination pressure
indicated on the tire’s sidewall. To
decrease the tire’s air-pressure
use the pointed end of the valve
cap, a pencil-style air pressure
gage, or a key.
You have two minutes to match
each tire and wheel position.
If it takes longer than two minutes to
match any tire and wheel position,
the matching process stops and you
need to start over.The TPMS matching process is
outlined below:
1. Set the parking brake.
2. Turn the ignition switch to
ON/RUN with the engine off.
3. Press and hold the Remote
Keyless Entry (RKE) transmitter’s
lock and unlock buttons, at the
same time, for about ve seconds
to start the TPMS learn mode.
The horn chirps two times
indicating the TPMS receiver is
ready and in learn mode.
4. Start with the driver side front
tire. The driver side front
indicator lamp also comes on to
indicate that corner’s sensor
is ready to be learned.
5. Remove the valve cap from the
tire’s valve stem. Activate the
TPMS sensor by increasing
or decreasing the tire’s air
pressure for about eight seconds.
The horn chirps one time to
conrm the sensor identication
code has been matched to
the tire/wheel position.
Vehicle Service and Care 9-53
2008 - Pontiac G8 Owner Manual

6. The driver side front indicator
lamp turns off and the
passenger side front indicator
lamp comes on to indicate
that corner’s sensor is ready to
be learned. Proceed to the
passenger side front tire and
repeat the procedure in Step 5.
7. The passenger side front
indicator lamp turns off and the
passenger side rear indicator
lamp comes on to indicate that
corner’s sensor is ready to
be learned. Proceed to the
passenger side rear tire and
repeat the procedure in Step 5.
8. The passenger side rear indicator
lamp turns off and the driver side
rear indicator lamp comes on to
indicate that corner’s sensor is
ready to be learned. Proceed to
the driver side rear tire, and
repeat the procedure in Step 5.9. After the driver side rear TPMS
sensor has been learned the
horn chirps two times. The driver
side rear indicator lamp turns
off and the TPMS sensor
matching process is done. Turn
the ignition switch to LOCK/OFF.
If no tires are learned after
entering the TPMS learn mode,
or if communication with the
receiver stops, or if the time limit
has expired, turn the ignition
switch to LOCK/OFF and
start over beginning with Step 2.
10. Set all four tires to the
recommended air pressure level
as indicated on the Tire and
Loading Information label.
11. Put the valve caps back on the
valve stems.Tire Inspection and
Rotation
We recommend that you
regularly inspect the vehicle’s
tires, including the spare tire, for
signs of wear or damage.
SeeWhen It Is Time for New
Tires on page 9-56for more
information.
Tires should be rotated every
5,000 to 8,000 miles (8 000 to
13 000 km). SeeScheduled
Maintenance on page 11-4.
The purpose of a regular tire
rotation is to achieve a uniform
wear for all tires on the vehicle.
This will ensure that your vehicle
continues to perform most like it
did when the tires were new.
9-54 Vehicle Service and Care
2008 - Pontiac G8 Owner Manual