2008 Peugeot 407 C lock
[x] Cancel search: lockPage 77 of 211
4
70
DOORS
Opening the doors from o u t s i d e
Opening the doors from inside
L o c k i n g / u n l o c k i n g f r o m t h e inside
Press the button.
This allows the doors and the boot to
be locked or unlocked.
To make it easier to open the door, the
window lowers automatically by a few
centimetres.
It rises and adjusts automatically on
closing to guarantee perfect sealing.
Before carrying out any work
which requires disconnection
of the battery, lower the win-
dows to permit opening and
closing of the doors.
In the event of a battery cut-off or if the
automatic lowering fails (window iced
up for example), it is still possible to
open the doors. However, it is impera-
tive that the doors are not slammed
when closed.
The safety auto-reverse is inopera-
tive during the automatic raising of the
windows.
Contact a PEUGEOT dealer as soon
as possible.
When using a high pressure washer
on your vehicle, it is recommended
that the end of the gun is kept at least
50 cm away from the windows and
door seals. If the vehicle has been locked
or deadlocked using the key
or the remote control, the but-
ton is inoperative.
In this case, use the key or the remote
control to unlock.
Unlocking from the doors
You can unlock from the inside by op-
erating a door opening control.
If the "Access to the vehicle" function
is activated via the multifunction dis-
play menu, opening:
- the driver's door, unlocks the door
concerned.
- the passenger door, unlocks the
doors and the boot.
Page 78 of 211
4
71
MANUAL LOCKING (EMERGENCY MODE)
A u t o m a t i c c e n t r a l l o c k i n g o f t h e
doors
The doors and boot can lock automati-
cally while driving (speed above 6 mph
[10 km/h]).
You can activate or deactivate this
function by pressing and holding the
button.
BOOT
To open the boot, press the push but-
ton and raise the tailgate.
Tailgate release
This enables the tailgate to be un-
locked in the event of a central locking
fault.
- Fold back the rear seats to gain access to the lock from inside the
boot,
- Insert a small screwdriver into hole
A of the lock to unlock the tailgate.
Note: driving with the doors
locked may make access to the
passenger compartment by the
e m e r g e n c y s e r v i c e s m o r e d i f fi -
cult in an emergency.
If the permanent locking of the
boot is activated, opening is
only possible by pressing the
remote control button.
Passenger door
To lock, insert the key in the control
located on the edge of the door then
push to the left.
Driver’s door
Insert the key in the lock to lock or un-
lock the door.
Page 79 of 211
4
71
MANUAL LOCKING (EMERGENCY MODE)
A u t o m a t i c c e n t r a l l o c k i n g o f t h e
doors
The doors and boot can lock automati-
cally while driving (speed above 6 mph
[10 km/h]).
You can activate or deactivate this
function by pressing and holding the
button.
BOOT
To open the boot, press the push but-
ton and raise the tailgate.
Tailgate release
This enables the tailgate to be un-
locked in the event of a central locking
fault.
- Fold back the rear seats to gain access to the lock from inside the
boot,
- Insert a small screwdriver into hole
A of the lock to unlock the tailgate.
Note: driving with the doors
locked may make access to the
passenger compartment by the
e m e r g e n c y s e r v i c e s m o r e d i f fi -
cult in an emergency.
If the permanent locking of the
boot is activated, opening is
only possible by pressing the
remote control button.
Passenger door
To lock, insert the key in the control
located on the edge of the door then
push to the left.
Driver’s door
Insert the key in the lock to lock or un-
lock the door.
Page 80 of 211
4
72
SUNROOF
To tilt the roof: press and hold part A
of the switch.
To open the roof in sliding mode: tilt
the sunroof, then press part A of the
s w i t c h b r i e fl y .
To close it in sliding mode: press
part B o f t h e s w i t c h b r i e fl y .
To close it in tilt mode: press and
hold part B of the switch.
S a f e t y a u t o - r e v e r s e
When the sunroof is sliding closed and
meets an obstacle, it stops then par-
tially opens again. Pressing the locking button
on the remote control key for
more than 2 seconds closes
the sunroof in sliding mode.
The sunroof remains tilted.
To close the sunroof completely, press
and hold part B of the switch before
getting out of the vehicle.
Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
Always ensure that the sun-
roof is closed correctly before leaving
the vehicle.
In the event of contact during closing in
tilt mode, you must reverse the move-
ment of the roof. To do this, press the
switch concerned.
When the driver closes the roof in tilt
mode, he must ensure that no one is
preventing correct closing of the roof.
The driver must ensure that the pas-
sengers use the sunroof correctly.
Be aware of children when operating
the roof.
Notes:
In the event of unwanted opening of
the roof on closing (for example, in the
presence of ice), press and hold part
B of the switch, w i t h i n t h e t w o s e c -
onds which follow the triggering of the
safety auto-reverse, until the sunroof
closes completely.
Following reconnection of the bat-
tery or in the event of a malfunction,
press and hold part B of the switch,
the sunroof slides "step by step" until
it closes. Continue to press the switch
for approximately one second after
closing.
T h e s a f e t y a u t o - r e v e r s e f u n c t i o n i s
n o t a c t i v e d u r i n g t h e s e o p e r a t i o n s . S h u t t e r
The sunroof shutter is manual.
To open it, slide it rearwards using the
handle.
To close it, slide it forwards using the
handle.
D o n o t o p e n t h e s u n r o o f i m m e d i -
a t e l y a f t e r a s h o w e r o r i m m e d i a t e l y
a f t e r w a s h i n g t h e c a r .
Page 83 of 211
5
75
The timed duration must also
be set, via the multifunction
display "Personalisation -
C o n fi g u r a t i o n " menu.
A u t o m a t i c s w i t c h i n g o n o f t h e lights
To switch the function on
or off, use the multifunction
display "Personalisation -
C o n fi g u r a t i o n " menu. Activation
Deactivation
When this function is activat-
ed, the indicator light on the
instrument panel comes on.
When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
M a n u a l " f o l l o w - m e - h o m e " l i g h t i n g
If the automatic switching on of the lights
is not activated, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
A u t o m a t i c " f o l l o w - m e - h o m e "
lighting
When you leave your vehicle with
the
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
activated , the side lights and dipped
headlamps remain on for the duration se-
lected when the ignition is switched off.
To activate or deactivate this func-
tion, pass via the multifunction display
" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
menu.
In foggy weather, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi -
cient light. As a consequence,
the lights will not come on au-
tomatically.
This function is active when the vehi-
cle is supplied to the customer.
If the brightness sensor does not
f u n c t i o n c o r r e c t l y , if the system is
activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes on
on the instrument panel.
* According to country.
This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.
The side lights and dipped beam head-
lamps switch on automatically if the light
is poor, or during operation of the wind-
screen wipers. They switch off as soon
as the light becomes bright enough or
the windscreen wipers stop.
Page 84 of 211
5
75
The timed duration must also
be set, via the multifunction
display "Personalisation -
C o n fi g u r a t i o n " menu.
A u t o m a t i c s w i t c h i n g o n o f t h e lights
To switch the function on
or off, use the multifunction
display "Personalisation -
C o n fi g u r a t i o n " menu. Activation
Deactivation
When this function is activat-
ed, the indicator light on the
instrument panel comes on.
When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
M a n u a l " f o l l o w - m e - h o m e " l i g h t i n g
If the automatic switching on of the lights
is not activated, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
A u t o m a t i c " f o l l o w - m e - h o m e "
lighting
When you leave your vehicle with
the
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
activated , the side lights and dipped
headlamps remain on for the duration se-
lected when the ignition is switched off.
To activate or deactivate this func-
tion, pass via the multifunction display
" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
menu.
In foggy weather, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi -
cient light. As a consequence,
the lights will not come on au-
tomatically.
This function is active when the vehi-
cle is supplied to the customer.
If the brightness sensor does not
f u n c t i o n c o r r e c t l y , if the system is
activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes on
on the instrument panel.
* According to country.
This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.
The side lights and dipped beam head-
lamps switch on automatically if the light
is poor, or during operation of the wind-
screen wipers. They switch off as soon
as the light becomes bright enough or
the windscreen wipers stop.
Page 89 of 211
5
79
COURTESY LIGHTS
1 . F r o n t c o u r t e s y l i g h t
2 . Front map reading lights
With the ignition on, operate the relevant switch.
3 . R e a r c o u r t e s y l i g h t
4 . Rear map reading lights
With the ignition on, operate the relevant switch. Deactivation
The courtesy lights can be deactivat-
ed by pressing switch
1 for more than
three seconds. Pressing switch 1 or
3 b r i e fl y s w i t c h e s t h e c o r r e s p o n d i n g
courtesy light on and off.
The map reading lights are not affected
by this and can still be switched on.
Activation
To re-activate the automatic lighting,
press switch 1 again.
S i l l i l l u m i n a t i o n
The sill lighting is at the bottom of each
door trim.
The lights come on automatically
when a door is opened and switch off
automatically when all of the doors are
closed.
Boot light
The boot light is located in the right-
hand boot trim.
It comes on automatically when the
boot is opened and switches off auto-
matically when the boot is closed.
Pressing switch 1 or 3 switches on the
corresponding courtesy light for ten
minutes.
The front and rear courtesy lights come
on automatically when the ignition key
is removed, on unlocking the vehicle
or on opening one of the doors.
They gradually go off after the ignition
has been switched on or the vehicle
is locked.
Page 94 of 211
7
84
ELECTRONIC STABILITY PROGRAMME (ESP)
The electronic stability programme
(ESP) incorporates the following sys-
tems:
- the anti-lock braking system (ABS) and the braking system (EBFD),
- the emergency braking assistance system,
- the traction control (ASR),
- the dynamic stability control (DSC).
Traction control (ASR)
The ASR system optimises traction in
order to avoid wheel slip by acting on
the brakes of the driving wheels and
on the engine. It also improves the
directional stability of the vehicle on
acceleration.
Dynamic stability control
(DSC)
If there is a difference between the
path followed by the vehicle and that
required by the driver, the DSC moni-
tors each wheel and automatically acts
on the brake of one or more wheels
and on the engine to return the vehicle
to the required path, within the limits of
the laws of physics.
Operating modes
Definitions
Emergency braking assistance
system
In an emergency, this system enables
you to reach the optimum braking
pressure more quickly and therefore
reduce the stopping distance.
It is triggered in relation to the speed
at which the brake pedal is pressed.
This is felt by a reduction in the resis-
tance of the pedal and an increase in
the effectiveness of the braking. When this warning light
comes on, accompanied by
a buzzer and a message, it
indicates that there is a mal-
function of the ABS, which
can cause a loss of control of the ve-
hicle when braking.
When this warning light
comes on, connected to
the STOP and ABS warn-
ing lights, accompanied by
a buzzer and a message, it
indicates that there is a malfunction of
the electronic brake force distribution,
which can cause a loss of control of
the vehicle when braking.
Stop immediately.
In both cases, consult a PEUGEOT
dealer.
Anti-lock braking
system (ABS) and braking
system (EBFD)
This system improves the stability and
manoeuvrability of your vehicle when
braking and offers improved control,
in particular on poor or slippery road
surfaces.
The ABS prevents wheel lock in the
event of emergency braking.
The braking system provides integral
management of the braking pressure
wheel by wheel. Anti-lock braking system (ABS)
and braking system (EBFD)