2008 Peugeot 407 C display
[x] Cancel search: displayPage 22 of 211
1
25
T y r e u n d e r - i n fl a t i o n
detection system warning
light
This indicates the absence or
malfunction of one or more
tyre pressure sensors or a system fault.
Consult a PEUGEOT dealer.
Electronic engine
immobiliser warning light
This indicates an electronic
engine immobiliser system
malfunction.
Consult a PEUGEOT dealer. Front brake pads wear
warning light
This indicates that the brake
pads are worn.
For your safety, have them replaced
by a PEUGEOT dealer.
Fuel tank cap warning light
(according to version)
With the engine running, this
indicates that the fuel tank
cap is incorrectly secured or
absent.
It comes on in orange if the vehicle
speed is below 6 mph (10 km/h) and
in red if the vehicle speed is above 6
mph (10 km/h).
Door/boot open warning
light
With the engine running, this
indicates that an access has
not been closed correctly.
An illustration on the multifunction
d i s p l a y i d e n t i fi e s t h e a c c e s s ( e s ) c o n -
cerned.
It comes on in orange if the vehicle
speed is below 6 mph (10 km/h) and
in red if the vehicle speed is above 6
mph (10 km/h). Air bags warning light
This indicates an air bag
fault.
Consult a PEUGEOT dealer.
Automatic headlamp
beam adjustment system
warning light
This indicates that the auto-
matic headlamp height ad-
juster is faulty.
Consult a PEUGEOT dealer.
Punctured tyre warning
light
This indicates that one or
more punctured tyres have
been detected.
A message on the multifunction display
i d e n t i fi e s t h e w h e e l ( s ) c o n c e r n e d .
It is linked with the STOP warning
light.
Stop immediately.
Change the damaged wheel and have
it repaired by a PEUGEOT dealer.
Engine oil pressure
warning light
This indicates that the engine
oil pressure is too low.
It is linked with the STOP warning
light.
Stop immediately if it comes on while
the engine is running.
If there is a lack of oil in the lubrication
circuit, top up the level and contact a
PEUGEOT dealer as soon as possible.
Page 23 of 211
1
26
Electronically controlled
suspension indicator
lights
This comes on when the
SPORT function is activated.
Automatic switching on of
the lights indicator light
This comes on when the
AUTO function is activated.
Automatic switching on
of the lights deactivation
indicator light
This comes on when the AUTO
function is deactivated.
Automatic wipers indicator
light
This comes on when the
AUTO function is activated.
Automatic wipers
deactivation indicator light
This comes on when the AUTO
function is deactivated.
Service warning light
This is displayed to indicate
an engine management sys-
tem fault.
Contact a PEUGEOT dealer as soon
as possible.
Electronically controlled
suspension fault warning
light
This indicates an electroni-
cally controlled suspension
malfunction.
Select automatic operation and con-
tact a PEUGEOT dealer as soon as
possible.
Obstacle proximity
detection system warning
light
In forward and/or reverse
gear, this indicates an obsta-
cle proximity detection system fault.
Consult a PEUGEOT dealer. This comes on when the
SPORT function is deacti-
vated.
P a r t i c l e e m i s s i o n fi l t e r
saturation warning light
(Diesel engine)
With the engine running, this
indicates that the particle
e m i s s i o n fi l t e r i s s t a r t i n g t o b e c o m e
saturated (exceptionally prolonged ur-
ban driving type conditions: low speed,
l o n g t r a f fi c j a m s . . . ) o r a l o w d i e s e l a d -
ditive reservoir level.
I n o r d e r t o r e g e n e r a t e t h e fi l t e r , y o u a r e
advised to drive, as soon as possible
w h e n t h e t r a f fi c c o n d i t i o n s p e r m i t , a t a
speed of 40 mph (60 km/h) or above
f o r a t l e a s t fi v e m i n u t e s ( u n t i l t h e w a r n -
ing light is switched off).
If the warning light remains on, contact
a PEUGEOT dealer.
Following prolonged use of the vehi-
cle at very low speeds or at idle, you
may, exceptionally, notice an emission
of water vapour at the exhaust during
acceleration. This does not affect the
performance of the vehicle or the en-
vironment. W a t e r i n d i e s e l fi l t e r
warning light
This indicates the presence
o f w a t e r i n t h e d i e s e l fi l t e r .
There is a risk of damage to
the injection system.
Contact a PEUGEOT dealer as soon
as possible.
Page 24 of 211
1
27
Coolant temperature indicator
When the needle is in zone A , the
temperature is correct.
When the needle is in zone B , the
temperature is too high.
If the coolant temperature
warning light comes on
(linked with the STOP warn-
ing light), stop immediately.
Wait for the engine to cool
down before topping up the level, if
necessary.
As the cooling circuit is pres-
surised, in order to prevent
any risk of scalding, unscrew
the cap by two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level with
coolant, if necessary.
Consult a PEUGEOT dealer.
This indicates an automatic
gearbox programme fault.
Automatic gearbox lever position indicator lights
Automatic gearbox fault
warning light
This indicates an automatic
gearbox fault.
The gearbox will operate in down-
grade mode, locked in 3rd gear.
Never force the selector lever.
Consult a PEUGEOT dealer.
6 speed automatic gearbox
"Park" indicator
lights
"Reverse" indicator
lights
"Neutral" indicator
lights
"Drive" indicator
lights
The letter S or the symbol
, associat-
ed with the gate lever position indicator
lights, corresponds to the Sport or Snow
programme selected intentionally. "Manual" indicator lights
These correspond to the manual con-
trol of the gearbox.
When the engine speed is too low
or too high in relation to the gear en-
g a g e d , t h e g e a r s e l e c t e d fl a s h e s f o r
a few seconds, then the actual gear
is displayed, the auto-adaptive pro-
gramme having taken control tempo-
rarily.
Page 25 of 211
1
28
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer’s servicing schedule.
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
n e r fl a s h .
Example: when the ignition is switched
on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user’s driving habits.
Engine oil temperature indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is lit.
The trip recorder display shows the
d i s t a n c e r e m a i n i n g ( i n r o u n d fi g u r e s )
before the next service.
Example: when switching on the ig-
nition and for 5 seconds, the display
shows that 900 miles/km remain be-
fore the next service is due.
Page 26 of 211
1
28
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer’s servicing schedule.
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
n e r fl a s h .
Example: when the ignition is switched
on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user’s driving habits.
Engine oil temperature indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is lit.
The trip recorder display shows the
d i s t a n c e r e m a i n i n g ( i n r o u n d fi g u r e s )
before the next service.
Example: when switching on the ig-
nition and for 5 seconds, the display
shows that 900 miles/km remain be-
fore the next service is due.
Page 27 of 211
1
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service your-
self, the re-set procedure is as follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information.
Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil reservoir
cap, using the type of oil
suited to your engine.
A = max.
B = min.
Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y c h e c k -
ing using the dipstick, it is imperative
that the level is topped up. Oil level gauge fault
( fl a s h i n g s e g m e n t s )
Check the oil level using the dipstick.
I f t h e l e v e l i s c o r r e c t , t h e fl a s h i n g i n d i -
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes.
After this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
fi v e m i n u t e s , o t h e r w i s e t h e
zero re-set will not be registered.
Page 28 of 211
1
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service your-
self, the re-set procedure is as follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information.
Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil reservoir
cap, using the type of oil
suited to your engine.
A = max.
B = min.
Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y c h e c k -
ing using the dipstick, it is imperative
that the level is topped up. Oil level gauge fault
( fl a s h i n g s e g m e n t s )
Check the oil level using the dipstick.
I f t h e l e v e l i s c o r r e c t , t h e fl a s h i n g i n d i -
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes.
After this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
fi v e m i n u t e s , o t h e r w i s e t h e
zero re-set will not be registered.
Page 29 of 211
1
30
Trip recorder zero reset
With the trip distance displayed, press
the button for a few seconds.
Distance recorder
The total distance is displayed in zone
A of the display and the trip distance
in zone B .
LIGHTING RHEOSTAT
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the minimum (or max-
imum) setting, release the button then
press it again to increase (or reduce)
the brightness.
As soon as the lighting is of the
required brightness, release the button.