Page 131 of 211
1010
118
CHANGING A WINDSCREEN WIPER BLADE
ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
LOAD REDUCTION FUNCTION
When driving, certain functions (air
conditioning, heated rear screen,
heating system for passenger com-
partment of diesel vehicles, etc.) may
be switched off temporarily, depending
on the level of battery charge.
Reactivation of these functions is au-
tomatic, once the battery charge is
s u f fi c i e n t .
Note: at the risk of discharg-
ing the battery, the functions
that have been switched off
may be reactivated manually.
Note: if the telephone is being
used when economy mode
starts, it will still be possible to
fi n i s h t h e c a l l .
A fl a t b a t t e r y p r e v e n t s t h e e n -
gine from starting.
Replacing a blade
Lift the arm, then unclip the blade
and remove it.
Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. Once the hour is over, a switching to
economy mode message appears on
the multi-function display and the ac-
tive functions are put on standby.
These functions are reactivated au-
tomatically next time the vehicle is
driven.
In order to resume the use of these
functions immediately, the engine
must be started and left to run for a
few minutes.
The time available to you will then be
approximately double the duration
for which the engine is left running.
However, this period will always be
b e t w e e n fi v e a n d t h i r t y m i n u t e s .
T h i s t i m e m a y b e s i g n i fi c a n t l y
reduced if the battery charge
is low.
Placing the wiper blades in the
maintenance position
Less than one minute after switching
off the ignition, press the windscreen
wiper stalk down once to position the
blades at the top of the windscreen
(maintenance position).
Page 133 of 211
1010
120
Before disconnecting the bat-
tery, you must wait for 2 minu-
tes after switching off the
ignition.
Never disconnect a terminal when the
engine is running.
N e v e r c h a r g e a b a t t e r y w i t h o u t fi r s t
disconnecting the terminals.
Open the windows and close the sun-
roof before disconnecting the battery.
If they do not operate normally follow-
ing reconnection of the battery, they
must be reinitialised (see paragraphs
"Reinitialisation of the electric win-
dows" and "Sunroof").
After every reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to allow the
electronic systems to be initialised.
H o w e v e r , i f s l i g h t d i f fi c u l t i e s a r e e x -
perienced after this, please contact a
PEUGEOT dealer.
On the 2.7 litre 24V HDI engine, if
there is no battery in the boot, do
not connect a slave battery to the
positive (+) and negative (-) termi-
nals under the bonnet as a short
circuit may occur.
The batteries contain harmful
substances such as sulphuric
acid and lead. They must be
disposed of in accordance
with regulations and must never be
discarded with household waste.
Take used batteries to an approved
collection point.
open the bonnet,
use the two additional positive (+)
and negative (-) terminals located
under the bonnet,
open the red cover of the positive
(+) terminal,
connect the red cable between the
positive (+) terminal and the positive
(+) terminal of the slave battery,
connect the green or black cable
between the negative (-) terminal
and the negative (-) terminal of the
slave battery,
operate the starter, let the engine
run,
wait for the engine to return to idle,
then disconnect the cables,
close the red cover of the positive
(+) terminal,
r e fi t t h e l e f t s i d e c o v e r ,
close the bonnet. BOOT) *
* V e h i c l e s fi t t e d w i t h t h e 2 . 7 l i t r e H D I
24 V engine.
The battery is in the left boot trim.
To charge the battery using a battery
charger (boot open):
fold down the panel to gain access
to the battery,
disconnect the battery,
follow the instructions for use given
by the battery charger manufacturer,
reconnect starting with the nega-
tive (-) terminal,
raise the panel and close it. To start the vehicle from another
battery:
Page 180 of 211
11
2 2
3 3
11
2 2
5 511
0 4
165
H A N D S - F R E E K I T
D I S P L A Y C
For safety reasons and because they require prolonged attention on the part of the driver, the operations for matching of the Bluetooth mobile telephone with the WIP Sound hands-free kit must be carried out with the vehicle stationary and the ignition on.
E n t e r t h e v e h i c l e ' s a u t h e n t i c a t i o n c o d e ( = 1 2 3 4 ) . Depending on the telephone, you may be asked to enter this code before the superimposed c o n fi g u r a t i o n d i s p l a y a p p e a r s .
Activate the telephone's Bluetooth function and carry out a search of the Bluetooth accessories present for the telephone.
Select the accessory which corresponds to the n a m e o f t h e v e h i c l e , a s u p e r i m p o s e d c o n fi g u r a t i o n display appears on the multifunction display.
The services offered by the hands-free kit depend on the telephone network, the SIM card and the compatibility of the Bluetooth equipment used. Consult your telephone's manual and your operator to check which services are available to you. A list of mobile telephones which offer the best range of services is available from the network. Consult a PEUGEOT dealer.
R E C E I V I N G A C A L L
Select the YES tab on the display using t h e b u t t o n s t h e n c o n fi r m b y p r e s s i n g O K .
An incoming call is announced by a ring and a supe rimposed display on the multifunction display.
Y E S
Y E S
Select the YES tab on the display u s i n g t h e b u t t o n s a n d c o n fi r m b y pressing OK.
Press the end of the steering wheel stalk to accept the call.
Press the end of the steering wheel stalk for more than two seconds to access your directory.
If you wish to dial a number, use the keypad on yo ur telephone.
M A K I N G A C A L L
M A T C H I N G A T E L E P H O N E